Bedienungsanleitung Elro AG400011 - Home Alarm System (Seite 3 von 6) (Englisch)

708646

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

3. You will receive an SMS message saying the phone number was set successfully.

4. Your alarm panel can now be controlled from your phone via app and SMS (Step 9).

1. The alarm panel’s built-in microphone can record your message.

On the alarm panel enter the following:

2. When the record button flashes green, speak into the alarm panel’s microphone to

record a brief alarm message. The maximum length of the message is 10 seconds.

3. When the light stops flashing, the panel will play back the alert message.

Note: Included accessories are pre-binded with the alarm panel at

the factory and ready for use.

1. Test the communication link by pressing disarm on the

remote

2. The red indicator on the remote should light up, and the alarm

panel should sound a long beep.

1. RFID tags can be used to disarm the system.

2. Arm the system using the remote control, ensure that the

ARM icon lights up.

3. Hold the RFID tag near the panel in front of the small hand icon

after arming the system.

4. You should hear a long beep and the disarm indicator should

light up.

5. Several RFID tags can be added and each can have a different number.

1. Put the alarm panel in test mode by inputting:

The disarmed icon will flash when in this mode.

2. Press and release the tamper switch inside the PIR motion sensor (pictured on the right) until

the alarm panel makes a chime sound.

3. Place the rear cover back on the PIR motion sensor.

1. Leave the system in test mode.

2. Press and release the tamper switch on the back of the

sensor until the alarm panel makes a chime sound.

With the "ELRO Home Alarm" app you can remotely access the ELRO

Home alarm system from your smartphone. You can easily disarm and

(partially) arm your alarm system, and receive alert messages on your

smartphone when emergencies occur.

1. On the Google Play Store or Apple App Store, search for “ELRO Home Alarm” and install the

app.

2. Add a new system and choose a name, then enter the phone number belonging to the SIM

card you have inserted into the alarm panel.

3. Select the newly created system from the home screen (Image D below)

4. Then click on the status button to request the current status of the system. (Image E below)

5. A pop-up will appear asking to send an SMS to request the current system status. Select ok.

(Image F below)

6. An SMS with the system status will be sent to your phone. (Image G below)

Step 7 – Testing the PIR motion sensor (SP831)

Step 9 – Smartphone app Setup

Step 4 – Record an alert voice message

Step 5 – Test the remote control (SR401 )

Step 6 – Test the RFID key tag

Step 8 – Test the door / window contact (SM831)

1234

Important: If the siren goes off at any point during the setup, press

the Disarm button on the remote to immediately turn off the siren

Important: Make sure you’re installing the app on the same phone you used in Step 2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AG400011 - Home Alarm System Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AG400011 - Home Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info