Bedienungsanleitung Elkron MP110M (Seite 18 von 20) (Englisch)

741486

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

3.6 Disarming with Antirobbery Code

If the system is equipped with an integrated telephone unit or other remote

transmission system, a panic alarm signal can be sent in case of constraint

to disarm the antirobbery system.

• The disarming procedure described in para 3.1 is carried out, but it is

necessary to enter the secret code increasing the last digit by one unit.

• Example: code 123456 would become 123457; code 132459 would

become 132450.

• Disarm the control unit; if within approx.30 sec the correct code is not

entered the control unit will send the panic alarm to all programmed

telephone numbers.

3.7 Wrong Code

• In case of introduction of a wrong code for 4 consecutive times, the

system visualizes a tamper on the keypads and the readers. When

introducing a wrong code for the fifth consecutive time, the system starts

a tamper alarm.

3.3 Arming with Reduced Code

• It is sufficient to enter the first 2 digits of the code followed by key

TOTAL

for a total arming, or

for a partial arming.

• Quick arming is possible only if the system is fully disarmed.

3.4 Commutating Lock with Open Zones

• If the commutating lock with open zones has been programmed, it will

not be possible to arm –neither from keypad nor by DK key – the sectors

to which the currently open zones are associated. If you try such an

arming from keypad, a relevant warning is provided on the display and

no arming will take place.

3.5 Open Zone Self-Bypassing

• If both commutating lock and self-bypassing have been programmed,

the zones left open are automatically bypassed when an arming from

keypad or DK key is carried out. If the arming is made from keypad, the

self-bypassing is properly signalled on the display. The arming regularly

takes place and no alarm is generated. The self-bypassed zones are

reentered automatically at their re-closing (even with armed system).A

following opening will therefore generate the alarm.

Indicates the presence of the mains

voltage and the level of battery charge:

OFF = 220V~ mains absent

FIXED LIGHT = 220V~ mains present

FLASHING = Insufficient battery charge

These display the status of the 3 zones

into which the alarm system is divided:

ON = armed zone

OFF = disarmed zone

These Leds flash to indicate the presence

of events to be displayed, see paragraph

5 “Display of System Status”

Keys used to arm/disarm the system (see

par. “System Arming/Disarming”). These

are also used to scroll the programming

menu.

Keys used to type the secret code and to

select certain functions on the alarm unit

programming menu.

SYSTEM MANAGEMENT BY KEYPAD

WITH SEGMENTED SCREEN

KP100

1.Keypad Description

A flashing light indicates that alarms have occurred.

A flashing light indicates that burglaries have occurred on one or

more parts of the system.

A flashing light indicates that there are some protected zones (doors

or windows protected by contacts) that are still open.

A flashing light indicates that some sensors/contacts are disabled.

TOTAL

ZONE

TEL

EXIT

SIREN

123

KP100

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron MP110M Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron MP110M

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info