Bedienungsanleitung Elro AP5500 - Pro Alarm System (Seite 5 von 49) (Englisch)

708667

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

Through’ will be disabled to allow free access to the

Control Panel to disarm the system before the

entry-delay expires an alarm occurs.

If access is gained via a zone that is not configured as

‘Master Walk Through’, the ‘Slave Walk Through’ zones

will operate as normal according to their programmed

Entry-Delay setting.

Note: A zone set as a ‘Master Walk Through’ zone

must be configured with an Entry-Delay.

OMIT ZONE

A zone may be temporarily omitted when the system is

armed using the Omit feature. When the system is next

disarmed any zones set to Omit will be cancelled.

ZONE LOCKOUT

If a detector on an active zone is triggered while the

system is armed an alarm condition will occur. After

the programmed alarm duration has expired the alarm

will stop and the system will automatically reset.

Subsequent detectors triggered will again initiate an

alarm condition. If a single zone initiates an alarm

condition more than three times then that zone will be

‘Locked Out’ and any further alarm signals from that

zone will be ignored until the system is disarmed.

Note: The ‘Zone Lockout’ feature can be disabled if

required.

EVENT LOG

The Control Panel incorporates a memory capable of

storing the last 50 system events. This enables the

user to see which user has Armed/Disarmed the

system and if and when any alarms occurred. The

time, date and details of the event type will be recorded

for each system event.

CHIME

Chime is a low security facility for use when the system

is Standby mode. If the Chime feature is ON, and a

detector on a zone that has its Chime function enabled

is triggered, the internal sounder will produce a low

volume warning tone. A typical use of the Chime

function would be to warn that a door or particular area

has been accessed.

VOICE DIALER

If the Voice Dialer is enabled and an alarm condition

occurs, the system will call for help using your recorded

alarm messages and up to four telephone numbers.

When an alarm condition occurs, the telephone voice

dialer (if enabled) will call the first enabled number in

the calling sequence and replay the recorded alarm

messages for the configured ‘Play Time’. The recipient

must acknowledge the message by pressing the

button on their telephone keypad. If the call is

unanswered or an acknowledgment is not received

then the next active number in the dialing sequence will

be called. The dialer will continue calling each

number in turn until either all numbers in the sequence

have been dialed the set number of times or the

sequence is cancelled/acknowledged by the recipient.

DIGITAL DIALER

As an alternative to the Voice dialer the system may be

configured to interface with a central monitoring station.

LATCH KEY

When the system is disarmed the Latch-Key facility, if

enabled, will call the first latchkey phone number and

replay the user message (recorded under user setup)

for the set ‘Play Time’. The recipient must

acknowledge the message by pressing the

button on the telephone keypad. If the call is

unanswered or an acknowledgment is not received

then the second latchkey phone number will be called.

The voice dialer will continue calling each number in

turn until each number has been dialed the set number

of times or the sequence is cancelled/acknowledged by

the recipient.

For example, the latchkey facility is useful to inform

parents that a child has returned from school and

disarmed the system.

ANSWER PHONE

The Control Panel includes an answer-phone facility.

The answer phone will record and store a maximum of

6 messages with each message being limited to a 30s

duration.

Messages may be retrieved either direct from the

Control Panel or by dialing into the system from a

phone.

VOICE MEMO

In addition it is also possible to record messages at the

Control Panel using the ‘Voice-Memo’ facility. Each

voice-memo message is limited to a maximum duration

of 30s and counts as an answer phone message.

REMOTE SYSTEM CONTROL

It is possible to dial into the system via the connected

telephone line to interrogate the system status and to

have basic control over the system, (e.g. to Arm and

Disarm the system). You may also activate the

microphone on the control panel to Listen-In to what is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AP5500 - Pro Alarm System Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AP5500 - Pro Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info