Bedienungsanleitung Elro AG40PP (Seite 2 von 3) (Englisch)

708653

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

Less Sensitive More Sensitive A

To mount the unit, first carefully drill out the required mounting holes that are marked on the rear cover

in oval shape. Next, using the rear cover as a template, mark the position of the drilling holes on the

wall. After drilling the holes, attach the rear cover to the wall using the included screws and wall plugs.

Adding the Home PIR Pet-immune Motion Sensor to the AG4000 Home Alarm System:

The alarm panel will group motion sensors and door/window sensors into 5 security types, each

assigned according to when they will be activated:

- Security Type “0”: Fully Armed. The sensor will be activated only when the system is in

Full Arm mode. This sensor will not be activated in Partial Arm mode. When the sensor is

triggered, the alarm will sound immediately without any preset delay.

- Security Type “1”: Partially Armed and Fully Armed. The sensor will be activated when

the system is either fully or partially armed. When the sensor is triggered the alarm will sound

immediately without any preset delay.

- Security Type “2”: Fully Armed + Delay. Same as Security Type “0”, except when the

sensor is triggered the alarm will sound after a preset Entry delay. This is mostly used for the

main entrance to prevent any accidental triggering of the alarm by the user.

- Security Type “3”: Partial Arm and Fully Arm + Delay. Same as Security Type “1” except

when the sensor is triggered the alarm will sound after a preset Entry delay. This is mostly

used for the main entrance to prevent any accidental triggering of the alarm by the user.

- Security Type “4”: 24Hrs intruder: The sensor will immediately trigger an alarm,

regardless whether the system is (partially) armed or disarmed. This is normally used to

protect areas from any unauthorized access, such as a safe box or an electrical maintenance

room, etc.

When a new sensor is added it needs to be assigned to one of the above security types.

To add the sensor:

1. Power on the sensor by inserting its battery.

2. On the alarm panel, enter the PIN + DISARM Key to disarm the system.

3. Enter your PIN + 15 + [security type number] + PARM to start the binding process. The

DISARM LED will start to blink for 30 seconds with a beep tone.

4. Within 30 seconds, set the sensor to enter binding mode using the tamper button shown in the

image on the first page.

5. When the sensor has successfully been added, the DISARM LED will turn on for 1 second

along with a long beep sound. A keypad LED will turn on to indicate the allocated zone number.

(Numbers 1 – 9 for zones 1 – 9, Number 0 for Sensor Zones 10 and above).

6. If the binding process fails, it will timeout after 30 seconds and 3 short beeps will be heard.

7. To exit the binding process, press the DISARM key.

IMPORTANT WARNING:

This package can contain small parts and/or material which can be dangerous to small

children! Be aware of this, and keep this away from small children!

For more information about the ELRO AG4000 Home Alarm System visit

www.elro.eu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AG40PP Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AG40PP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info