Bedienungsanleitung Elica Stenna (Seite 14 von 16) (Englisch)

471176

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Functioning - 6-key electronic model

12 34 5F6

1- Motor OFF key.

2- Diminishes the speed.

3- Increases the speed.

4- 5/15 minutes timer. Inserts and extracts the timer.

The speed in function is turned off automatically.

5- Resets carbon filters saturation indicator.

When the F led lights up, the carbon filter should be

cleaned or changed.

Press for at least 3 seconds after having changed the

carbon filter. The F led will turn off to indicate the resetting

of the saturation indicator.

6- ON/OFF light.

If the hood fails to operate correctly, briefly disconnect it from

the mains power supply for almost 5 sec. by pulling out the

plug. Then plug it in again and try once more before

contacting the Technical Assistance Service.

Electronic model with sensor

12 3S

Sensor

Reset

0/I

T1 T2 T3 T4 T51234

T1. Hood On/Off key

T2. Increase cyclical motor speed key.

Pressing the first time activates speed 1. A Led (1-2-3),

corresponding to each speed, switches on. Led 4 flashes

at intensive speed.

After 5 minutes intensive speed is reduced to the second

speed. If key T2 is pressed before the end of the 5

minutes, the hood retunes to the first speed.

T5. Lights On/Off key.

Filter signals

(function active with the hood on): the fats filter signal

appears after 80 hours functioning (Led 1 flashing).

The carbon filter signal appears after 320 hours (Led 2

flashing). In the case of simultaneous signalling of the fats

and carbon filters, Leds 1 and 2 flash alternatively.

Reset filter signals:

press key T4 for 3 seconds until Led 1 switches off (fats

filter). In the case of both filters (fats and carbon)

signalling, repeat the operation just described: pressing T4

the first time switches off Leds 1 and 2 that are flashing

alternatively. Immediately afterwards Led 2 flashes again:

at this point press T4 again for 3 seconds. A beep signals

each time the operation is completed.

Enabling the carbon filter signal:

the hood is enabled only for the fats filter signal. To enable

the carbon filter signal: hood in Off, press keys T2 and T4

for 3 seconds. The flashing of Leds 1 and 2 signals the

completion of the setting. To disenable the carbon filter

signal, repeat this operation again (always with the hood

in Off). A beep signals each time the operation is

completed.

Automatic calibration:

the system carries calibration out automatically about

every 30 minutes (calibration of the parameters

functioning of the sensors).

Manual calibration:

with the hood in Off, press keys T3 and T4 until the beep.

Automatic functioning:

to activate automatic functioning, press key T3: Led 4

switches on. To return to manual functioning, press key

T1, T2 or T3.

Sensors test:

this happens continuously during automatic functioning. In

the case of damage all the Leds flash: in this case, return

to manual functioning, pressing keys T1, T2 or T3.

Selecting cooking top:

this operation optimises the automatic functioning of the

hood: with the hood in Off press keys T2 and T3 for about

3 seconds until the cooking top at present in use is seen:

gas top - Led 1 on

induction top - Led 2 on

electric top - Led 3 on.

Select the cooking top requested pressing T2, then press

T2 and T3 simultaneously for three seconds until the

Beep. Alt the end the hood switches off.

The gas top is the default state.

Attention: carry out this operation the first time the hood

is switched on.

Maintenance

Prior to any maintenance operation ensure that the cooker

hood is disconnected from the power supply.

Cleaning

The cooker hood should be cleaned regularly internally and

externally. Clean using the cloth dampened with neutral liquid

detergent. Do not use abrasive products.

DO NOT USE ALCOHOL!

Warning: Failure to carry out the basic standards of the

cleaning of the cooker hood and replacement of the filters may

cause fire risks.

Therefore we recommend observing these instructions.

Grease filter

Fig. 2

This must be cleaned once a month (or when the filter

saturation indication system – if envisaged on the model in

possession – indicates this necessity) using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle. When washed

in a dishwasher, the grease filter may discolour slightly, but

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Stenna Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info