Bedienungsanleitung Engenius ECB1750 (Seite 1 von 2) (Englisch)

619951

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Quick Installation Guide

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wiabc.com

Disclaimer: Information may be subject to changes without prior notication.

https://www.linkedin.com/company/engeniuseurope

https://plus.google.com/+EngeniusEuropeBVDeMeern

https://www.youtube.com/user/engeniuseuropebv

https://twitter.com/engeniuseu

ECB1750

Package content

Unpack the box and verify the content:

- ECB1750

- RJ-45 Ethernet-cable

- 12V/1A 100V~240V Power adaptor

- 3*2.4GHz detachable antenne

- 3*5GHz detachable antenne

- Quick Installation Guide

- CD with instruction manual

Minimum requirements

- Broadband Internet Service (Cable or DSL modem)

- Internet browser (Internet Explorer, Safari, Firefox, Chrome)

Hardware installation

1. Please install the antennas as shown below.

2. Connect one end of the Ethernet cable into LAN port of the ECB1750 and

the other end to the computer that will use the ECB1750. Ensure that the cable

is securely connected to both the ECB1750 and the computer.

3. Connect the power adaptor DC inlet to the DC-IN port of the ECB1750 and

the power adapter in to the electrical outlet.

Note: The ECB1750 supports

both IEEE 802.3at PoE (power

over Ethernet) and regular

power adapter. You should

use either one as the power

source. Please do not apply

both at the same time.

Computer setup

1. After ensuring the EnGenius device is powered on and plugged in, ensure

that your computer is on.

2. For the next steps, refer to your operating system user manual.

3. Once your computer is on, ensure that your TCP/IP is set to ON or

ENABLED. In the control panel, double click network connections and then dou-

ble click on the connection of your Network Interface Card (NIC). Select Internet

Protocal (TCP/IP) and then click on the properties button.

4. If your PC is already on a computer network, ensure that you have set it to

a Static IP adress on the interface (or Ethernet card that will use the ECB1750).

Set it as 192.168.1.21 and the subnet mask address as 255.255.255.0.

Select ‘Use the following IP address’-radio button. Once the computer has been

prepared, proceed to setting up the ECB1750.

EAP1750 setup

1. To configure ECB1750, open a web browser (example: Microsoft Internet

Explorer, Mozilla Firefox, Google Chrome, etc.)

2. In the adress bar of the web browser, enter: 192.168.1.1 (the default IP

address of the ECB1750) and hit ENTER.

3. A login screen will appear. By default, the username of the ECB1750 is

admin and the password is admin. Enter the current username and password

of the ECB1750 and then click ‘Login’. Refer to the ECB1750 user manual on

how to change the username and password.

4. After clicking ‘Login’ with the correct username an password, the ECB1750

main menu will appear. If you are successful, proceed to setting up the wireless

connection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Engenius ECB1750 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Engenius ECB1750

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info