Bedienungsanleitung Elica Cube (Seite 9 von 12) (Englisch)

471136

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Consult the designs in the front pages referenced in the text

by alphabet letters. Closely follow the instructions set

out in this manual. All responsibility, for any eventual

inconveniences, damages or fires caused by not complying

with the instructions in this manual, is declined.

The cooker hood must be placed at a minimum distance of

50 cm from the cooking plane for electric cookers and 75cm

for gas or mixed cookers.The hood can be installed above

these heights but for optimum performance it should be

installed at the distance quoted for the appropriate heat

source.

The hood is equipped with a top air outlet B for discharge

of fumes to the outside (Ducting version  exhaust pipe

and pipe fixing clamps not provided).

Should it not be possible to discharge cooking fumes and

vapour to the outside, the hood can be used in the filter

version, fitting an activated carbon filter and the deflector F

on the support (bracket) G, fumes and vapours are

recycled through the top grille H by means of an exhaust

pipe connected to the top air outlet B and the connection

ring mounted on the deflector F (exhaust pipe and pipe

fixing clamps not provided).

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

(not supplied).

Expansion wall plugs are provided to secure the hood to

most types of walls/ceilings. However, a qualified technician

must verify suitability of the materials in accordance with the

type of wall/ceiling. The wall/ceiling must be strong enough

to take the weight of the hood.

Installation

Preliminary information for installation of the hood:

Disconnect the hood during electrical connection, by turning

the home mains switch off.

Remove the fat/s filter/s and the carbon filter frame.

Do not tile, grout or silicone this appliance to the wall. Surface

mounting only. Do not fix chimney flue to furniture or fly over

shelves unless the chimney flue can be easily removed,

in case maintenance is ever required.

Assembling the chimney flue support/bracket (3

parts):

The three parts should be fixed with 4 screws, the support

extension is adjustable and should correspond to the internal

width of the telescopic chimney flue.

Assembling the deflector (only when a deflector

composed of 3 parts is supplied  the deflector should

be only for the filter version):

The three parts should be fixed with 2 screws, the deflector

extension is adjustable and should correspond to the width

of the chimney flue support, to which it is then fixed.

Remove AND CONSERVE the screws that temporarily

fix the flue units (for reasons of transport), the hood

or the flue unit (on the basis of the model possessed)

with the suction unit. The two parts should be

disassembled to facilitate installation. Check how the parts

are fixed together to repeat assemblage at the opportune

moment.

Attention!

The chimney is predisposed for installation of the filter

Version.

In certain models where it is required to use the cooker hood

in the suction version then it is possible to overturn the upper

section of the chimney

and insert it inside the lower section of the chimney so that

the air-exit perforations are not visible. The chimneys in

which this operation is possible are recognizable by their

bracket fixing points G which are repeated also in the lower

side of the upper section of the chimney (see installation

sequence 20a-20b).

Attention! for all pre-assembled models:

the mounting operations 1, 2, 3 should not be taken into

consideration, for installation begin at operation 4.

1. Rest the suction unit on a flat surface and thread the lower

part of the hood onto it (Fig. 1C/8C - 1D/8D - 1I/8I - 1E/

8E - 1F/8F - 1G/8G - 1H-8H).

2. Make all the electrical connections between the two parts

(Fig. 9).

3. Permanently fix the cooker hood to the suction group with

the screws (consult the figure corresponding to the model

in possession)(Fig. 1C/8C - 1D/8D - 1I/8I - 1E/8E - 1F/

8F - 1G/8G - 1H-8H).

4. Using a pencil, draw a line on the wall, extending up to

the ceiling, to mark the centre. This will facilitate

installation (Fig. 10).

5. Rest the drilling template against the wall: the vertical

centre line printed on the drilling template must correspond

to the centre line drawn on the wall, and the bottom edge

of the drilling template must correspond to the bottom

edge of the hood: bear in mind that, when installation is

complete, the underside of the hood must be at least 50

cm above the cooker top in the case of electric cookers,

and at least 75 cm above the cooker top in the case of

gas or mixed cookers.

6. Place the lower support bracket on the perforation

diagram making it coincide with the traced triangle, mark

the two external holes and perforate. Remove the

perforation diagram, insert two wall-dowels and fix the

support bracket of the hood with two 5x45 mm screws

(Fig. 10).

Attention: only the models illustrated in Fig. 1Q/

10Q:

Fix the central bracket with two screws and wall-dowels

above the lower bracket (see perforation diagram for

positioning the holes).

7. Hang the hood onto the lower bracket.

8. Adjust the distance of the hood from the wall.

9. Adjust the horizontal position of the hood.

10.Using a pencil mark the cooker hood permanent drill hole

inside the suction group (1 or 2 fixing points are

necessary for permanent mounting) (Fig. 11).

Elica Cube Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info