Bedienungsanleitung Emmeti CS-11- U9310020 (Seite 1 von 1) (Englisch)

667126

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

U9310020

Your thermostat has the ability to reset all settings to the factory defaults. If you

are certain you want to do this:

In standby mode(when thermostat is turned off), press and hold button

and for 5 seconds until RES is shown on LCD.

Set the Time

Configure the menu

Resetting factory defaults

Setting temperature

1) Press and hold button until the time flashes

2) Use button or to change the time

3) Press button to accept and exit

Press or once, you will see set temperature flashing. Use

or again to adjust to the

temperature you want your room

to maintain. Press button to accept

and exit.

Buttons and LCD display

Buttons Press < 5 seconds Press > 5 seconds

Turning on/off thermostat

Menu button

Increase the set value

Decrease the set value

Lock /unlock buttons

Reset to factory settings

(when thermostat is turned off)

Set the time

Confirm settings

The buttons are locked.

Displays when heating is active

Symbol Description

Set temperature

Set At

Sensor selection. This thermostat is a combination model allowing you to choose

between 3 different models. (A, AF,F )

model: air onl

y, with built in sensor

AF model: air & floo r , with both built in and remote sensor

F model: floor only, with remote sensor

Press and hold button for 5 seconds. Now you can see Menu 01, to proeceed to other menu, press button again. To exit menu, press button

Menu #

Switching differential.

Calibrate the room temperature. This feature is used to compensate for any difference

Calibrate the floor temperature. This feature is used to compensate for any difference

Set the floor temperature limit.

Select temperature format

Feature Description

Factory Default

Feature Value

°C

°C ~

°C

°F

°C

A / AF / F A

Press or to select

The numbers of degree difference before switching.

between the displayed room temperature and a thermometer.

between the displayed floor temperature and a thermometer.

This feature is to protect the floor surface.

°C or °F.

The default is 1°C which means the thermostat will switch the

heating on

0.5°C below the set temperature and will turn it off 0.5°C above the set temperature.

With a 2°C differential,

the heating will switch on 1°C below the set temperature

and will switch off 1°C above the set temperature.

1°C 1°C ~ 5°C

-5°C ~ +5°C

°C

-5°C ~ +5°C

Installation and Wiring

Carefully separate the front half of the thermostat from the back plate by placing a

small flat head terminal driver into the slots on the bottom face of the thermostat.

Carefully unplug the ribbon connector which is plugged in to the front half of the thermostat.

Place the thermostat front half somewhere safe. Terminate the diagrams below.

Screw the thermostat back plate on to the back box.

Re-connect the thermostat ribbon cable and clip the two halves together.

CS-11 LCD Digital Thermostat

Registered Address: 6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW

Tel: 01993 824900 : www.emmeti.co.uk : e: sales@emmeti.co.uk

Frost protection. This is to avoid room temperature goes below 5°C. on / off off

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Emmeti CS-11- U9310020 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Emmeti CS-11- U9310020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info