Bedienungsanleitung Elica tender 90 ix (Seite 7 von 7) (Englisch)

133492

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

icon “Grease filter” is not displayed, and the hood has

the normal display operation.

Charcoal filter saturation alarm (Optional)

• After one hundred and twenty functional hours of the fan,

the display will show “Charcoal Filter” if the fan is active.

When this icon flashes on display, the charcoal filters

installed are required to be replaced or reactivated.

• To reset the charcoal filter saturation indication the user

must press the “-” button for 5 seconds, after this time the

icon “Charcoal filter” is not displayed and the hood has

the normal display operation.

Audible signal activation and deactivation

• The audible signals can be activated or deactivated

pressing the “Light” button for 5 seconds.

• If the audible signal is activated, a tone must sound and

the “Snd” symbol must appear on the display for 3

seconds.

• If the audible signal is deactivated, the “Snd” symbol

must appear on the display for 3 seconds and no tone

must sound.

Charcoal filter inclusion and exclusion (Recirculating

accessories)

• The charcoal filter inclusion or exclusion can be set by

pressing the “+” and “-” buttons at the same time for 5

seconds.

• The Inclusion or exclusion of charcoal filter must be

selected while the lamps and the motor are OFF.

• When the charcoal filter has been excluded, the charcoal

filter alarm is disabled.

Heat sensor

• The control is equipped with a heat sensor that will turn

on the blower at third speed if excessive heat occurs

(over 149° F or 65°C) surrounding the control area.

• If the blower is OFF or if it is operating at first speed, the

blower will be set automatically to third speed, the display

shows the word "CArE" to indicate that heat sensor has

detected an excessive heat.

• During this state, the user may raise the blower speed to

fourth speed but can not decrease the speed.

• When the temperature level on the hood drops to normal,

the blower will operate in the setting defined by the user

before the alarm occured.

Maintenance

ATTENTION! Before performing any maintenance operation,

isolate the hood from the electrical supply by switching off at

the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the

same frequency with which you carry out maintenance of the

fat filters) internally and externally. Clean using the cloth

dampened with neutral liquid detergent. Do not use abrasive

products. DO NOT USE ALCOHOL!

Warning:

Failure to carry out the basic cleaning recommendations of the

cooker hood and replacement of the filters may cause fire

risks.

Therefore, we recommend oserving these instructions.

The manufacturer declines all responsibility for any damage to

the motor or any fire damage linked to inappropriate

maintenance or failure to observe the above safety

recommendations.

Grease filter

Fig. 2

This must be cleaned once a month (or when the filter

saturation indication system – if envisaged on the model in

possession – indicates this necessity) using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

Remove the filter holder frame by turning the knobs (g) 90°

that affix the chimney to the cooker hood.

Charcoal filter (filter version only)

Fig. 3

It absorbs unpleasant odours caused by cooking.

The charcoal filter can be washed once every two months (or

when the filter saturation indication system – if envisaged on

the model in possession – indicates this necessity) using hot

water and a suitable detergent, or in a dishwasher at 65°C (if

the dishwasher is used, select the full cycle function and leave

dishes out).

Eliminate excess water without damaging the filter, then put it

in the oven for 10 minutes at 100° C to dry completely.

Replace the mattress every 3 years and when the cloth is

damaged.

Assembly

Place the mat around the grease filter and fix it in place using

the devices provided.

Position the upper cap and fix it in place using the fixing pin.

To disassemble, perform the steps in the reverse order.

Replacing lamps

Fig. 4

Disconnect the hood from the electricity.

Warning! Prior to touching the light bulbs ensure they are

cooled down.

1. Using a flat head screwdriver or equivalent tool, carefully

pry loose the light cover.

2. Remove the damaged light and replace with a new 12

Volt, 20 Watt (Maximum) halogen light made for a G-4

base SUITABLE FOR USE IN OPEN LUMINAIRES.

Follow package directions and do not touch new light

with bare hands.

3. Reinstall the light cover. (it will snap shut).

If the lights do not work, make sure that the lamps are fitted

properly into their housings before you call for technical

assistance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica tender 90 ix Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info