Bedienungsanleitung Emmeti CS-11 - U9310090 (Seite 1 von 1) (Englisch)

667127

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

U9310090

Your thermostat has the ability to reset all settings to the factory defaults. If you are certain you want

to do this: In standby mode(when thermostat is turned off), press and hold button and

for 5 seconds until RES is shown on LCD.

Configure the menu

Resetting factory defaults

Setting temperature

Press or once, you will see set temperature flashing. Use or again to adjust

to the temperature you want your room to maintain. Press button to accept and exit.

Buttons and LCD display

Buttons Press < 5 seconds Press > 5 seconds

Turning on/off thermostat

Menu button

Increase the set value

Decrease the set value

Lock /unlock buttons

Reset to factory settings

(when thermostat is turned off)

Confirm settings

The buttons are locked.

Displays when heating is active

Setback mode

Symbol Description

Set temperature

Set At

Sensor selection. This thermostat is a combination model allowing you to choose

between 3 different models. (A, AF,F )

model: air onl

y, with built in sensor

AF model: air & floo r , with both built in and remote sensor

F model: floor only, with remote sensor

Press and hold button for 5 seconds. Now you can see Menu 01, to proeceed to other menu, press button again. To exit menu, press button

First turn off the thermostat using the on/off button

Menu #

Switching differential.

Calibrate the room temperature. This feature is used to compensate for any difference

Calibrate the floor temperature. This feature is used to compensate for any difference

Set the floor temperature limit.

Select temperature format

Feature Description

Factory Default

Feature Value

°C

4°C

10°C

35°C

2°C~ 7°C

10°C~ 20°C

20°C~ 35°C

°C ~

°C

°F

°C

A / AF / F A

Press or to select

The numbers of degree difference before switching.

between the displayed room temperature and a thermometer.

between the displayed floor temperature and a thermometer.

This feature is to protect the floor surface.

°C or °F.

The default is 1°C which means the thermostat will switch the

heating on

0.5°C below the set temperature and will turn it off 0.5°C above the set temperature.

With a 2°C differential,

the heating will switch on 1°C below the set temperature

and will switch off 1°C above the set temperature.

1°C 1°C ~ 5°C

-5°C ~ +5°C

°C

-5°C ~ +5°C

Installation and Wiring

Carefully separate the front half of the thermostat from the back plate by placing a

small flat head terminal driver into the slots on the bottom face of the thermostat.

Carefully unplug the ribbon connector which is plugged in to the front half of the thermostat.

Place the thermostat front half somewhere safe. Make the wiring connections as

Screw the thermostat back plate on to the back box.

shown in the diagram below.

Re-connect the thermostat ribbon cable and clip the

CS-11 LCD Digital Setback Thermostat

Frost protection. This is to avoid room temperature goes below 5°C.

The setback amount( the amount of temperature reduction)

on / off off

Switched live

output

230V ~ 50Hz

L N

Link terminals 1

to 3 for 230VAC

live output

Remote sensor for ﬂoor

temperature control

Timeswitch live

for operaon

of temperature

setback mode



Registered Address: 6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW

Tel: 01993 824900 : www.emmeti.co.uk : e: sales@emmeti.co.uk

This gives you the option to limit the minimum set temperature

This gives you the option to limit the maximum set temperature

1. Please ensure that the electrical wiring of the installation and connections to and from the thermostat and any remote sensor connected to it are in accordance with BS 7671, the latest edition of the IET

Wiring Regulations.

2. The thermostat must be wired to the electric mains through a switch capable of disconnecting all poles compliant with the current safety standards and with a contact separation of at least 3 mm in all poles.

3. Before commencing work on the installation, the electricity supply must be disconnected.

4. The depth of the back box should be 35mm minimum.

WARNING

Please Note: one of the following error messages will appear if one of these problems occur:

E0, meaning the internal sensor is broken, short-circuit or not working properly.

E1, meaning the floor sensor is broken, short-circuit, not connected, or not working properly.

Single Zone

Multi Zone

ErP Class

+1%

ErP Class

+5%

two halves together.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emmeti CS-11 - U9310090 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info