Bedienungsanleitung Emmeti CS-11 - U9310047 (Seite 2 von 2) (Englisch)

667128

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

To temporary override the current set temperature,

1. Press up or down button once, the set temperature starts flashing

2. Press up or down button again until the temperature you want is displayed

3. Press to confirm the setting with shown on LCD

Now your thermostat will override the current programming and maintain the new set

and hold button for 5 seconds until disappears.

Press button M to select Auto/Manual mode. In Manual mode, the thermostat maintains a constant set

temperature manually set by the user. In Auto mode, the thermostat executes the preprogrammed schedules.

To adjust these schedules, follow the easy steps below,

To set vacation mode press and hold the up button for 5 seconds until appears. Use

same procedure to exit this mode.Vacation mode

up or down button to change the set point and wait for 5

will maintain a set temperature(default

Your thermostat has the ability to reset all settings to the factory defaults. If you are

certain you want to do this: In standby mode(when thermostat is turned off), press

If thermostat is set in AF model, press and hold the down button for 5 seconds,

floor temperature will show and it will automatically revert back to room temperature

This product should be installed by

a qualified electrician.

Installation and Wiring

86mm

mm68

Rear View

45mm

13mm

27 mm

26 m

Side View

60mm

mm68

86mm

4mm

mm7

LOAD

(16A)

(220VAC+/-15%)

Floor Sensor

(or remote air sensor)

To lock the buttons, press and hold the up and down buttons for 5 seconds until you

see a lock icon appearing, to unlock, repeat the steps above.

and hold

button M and for 5 seconds until “RES” is shown for 5 seconds on LCD.

This thermostat is fitted with a real time clock. It is essential that the clock time and day

are set accurately if you require your programmed events to start on time. Follow the

Set the Time and Day

Auto / Manual Mode

Program your thermostat

Resetting factory defaults

Lock the buttons

View floor temperature

Temporary temperature override

Vacation mode

Press the button once

Use up or down button to change the time (Hold up or down button to change

Press button again, the day of the week will flash

Press button again to accept and exit

Use up or down button to change the day of the week

Press and hold button M for 5 seconds until “Program” is shown with the Day flashing. Use up or

down button adjust the day (hold up or down button for 5 seconds to set all days the same).

Press button M again and use up or down button to set the desired temperature to be

Press button M to bring up the program 1. Use up or down button to set the start time

To skip program 2 ,3,4,5 for Saturday and Sunday, simply adjust the set temperature for program

To skip program 3 and 4, simply adjust the set temperature for program 3 and 4 to the same set

temperature as program 2.

2 ,3,4,5 to the same set temperature as program 1.

and the time will flash Step 1.

Step 2.

Step 3.

Step 4.

Step 5.

°C

) all the time. Press

Carefully separate the front half of the thermostat

from the back plate by placing a small flat head

terminal driver into the slots on the bottom face of

the thermostat

Carefully unplug the ribbon connector

which is plugged in to the front half of

the thermostat

Place the thermostat front half somewhere

safe. Terminate the thermostat as shown

in the diagrams below

Screw the thermostat back

plate on to the back box

Re-connect the thermostat ribbon cable

and clip the two halves together

(default 06:30).(Hold up or down button to change by 15 minutes each time.)

Programme Start time Setpoint

maintained for program 1.(default 21

°C

)

below easy steps,

by 15 minutes each time.)

seconds to accept and exit.

temperature until the next program period begins. To cancel the override setting, press

in 5 seconds.

CS-11 LCD 7-Day 5+2 Programmable Digital Thermostat

U9310047

Wiring Diagram

123456

SWL

Sensor

Remote

out used

Single Zone

Multi Zone

Not

Neutral

230V AC

Registered Address: 6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW

Tel: 01993 824900 : www.emmeti.co.uk : e: sales@emmeti.co.uk

“ Temporary ”

Repeat and unitl you finish the settings for 6 programmes. Press

button M to accept and exit.

The below is the default factory settings for the 6 programmes.

2 3

06:30

08:30

11:30

13:00

16:30

22:30

21°C

16°C

21°C

16°C

Note: It is faster to program the same schedule for the entire week and then to adjust the exceptional days.

1. Please ensure that the electrical wiring of the installation and connections to and from the thermostat and any remote sensor connected to it are in accordance with BS 7671, the latest edition of the IET

Wiring Regulations.

2. The thermostat must be wired to the electric mains through a switch capable of disconnecting all poles compliant with the current safety standards and with a contact separation of at least 3 mm in all poles.

3. Before commencing work on the installation, the electricity supply must be disconnected.

4. The depth of the back box should be 35mm minimum.

WARNING

Dimensions

ErP Class

+1%

ErP Class

+5%

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emmeti CS-11 - U9310047 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info