Bedienungsanleitung ELV WS2300 (Seite 4 von 19) (Englisch)

542403

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

GB GB

Setting up using batteries:

Important: To avoid operating problems, please take note of bat-

tery polarity if inserting any batteries

1) Pull away the rain cover of the thermo-hygro sensor to reveal the

three sockets (for the wind sensor, rain sensor and the base sta-

tion)

2) Connect the attached cables of wind and rain sensors to the

corresponding sockets of the thermo-hygro sensor by clicking

them into place

3) Open the battery cover of the thermo-hygro sensor located below

the three sockets and insert 2 x AA, IEC LR6, 1.5V batteries and

close the cover

4) Open the base station’s battery cover located at the back of the

unit and insert 3 x AA, IEC LR6, 1.5V batteries into the battery

compartment and close the battery cover

Setting up using the AC adaptor:

Thermo-Hygro Senso

1) Power up all the sensors as described in setting up using batter-

ies above

2) Using the AC adaptor (included), plug it into the mains outlet and

power up the base station by inserting the adaptor jack into the

6.0V DC socket located on the side of the base station

Every time the thermo-hygro sensor is powered up (for example after

a change of batteries), a random security code is transmitted and this

code must be synchronized with the base station to receive weather

data.

When the base station is powered up, a short beep will sound and all

LCD segments will light up for about 5 seconds before it enters into a

15 minute learning mode to learn the sensors security code. After the

learning mode (or by pressing the MIN/MAX key at anytime), the base

station will start the DCF77 radio controlled time reception.

Note for DCF77 Radio Controlled Time:

The time and date display is based on the signal provided by a highly

accurate Caesium atomic clock operated by the Physikalisch Tech-

nische Bundesamt in Braunschweig (Germany). This radio-controlled

clock does not only provide for the weather station’s time and date

display but also functions as the time source for all of this weather

station’s memory and history values using time and date information.

LCD backlight:

When using the power adaptor, the LCD backlight is switched on

continuously. Under battery operation, the LCD backlight is switched

on for 15 seconds intervals when any key is pressed.

6. Operation using cable connection or wireless 433MHz

Battery

Battery Cove

Compartment

Sensor sockets

Cable Connection:

Using this method of operation will provide interference free transfer

of the weather data from the sensors to the base station. The data

sending interval from the sensors to the base station will also be more

frequent compared to using 433MHz transmission and will result in

higher power consumption. Therefore batteries will have a shorter life

span for cable connection compared to using 433MHz.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ELV WS2300 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info