Bedienungsanleitung Elica Solaris EDS3 (Seite 8 von 9) (Englisch)

471170

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

in the suction version then it is possible to overturn the upper

section of the chimney

and insert it inside the lower section of the chimney so that the

air-exit perforations are not visible.

The chimneys in which this operation is possible are

recognizable by their bracket fixing points G which are

repeated also in the lower side of the upper section of the

chimney.

Fig. 6

1. Using a pencil, draw a line on the wall, extending up to

the ceiling, to mark the centre. This will facilitate

installation.

2. Rest the drilling template against the wall: the vertical

centre line printed on the drilling template must

correspond to the centre line drawn on the wall, and the

bottom edge of the drilling template must correspond to

the bottom edge of the hood.

3. Place the lower support bracket on the perforation

diagram making it coincide with the traced triangle, mark

the two external holes and perforate. Remove the

perforation diagram, insert two wall-dowels and fix the

support bracket of the hood with two 5x45 mm screws.

4. Hang the hood onto the lower bracket.

5. Adjust the distance of the hood from the wall.

6. Adjust the horizontal position of the hood.

7. Using a pencil mark the cooker hood permanent drill hole

inside the suction group (2 fixing points are necessary for

permanent mounting).

8. Remove the hood from the lower bracket.

9. Drill at the point marked (Ø8mm).

10. Insert 2 wall screw anchors.

11. Apply the flues support bracket G to the wall adherent to

the ceiling, use the flues support bracket as a perforation

diagram (if present, the small slot on the support must

coincide with the line drawn previously on the wall) and

mark two holes with a pencil. Make the holes (Ø8mm),

and insert 2 dowels.

12. Fix the chimney support bracket to the wall using two

5x45mm screws.

13. Hook the hood onto the bottom bracket.

14. Fix the hood into its final position on the wall

(ABSOLUTELY ESSENTIAL).

15. Connect a pipe (pipe and pipe clamps not provided, to be

purchased separately) for discharge of fumes to the

connection ring located over the suction motor unit.

If the hood is to be used in ducting version, the other end

of the pipe must be connected to a device expelling the

fumes to the outside. If the hood is to be used in filter

version, then fix the deflector F to the chimney support

bracket G and connect the other extremity of the pipe to

the connection ring placed on the deflector F.

16. Connect the electricity.

17. Insert the flue into its housing over the hood to cover the

suction unit completely.

18. Fix them above with 2 screws (18a) to the G flues

support bracket (18b).

Additional instructions for the montage

Installing the panel

(number and form of the panels can vary on the basis of the

model)

The panel is supplied dismounted.

Hook the panel onto the pins of the hood and fix with the

supplied latch (the number varies on the basis of the model -

safety-fixing compulsory!).

Rotate the panels to cover the suction area and hook to the

central pin, pressing with decision.

Check that the panel is blocked in position. Fig. 7

Proceed in the same way with the next panel.

Description of the hood

Fig. 1

1. Control panel

2. Grease filter

3. Grease filter release handle

4. Halogen lamp

5. Vapour screen

6. Telescopic chimney

7. Air outlet (used for filter version only)

8. Panel

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Control panel

A. on/off light switch

B. on/off aspiration switch and minimum power selection

B+C. medium power selection aspiration switch

B+D. maximum power selection aspiration switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Solaris EDS3 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info