Bedienungsanleitung Elica ELISLIM (Seite 4 von 5) (Englisch)

471238

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Introduction to the Hood - Fig. 1

1. Light Switch

2. Motor Speed Switch

3. Light Covers - illumination of the Cooking

Surface

4. Grease Filters

5. Grease Filter Support Grate (the grease

filters are located within).

6. Light Cover Supports

7. Pull-Out Drawer

Model with Self-supporting Metal

Filters

Removing the Grease Filters - Fig. 2

a. Remove the pull-out drawer completely.

b. Press the side handles (A) towards the

opposite side and remove the filters.

Putting the Filters Back in Place

a. Remove the pull-out drawer completely

and mount the grease filter so that it

covers the drawer.

b. Close the drawer and install the remaining

grease filter.

Opening the Light Cover Support

a. Remove the pull-out drawer completely.

b. Push the B knobs inwards toward each

other (in the “Open” direction as indicated

on the plastic knob itself).

Model with Grease Filter Support

Grate

Opening the Grease Filter Support Grates

- Fig. 3

a. Remove the pull-out drawer completely.

b. Push the B knobs inwards toward each

other (in the “Open” direction as indicated

on the plastic knob itself).

c. To remove the grates completely, use

the N spring fasteners, which act as pins

to hold the grate in place (Fig. 4).

Systems Available

Two systems are available:

Venting Outdoors

The air is vented outdoors through a duct

which must be connected to the exhaust

opening (C - Fig. 5) by means of the flange

(D). The diameter of the exhaust duct must

be exactly the same as that of the flange.

Air Recirculation

— The air is cleaned by means of charcoal

filters (one or two depending on the

model) and then circulated back into the

room.

— The use of a charcoal filter is necessary

when the hood cannot vented outdoors

either because ducting is not available or

cannot be installed.

— The filtered air is returned from atop the

cabinet through a duct that passes

through the cabinet itself.The diameter

of the duct must be the same as that of

flange D (Fig. 5).

The installion (or removal) steps are identical

for hoods with either 1 or 2 motors:

a. Request a charcoal filter from the retailer,

specifying the model and type of hood (1

filter for a hood with one motor and 2

filters for a hood with 2 motors).

Caution! Some charcoal filters come

covered with a plastic film to protect their

filtering properties. If this is the case, remove

the film before installing the filter.

b. Remove the pull-out drawer completely.

c. Remove the grease filters or the grates.

d. Open the light cover support.

e. Install the charcoal filter so that it covers

the plastic grate which protects the

ventilation fan (Fig. 6).

f. Turn the center handle in the clockwise

direction until it locks in place.

g. Remount the grease filters and the grates.

Installation

When installed, the distance between the

hood and burners must be not less than 65

cm for electric burners or 70 cm for gas or

mixed-fuel burners.

Do not tile, grout or silicone this appliance

to the wall. Surface mounting only.

Do not fix chimney flue to furniture or fly over

shelves unless the chimney flue can be

easily removed, in case maintenance is

ever required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica ELISLIM Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info