Bedienungsanleitung Elica stone (Seite 5 von 6) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

132424

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Consult the designs in the front pages referenced in the text

by alphabet letters. Closely follow the instructions set

out in this manual. All responsibility, for any eventual

inconveniences, damages or fires caused by not complying

with the instructions in this manual, is declined.

The cooker hood must be placed at a minimum distance of

50 cm from the cooking plane for electric cookers and 75cm

for gas or mixed cookers.

The hood can be installed above these heights but for

optimum performance it should be installed at the distance

quoted for the appropriate heat source.

The hood is equipped with a top air outlet B for discharge

of fumes to the outside (Ducting version  exhaust pipe

and pipe fixing clamps not provided).

Should it not be possible to discharge cooking fumes and

vapour to the outside, the hood can be used in the filter

version, fitting an activated carbon filter and the deflector F

on the support (bracket) G, fumes and vapours are

recycled through the top grille H by means of an exhaust

pipe connected to the top air outlet B and the connection

ring mounted on the deflector F (exhaust pipe and pipe

fixing clamps not provided).

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

(not supplied).

Installation - Fig. 5-6

Preliminary information for installation of the hood:

Disconnect the hood during electrical connection, by turning

the home mains switch off.

Expansion wall plugs are provided to secure the hood to

most types of walls/ceilings. However, a qualified technician

must verify suitability of the materials in accordance with the

type of wall/ceiling. The wall/ceiling must be strong enough

to take the weight of the hood.

Do not tile, grout or silicone this appliance to the wall.

Surface mounting only.

Remove the grease filter/s.

Remove AND CONSERVE the screws that temporarily

fix the flue units (for reasons of transport), the hood

or the flue unit with the suction unit. The two parts

should be disassembled to facilitate installation. Check how

the parts are fixed together to repeat assemblage at the

opportune moment (see also fig. 6 and operation 17).

1. Using a pencil, draw a line on the wall, extending up to

the ceiling, to mark the centre. This will facilitate

installation.

2. Rest the drilling template against the wall: the vertical

centre line printed on the drilling template must correspond

to the centre line drawn on the wall, and the bottom edge

of the drilling template must correspond to the bottom

edge of the hood: bear in mind that, when installation is

complete, the underside of the hood must be at least 50

cm above the cooker top in the case of electric cookers,

and at least 75 cm above the cooker top in the case of

gas or mixed cookers.

3. Rest the support bracket on the drilling template so that

it coincides with the dotted rectangle, mark the two outer

holes and drill them (mark and also carry out upper drill

holes - 3a), remove the drilling template, insert 4 wall

plugs and fix the hood support bracket into place using

two 5x45mm screws.

4. Hang the hood on the bracket.

5. Adjust the distance of the hood from the wall.

6. Adjust the horizontal position of the hood.

7 Remove the carbon filter frame (see also Fig. 3); mark

the drill hole, using a pencil, for fastening the hood to the

wall.

8. Remove the hood from the bracket.

9. Drill at the point marked (Ø8mm - see operation 7).

Insert 1 wall plug.

10.Rest the chimney support bracket G against the wall,

touching the ceiling. Use the support bracket as a drilling

template (the small slot formed on the support must

coincide with the line drawn on the wall as above 

operation 1) and mark 2 holes with a pencil, dril the holes

(Ø8mm), insert 2 wall plugs. Fix the chimney support

bracket to the wall using two 5x45mm screws.

11.Hook the hood onto the bottom bracket.

12.Fasten the hood to the wall with 1 5x45 mm screw

(ABSOLUTELY NECESSARY), remount the carbon

filter frame (see also Fig. 3).

13.Connect a pipe (pipe and pipe clamps not provided, to

be purchased separately) for discharge of fumes to the

connection ring located over the suction motor unit.

If the hood is to be used in ducting version, the other end

of the pipe must be connected to a device expelling the

fumes to the outside. If the hood is to be used in filter

version, fix deflector F to the chimney support bracket

G using 1 screws, and connect the other end of the

pipe to the connection ring on deflector F.

14.Make the electrical connections.

15.Insert the external covering, of the motor group, half-

way.

16.Make all the electrical connections between the two parts

(for major safety during this operation you may fix the

motor group to the external covering with one screw).

17.Insert the external covering of the motor group fully and

permanently fix with 6 screws.

18.Fix the bracket Z with two screws, so that the bracket

blocks the lower section of the telescopic chimney

(external covering) to the wall.

19.Apply the chimney stacks and fasten them at the top to

the chimney support G (19b) using 2 screws (19a).

Refit the grease filter/s and check that the hood is operating

correctly.

Electrical connection

The electrical tension must correspond to the tension noted

on the label placed inside the cooker hood. Connect the

electrical plug, where provided, to the an easily accessible

outlet in conformity with local standards in force.

Where an electrical plug is not provided (for direct connection

to electrical network) place a standards approved bipolar

switch with an aperture distance of not less than 3mm

(accessible) from the contacts.

INSTRUCTION ON MOUNTING AND USEGB

Elica stone Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info