Bedienungsanleitung Elica Glide (Seite 6 von 8) (Englisch)

471151

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Consult the designs in the front pages referenced in the text by

alphabet letters. Closely follow the instructions set out in

this manual. All responsibility, for any eventual inconveniences,

damages or fires caused by not complying with the instructions

in this manual, is declined.

Description of the hood - Fig. 1

1 Control panel

2 Grease filter

3 Grease filter release handle

4 Halogen lamp

5 Vapour screen

6 Vapour screen guides

7 Air exit

8 Fairing (supplied in two sizes)

9 Fixing points for cabinet

10 Inspection door for the suction group (ACCESS ALLOWED

ONLY BY A QUALIFIED TECHNICIAN)

Installation - Fig. 5-6

The cooker hood must be placed at a minimum distance of

43 cm from the cooking plane for electric cookers and 65cm

for gas or mixed cookers.

The hood is equipped with a top air outlet B for discharge

of fumes to the outside (Ducting version  exhaust pipe

and pipe fixing clamps not provided).

Where it is not possible to discharge cooking fumes and

vapours externally, the cooker hood may be used in the

filter version by mounting an active carbon filter and the

deflector F on the connection ring placed on the exit

perforation B (Fig. 3), the fumes and vapours are recycled

via the deflector.

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

(not supplied).

Preliminary information for installation of the hood:

Disconnect the cooker hood from the electrical mains during

the electrical connection phase.

The cooker hood is designed for installation inside a wall

cabinet.

It is recommended to install the cooker hood only inside a

cabinet of suitable dimensions.

Do not tile, grout or silicone this appliance to the wall. Surface

mounting only.

Do not fix chimney flue to furniture or fly over shelves unless

the chimney flue can be easily removed, in case maintenance

is ever required.

Refer to figure 2 for useful information for safe installation and

for eventual perforations to perform at the base of the cabinet

for air evacuation, for the

connection cable and to permit to access the electronic card

that controls the cooker hood operation (ACCESS ALLOWED

ONLY BY QUALIFIED TECHNICIAN).

Warning!

The cooker hood is supplied with 4 side spacers (2 for the

right side and 2 for the left side), these are useful when the

width of the housing cabinet for the cooker hood motor body

is wider than 6mm. In this instance the spacers should be

mounted outside the cooker hood body corresponding to the

perforations for the cabinet fixing screws (Fig. 2-A)

1. Measure the cabinet depth (consider also the cabinet

door) as for a depth of up to 315mm will require the

mounting of 37mm fairing, and for measurements over

315mm will require the mounting of 75mm fairing.

The fairing C should be fixed to the cooker hood body

brackets using 4 screws (fig. 3).

2. Fix the air exit connector B above the cooker hood body

(fig. 3).

Only for Filter Version:

place the deflector F on the exit connector.

Fix the filter holder frame inside the cooker hood, firstly

above on the rings R set in the body, then on the base

using the two screws S (fig. 3).

3. Apply the supplied template first to the right and then to

the left (fig. 4.1) or, if supplied, apply the apposite template

to the wall (fig. 4.2  only in case of models conceived

for fixing to the wall) and making holes as indicated (for

the templates for fixing to the wall units 3 dead holes are

indicated, 2 of Ø 2mm and one of Ø 5mm, while for the

template for fixing to the wall, 2 holes of Ø 8mm).

ATTENTION! TEMPLATE AND FIXING TO WALL

UNIT

The lower and back edge of the template must correspond

to the lower edge of the wall unit.

ATTENTION! TEMPLATE AND FIXING TO WALL

The lower edge of the template must correspond to the

lower edge of the hood.

Only for models with fixing hooks: make the holes and

fix two hooks with screws and dowels

(J  fig. 4.2).

Install the two supplied Y brackets with two screws and

washer each onto the upper side of the hood (fig.4.2).

4. Insert the body of the hood inside the wall unit (fig. 5).

This can remain temporarily in position:

a) in case of fixing to the wall unit, using lateral

springs D to imbed into the Ø 5mm dead holes (to do this,

press the lateral springs towards the inside of the body

of the hood using a screwdriver as a liver.

b) in case of fixing to the wall, with the hooks and the

brackets (the bracket have adjustable positioning screws).

ATTENTION!

Check that the electric cable and the smoke outlet are

accessible to facilitate successive connections (and for

technical assistance and maintenance interventions).

5. Check that guides G (fig. 6) are perfectly parallel to the

lower edge of the wall unit, after which, ONLY in the case

of fixing to the wall unit, definitely fix the body of the hood

to the sides of the wall unit with 4 screws (E  fig. 6 

two per side). The screws are to be inserted from

inside the body of the hood on the wall unit in

correspondence with the 4 Ø 2mm blind holes previously

made (see operation 3).

6. Insert the cooker hood cabinet base on the bracket guides

G then carry out the electrical connections of the cooker

hood cabinet base to the casing (fig. 7).

7. Regulate the cooker hood cabinet base in order that the

frontal part is in line with the cabinet (H - fig. 8) then block

the cooker hood cabinet base using 2 screws (one per

side - L - fig. 8  To insert these two screws you will

need to remove the filter grill and screw them on the

inserts that are fixed on the mantel guides).

8. Fix the cooker hood cabinet base to the cabinet using

the 2 screws M (fig. 8), use 2 of 4 perforations available

and check that the screws are fixed to the cabinet.

9. Remount the grease filter, connect the cooker hood to the

electrical network and to the discharge tube, check the

perfect operation of the cooker hood.

INSTRUCTION ON MOUNTING AND USEGB

Elica Glide Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info