659300

Enda ET2011 PID Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
SET
SET
C.s.lo.= Control set point lower limit.(for
selected output)
Adjustable between 0 and C.s.Hi.
C.s.Hi.= Control setpoint upper limit.(for
selected output)
Adjustable between C.s.Lo. and Upper scale
value.
a2.s.l= Alarm2 set value lower limit.
Adjustable between 0 and A2.S.H
parameter value.
a2.s.H= Alarm2 set value upper limit.
Adjustable between A2.S.L
parameter value and upper scale
value.
a2.Hy = Hysteresis of the Alarm2
output.
Adjustable between 1 and 50 °C.
A2.st. = The state of Alarm2 output.
Hi = If A2 output is above the set
value. (on)
lo = If A2 output is above the set
value (off).
A2.Er. = State of Alarm2 output in the
case of sensor failure.
on = A2 output is probe failure (on).
off= A2 output is probe failure (off).
A2.tp = Function of Alarm2 type.
Four kinds of functions can be
selected.
indE. = Independdnt alarm
(Independent)
dE. = Deviation
bAnd = Band alarm (Band)
bAn.i = Band with inhibition
inp.t. = Input type selection.
Pt.0 = PT100 Decimal,
Pt = PT100,
FE.cn.= J type,
nc.nA.= K type,
c.cn. = T type,
p10.r.= S type,
P13.r.= R type thermocouple selection.
This parameter varies when changing
some parameters.
Unit = The temperature unit.
°C = °C, °F= °F
(This parameter varies when
changing some parameters.)
C.o.sE = Control output selection
C-A2 = C/A2 (Relay) output selection
SSR = SSR output selection
F.kE.C. = Function key setting parameter
nonE = Function key is off.
C2.S.A. = The function key with 2.set value is used.
manu. = Manual mode can be achieved with the function key.
dSP.o. = Only the temperature display mode is entered with
function key.
C. Pb = Proportional band.(for selected
output)
Adjustable between %0.0 and %100.0.
C. Pb = %0.0,On-Off control is selected.
C. ti = Integral time.(for selected output)
Adjustable between 0 and 100.0 minutes.
C. ti = 0.0,integral impact is disable.
parameter is different from “0”,this
parameter appears.
C. Pb
C.Hys = Hysteresis of the output.(for
selected output)
Adjustable between 1 and 50 °C.
= 0,this parameter is active.C. Pb
C. td = Derivative time.(for selected output)
Asjustable between 0.00 and 25.00 minutes.
C. td = 0.0, derivative time is disabled.
parameter is different from”0”,this
parameter appears.
C. Pb
C. Ct. = Period time.(for selected output)
Adjustable between 1 and 250 second.
parameter is different is different
from“0”,this parameter appears.
C. Pb
C.p.st = The ratio of output power at the
setpoint.Adjustable between %0 and %100.
C.E.P.s. = The percentage of faulty sensor
selected output power.
Adjustable between %0 and %100.
C.typ. = Control output type
C.typ. = HEAt means heating control.
C.typ. = CooL means cooling control.
While the parameter names appear, if and
keys are pressed together, returns to the program mode.
S.Cod = Security menu access
code.
It should be 2011.
Cosc. = Parameters of CoN.o.
menu security access level code.
nonE = Invisible.
P.yEs = Modification can be done.
P. no = Only visible.
m.SEt. = The percentage of manual output parameter.
Adjustable between %0 and %100.
This parameter allows manual adjustment of the output
power when the manual output selection.
C. Pb.= 0, this parameter is not seen.
If co.SE parameter is different
from C-A2, this parameter is seen.
a.2.sc. = Parameters of al2.o.
menu security access level code.
nonE = Invisible.
P.yEs = Modification can be done.
P. no = Only visible.
Co.sc. = Parameters of Conf.
menu security access level code.
nonE = Invisible.
P.yEs = Modification can be done.
P. no = Only visible.
S.t.Sc. = Parameters of S.tun.
menu security access level code.
nonE = Invisible.
P.yEs = Modification can be done.
