483275
33
Zoom out
Zoom in
Vorherige Seite
1/34
Nächste Seite
Default setting: OFF 30s
Scroll through the menu until ‘2-7 Error Beep’ is displayed. The current setting
will also be displayed.
To change the setting press .
Press to enable Warning Beep and enter the required beeping interval in
units of 10s. e.g. enter 6 for a 60s beeping interval (max. setting 25, i.e. 250s)
Press to disable Warning Beep.
ALARM RELAY
This setting controls the operation period for the NO/NC hardwired output relay
contacts following an alarm condition being initiated.
If this is set to ‘ON until Disarm’ then the relay will latch and remain On until
the system is next disarmed.
Default setting: ON until Disarm
Scroll through the menu until ‘2-8 Alarm Relay’ is displayed. The current
setting will also be displayed.
To change the setting press
Scroll through available options, (2s, 30s, 60s, 180s, 300s and ON until Disarm )
until the required setting is displayed and then
Press to save and exit, or
Press to exit without saving.
CALL ABORT
This feature, if enabled, will delay the activation of the telephone dialer following
an alarm for a period of approx. 30s to allow the system to be disarmed.
Default setting: OFF
Scroll through the menu until ‘2-9 Call Abort’ is displayed. The current setting
will also be displayed.
To change the setting press .
Press to enable Call Abort, or
Press to disable Call Abort.
-31-
-34-
Scroll through the menu until ':3 Learning ID2' is displayed.
Three possibilities would happen as follows:
Learning OK - the ID code was learned by the Control Panel successfully.
Time Out - the time involved for learning the ID code is 60s. During this
duration, fail to press the button on the remote control
would result in overdue programming.
ID Duplicate - the same ID code was learned by the Control Panel beforehand.
Scroll through the menu until ':4 Keypad2 Work'
is displayed and press .
Press to enable the Wireless Keypad, or
Press to disable the Wireless Keypad.
ZONE LOCKOUT
This feature, if enabled, prevents a single zone from triggering an alarm
condition more than three times before the system is disarmed. However, if
disabled, there is no limit on the number of times a zone can trigger an alarm
condition.
Default setting: ON
Scroll through the menu until ‘2-15 Zone Lock’ is displayed. The current setting
will also be displayed.
To change the setting press .
Press to enable Zone Lockout, or
Press to disable Zone Lockout.
ENEN
33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

elro-ha68

Suche zurücksetzen

  • Bei meiner HA68 leuchtet permanent eine rote Diode. Heißt das, daß die Akkus im Bedienteil erneuert werden müssen? Eingereicht am 23-8-2022 21:06

    Antworten Frage melden
  • wie kann ich einzelne melder ausschalten? Eingereicht am 19-5-2014 12:38

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Elro HA68 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Elro HA68

Elro HA68 Kurzanleitung - Deutsch - 1 seiten

Elro HA68 Bedienungsanleitung - Deutsch - 34 seiten

Elro HA68 Kurzanleitung - Englisch - 1 seiten

Elro HA68 Kurzanleitung - Holländisch - 1 seiten

Elro HA68 Bedienungsanleitung - Holländisch - 34 seiten

Elro HA68 Kurzanleitung - Französisch - 1 seiten

Elro HA68 Bedienungsanleitung - Französisch - 34 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info