Bedienungsanleitung Entrematic Superior plus 42 TOF (Seite 21 von 24) (Alle Sprachen)

680496

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

CHECK THE GARAGE OPENING

Check opening measurements A (width) and B (height) to

ensure you have the correct size of door for the opening.

CHECK THE FLOOR LEVEL

Use the spacer bar and spirit-leveller to ensure the bot-

tom of the wall-tracks are level and that the position of

the door will be centred in the opening. The spacer bar is

supplied to the width required between the tracks.

On the floor of the garage, assemble the wall-tracks for

both right and left hand sides (1-3), by using 3 track

screws and collar nuts per track, tighten the nuts in shown

order

(2, 3)

IMPORTANT: It is essential that the wall tracks are

installed level,square and flush to achieve the correct door

operation.

Clamp the right side wall-track to the opening (1); ensur-

ing the track is at the correct height from the floor. Use the

spacer bar to establish the position of the right hand track,

relative to the left side, to ensure the door will be central

the opening. (2)

Use a spirit-leveller to ensure the track is vertical. (3)

Drill and fix the track with two 50mm screws and wash-

ers, in the centre of slot-hole.

Use only 1 screw in the bottom and 1 screw in the middle

of the wall track to allow for later adjustment (4). Do not

yet enter the screws in the upper wall track profile.

Drill: Timber = Ø 3,0 mm, no plugs required

Steel = Ø 5,5 mm, no plugs required

Concrete, bricks = Ø 10,0 mm, use the blue plugs

Make sure to insert the plugs according to sketch to avoid

cracking of the wall. (5)

An alternative way of fixing the wall tracks is to use side

brackets (option) for behind and inside the reveal (alt-

hough this will require 40 mm extra side-room), which

allows for adjustment of the wall track in all directions.

Pre punched holes for brackets in the wall track.

Apply the top rubber sealing to the lintel profile (1)

Click the centre clip in place, off centre by approximately

100-150mm.

(2)

Insert a lintel end bracket at each end of the lintel (3)

Hook the lintel beam on to the wall-tracks, using the slot

at the top of the end bracket. (4)

Start to assemble the ceiling track parts by using 2 x track

screws and collar nuts (1).

Put the angle steel above the joint and then fix by 4 x

track

screws and collar nuts (2). At the rear end of the

ceiling-tracks use the 12 mm screws (3)

Place the ceiling tracks at a 90º angle to the floor (5). This

will give you an approximate position to fix the L-angle

track support to the ceiling.

Fix

the ceiling profiles approx. 200 mm inside from the

ceiling track with 2 x 50 mm screws. (6)

Install the L-profile hanger with one coach-bolt M-8 and

a collar nut at the approximate end position of the ceiling

track. (7)

Fix the two spacer bar clips to the hanger L-profile at the

approximate height of the door (one for each track), with

coach-bolt M-8 and collar nuts. (8)

Clamp the left hand track to the wall opening. (1)

Use the spacer bar at the bottom to position the left track,

relati

ve to the right hand track. (2)

Drill through the bottom hole and insert a 50mm screw

and washer in the centre of the slot-hole. (3)

Fix the clips to the two ‘L’ shaped ceiling hangers and to

the

spacer bar, using coach-bolt M-8 and collar nuts with-

out tightening the nuts (1) (At this stage, the spacer bar

does not need to be in its final position. It will be tighte-

ned later). Hook the ceiling-tracks to the wall-track hooks

(2). Hook the ceiling-tracks on to the distance beam by

placing the rear end of the right hand ceiling track to the

spacer bar, fix with a collar nut (3) Fix both ends of the

lintel to the wall-tracks (4). If TORSION REAR, fix the

corner plate by sliding the plate on to the track (5) then

put in the track screw (6) from outside and then the nut. If

TORSION FRONT position track screws in top hole from

outside the track. Use collar nuts. (5)

(Do not tighten the nuts (4, 5) the movement is of

use when fitting the curve. without tightning the nut.)

Complete the fixing of the wall tracks in the centre of the

slotted holes to the wall by 50mm screws and washers (7).

Fix the centre clip (and the centre support bracket (9), if

the door has a TORSION FRONT balancing system, by 2

x 50 mm screws, including washers. (8)

Move the spacer bar up to the top of the wall track, into

the slot-holes in both right and left hand tracks. This gives

the correct distance between the wall tracks at the top. (1)

Drill and fix the left hand track with one 50 mm screw in

centre of the slot-hole, (as previously done on the right

hand side track).

Remove the spacer bar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Entrematic Superior plus 42 TOF Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info