Co.sc. = Parameters of Conf.
menu security access level code.
no = Parameter settings are not
change.
yEs = Parameter setting will be
restored.
2/4
C.s.Lo.
C.s.Hi.
C. pb
C. ti
C. td
C.p.st
C.Hys
C. Ct.
C.typ
s.s.t.s.
C.E.p.s.
Con.o.
AL2.o.
ConF.
S.tun.
SEcu.
S.Cod.
Co.sc.
m.SEt.
a.2.sc.
Cn.sc.
S.t.sc.
dEF.P.
inp.t.
Unit
fltr.
C.o.sE
offs.
s.t.Co.
F.k.E.C.
A2.S.L
A2.S.H
A2.HY
A2.tP
A2.St.
A2.Er.
SET
SET
SET
SET
SET
F
Programming mode
This parameter indicates the time to reach set point
value when the device is first energised.
Adjustable between 0 and 250 minutes.
If 0 is selected, soft start feature will be enable and the
device reaches set point value quickly.
Setting Pb = 0, soft start feature will be disabled.
Sst.S =Sofy starter timer set value
fLtr. = Coefficient of digital filter.
Filter for display value.
Adjustable between 1 and 200. If this parameter is 1,
digital filter runs most quick. If the parameter is 200,
the filter run most slow. The value of parameter should
be increased in interference.
oFfS. =
Offset value is added to the measurement value.
Adjusted between -100 and +100°C.The normal value is 0.
Offset value.
St.Cu = Self tune control parameter.
If both keys are pressed ,yEs
message is displayed on the screen
and selftune process is started
automatically.
If both keys are pressed, no
message is displayed on the screen
and selftune process is stopped.
SET
If key is pressed while holding key, the programming mode is enabled.
SET
F
Entering from the programming mode to the run mode:
If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered.
Alternatively, the same function occurs first pressing key and key is pressing programming mode is entered.Then and keys are pressing
together, data is recorded and running mode is entered.
Modification Of Parameter Diagram
When holding key, the value of parameter flashes and using
keys the requested value can be adjusted.
If key is pressed and held 0.6 seconds, the value of the selected
parameter changes rapidly. If waited enough,the value increases 100 at each
step. After 1 second following the release of the key, initial condition is
returned.The same procedure is valid for the decrement key.
Chys
6
5
6
SET
SET SET
SET
C.s.lO.
inp.t.
A2.s.l
Co.sc.
C1.sE.
C.s.Hi.
Unit
A2.s.H
A2.Sc.
C2.SE.
C. PB
Fltr.
A2Hy.
Cn.Sc.
A2.SE.
C.HyS
C.o.SE.
A2.tp
S.t.Sc.
C. ti
offs.
a2.st.
dEf.P.
C. td
f.k.E.C.
a2.Er.
a2.Er.
C. Ct.
m.sEt.
C.P.St.
C.EP.S.
S.s.t.S.
C.typ.
TC input
TC input
TC input
TC input
TC input
PT100 input
PT100 input
PT100 input
PT100 input
PT100 input
0
FE.cn.
0
0
25
2
2
C-A2
indE
P.yEs
P.yEs
400
P.yEs
400
P.yEs
500
4.0
0
Hi
no
1.00
nonE
on
no
20
50
0
0
0
HEat
-200
Pt.
-200
600
°C
600
DEFAULT PARAMETERS
Set parameters
Control output
parameters
Alarm2 output
parameters
Configuration
parameters
Self tune
parameters
Security
parameters
SET
SET
ET2011-E-06-201408
When the self tune begins,
PIdt. message
and measurement value are shown
alternately.
After the completion of the self tune process,
st.Co. parameter is automatically changed to
no and the device returns to working mode.
If the measured temperature is higher than
90% of the set value at the beginning of the
self tune process, then tE.Hi. message is
shown alternately and the measured
temperature is waited to go below %60 of
the set value. After that, self tune operation
is started automatically.
If it is intended to abort the self tune
process, St.Co. parameter is changed to
no and key is pressed.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Enda ET2011 PID wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Enda ET2011 PID

Enda ET2011 PID Bedienungsanleitung - Deutsch - 4 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info