Bedienungsanleitung Elica Igloo (Seite 5 von 6) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

471156

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Control panel - Fig. 1 -

a. "ON" indicator light

b. Light ON-OFF button

c. Motor OFF button

d. e. f. Motor speed buttons

speed 1 (d.), speed 2 (e.), speed 3 (f.)

Use of the hood

It is advisable to switch on the extractor

hood a few minutes before starting cooking

and then to leave it running for approximately

5 minutes afterwards to ensure that all odours

are extracted.

Maintenance

Before performing any maintenance

operation, isolate the hood from the

electrical supply by switching off at the

connector and removing the connector fuse.

Or if the appliance has been connected

through a plug and socket, then the plug

must be removed from the socket.

Metal grease filter

The metal grease filter lasts forever and

must be washed either by hand or in the

dishwasher (65°C) with suitable detergents.

The grease filters must be washed at least

once a month.

Let the filter dry without damaging it before

putting it back into place.

When washed in a dish-washer, the grease

filter may discolour slightly, but this does

not affect its filtering capacity.

To remove the metal grease filter - Fig. 2:

1. Disconnect the hood from the electricity.

2. a - push toward the centre

b - pull the filters downwards.

Carry out the above steps in reverse order to

put the filters back after having washed

them.

Carbon filter

(“recirculation mode only”, see next pages)

The carbon filter cannot be washed nor

regenerated.

The carbon filter should be replaced every

6 months under normal use.

To fit the carbon filter - Fig. 3:

1. Disconnect the hood from the electricity.

2. Remove the metal filters.

3. Fit the carbon filter and fix it to the body of

the hood with two supplied screws

4. Put the metal filter back into place.

To replace the carbon filter - Fig. 3:

1. Disconnect the hood from the electricity.

2. Remove the metal filters.

3. Remove the old carbon filter and replace

it.

4. Put the metal filter back into place.

Cleaning

To clean the outside of the hood use a cloth

moistened with denatured alcohol or neutral

liquid detergents. Never use products

containing abrasive.

Wipe brushed stainless steel in the same

direction as the brushing to avoid scratching.

Attention

Failure to observe the instructions for

cleaning the appliance and changing and

cleaning the filters may cause fires.

Therefore, we recommend observing these

instructions.

Replacing the lamp - Fig. 4

1. Disconnect the hood from the electricity.

Firstly check that the lamps are well

cooled prior to replacing them.

2. Unscrew the lamp cover.

3. Replace the damaged lamp with a new

halogen lamp of 20Watt max.

4. Screw the lamp cover on its proper place.

Before calling for repair service because

the hood fails to light up, make sure the

lamps are well inserted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Igloo Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info