Bedienungsanleitung Entrematic Superior plus 42 TOR (Seite 23 von 24) (Alle Sprachen)

680495

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Daylight

opening (B) 1900 2000 2125 2250 2375 2500 2650 2800 3000

No of turns 6,6 6,9 7,3 7,7 8,1 8,5 9,0 9,5 10,1

19.

CAUTION: When torsion front balanced, exchange the

Allan screw for a longer screw and put on the conical

guide, right and left side. (1)

The guide will protect the door cable from being damaged.

Fix

the pre-assembled top roller by 5 panel screws. (2)

18.

CAUTION: Position a clamp to one side to support the top

section. (1)

Put the top section in position (the top section is 65 mm

shorter

than the other sections). (2)

ATTENTION: Start to put in all the hinges NOTE: The

hinge-part when fixed into the panel must have the lubri-

cation hole visible

(If not the hinges are upside down ).

Ensure that the sections are correctly positioned sideways.

(3)

Complete the fixing of side hinges. (4-7)

Repeat for left hand side.

Fix all mid hinges. (8)

Put the cable guide into the bottom of end cap, right and

left side of bottom section. (1)

Put the spring on the shaft and give the shaft some oil. (2).

Slide the door cable on to the roller shaft. (3)

Turn the rollers into the wall track and fix the bottom

bracket to the section using 5 x panel screws.

ATTENTION: Use the upper hole (4), not to damage the

cable guide.

Repeat for the left hand side.

Take the door cable to the right and the left drum (2), and

fix the cables on to the drum. (3).

Wind up the door cables, running between the spring

holding bracket and the drum, by turning the shaft.

Tension the spring 1/2 a turn (to keep the door cable

stretched). (4).

Tighten one screw (temporary) on shaft coupling to the

shaft (5). Repeat for left hand side.

16.

Lift the panel and take away the two supports, and then let

the panel down to the ground carefully. (1)

Check that the door-cables are positioned correctly on the

cable

guides (2), at the bottom roller holders and behind

the mid roller shafts(2). Check that the panel section hangs

centrally between the tracks.

Put the 1st midsection in place (with the handle hole). (3)

If the door has no handle, use the ”bottom” section (the

first section in the package).

Slide in the mid-rollers right and left. (4)

If the door has handle, insert the handle from outside , the

lock mechanism from the inside and tighten the screws

(5). Pull down the “plate” (6) so the holes be free ,drilling

2mm holes and tighten the screws (7)

17.

Put the 2nd mid-section in place. Slide in the mid-rollers

on the right and left hand sides.

Put the remaining mid sections in place (the number of

sections depends on the door height) (1-3), but do not put

the top section in place (the top section is 65 mm shorter

than other sections).

15. TOR

Hang the doorcable over the pulley wheel, slide the pulley

wheel cover in position and fix

with two panel screws (1-4).

Take the door cable to the right and the left drum (3), and

fix the cables on to the drum (4).

Wind up the door cables, running between the spring hold-

ing bracket and the drum, by turning the shaft.

ension the spring 1/2 a turn (to keep the door cable

stretched) (5).

Tighten one screw (temporary) on shaft coupling to the

shaft (6).

Repeat for left hand side.

Put the cable guide into the bottom of end cap, right and

left side of bottom section. (7)

Put the spring on the shaft (8), and give the shaft some oil.

Slide the door cable on to the roller shaft. (9)

Turn the rollers into the wall track and fix the bottom

bracket to the section using 5 x panel screws.

ATTENTION: Use the upper hole (10), not to damage the

cable guide.

Repeat for the left hand side.

Store the spring bars in the lintel profile for future use.

Tighten the spring-retainer using the two screws to the

shaft (spring by spring). (3). Oil the springs (4).

Tighten the shaft coupling to the two shaft parts. (1)

Check that the shafts meet in centre of shaft coupling.

Max gap between shafts = 10 mm.

Wind up the spring according to stated number of turns

belo

w. (2)

20.

21.

Open the door fully. Be aware of the area the door moves

through and ensure people and objects are out of the way

If the door has an Assa/KABA cylinder, must the existing

cylinder changes , see separate instruction in the cylinder

bag.

15. TOF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Entrematic Superior plus 42 TOR Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info