Zoom out
Zoom in
Vorherige Seite
1/130
Nächste Seite
User’s Guide
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    User’s Guide



  • Page 2

    Notations Used in This Guide
    • Safety indications
    The documentation and the projector use graphical symbols to show how to use the projector safely.
    Please understand and respect these caution symbols in order to avoid injury to persons or property.

    Warning

    This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

    Caution

    This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

    • General information indications

    Attention

    q

    Indicates procedures which may result in damage or injury if sufficient care is not taken.
    Indicates additional information and points which may be useful to know regarding a topic.

    s

    Indicates a page where detailed information regarding a topic can be found.

    g

    Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
    section of the "Appendix". s p.125

    Procedure

    Indicates operating methods and the order of operations.
    The procedure indicated should be carried out in the order of the numbered steps.

    [ (Name) ]

    Indicates the name of the buttons on the Remote Control or the Control panel.
    Example: [ESC] button

    "(Menu Name)"
    Brightness (Boldface)

    Indicates the configuration menu items.
    Example:
    Select "Brightness" from the Image menu.
    Image menu - Brightness



  • Page 3

    Contents

    3

    Notations Used in This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . 2
    Introduction

    Limitation of the Number of the Target Projectors when Using
    Multiple Projectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

    Projector Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
    Ease of use when installed on a ceiling mount. . . . . . . . . . . . . . . . . . . . . . .
    Reliablity you can depend on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Large Projection Area and Precise Colors. . . . . . . . . . . . . . . . . . . . . . . . . .
    Enhanced security functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Easy to handle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Using the projector over a network (EB-Z8050W only). . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .

    7
    8
    8
    8
    8
    8

    Part Names and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
    Front/Top. . . . . . . . . . .
    Interface. . . . . . . . . . . .
    Rear. . . . . . . . . . . . . . .
    Remote Control. . . . . . .

    Changing the Aspect for computer images. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
    Pointer Function (Pointer). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
    Enlarging Part of the Image (E-Zoom). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    10
    11
    12
    13

    Useful Functions
    Correcting Distortion in the Projected Image. . . . . . . . . . . . . . . . . . 17
    Correcting Distortion with Quick Corner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

    Changing the Projected Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
    Automatically Detect Input Signal and Change the Projected Image (Source Search)
    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
    Switch to the target image by Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . 22

    Functions for Enhancing Projection. . . . . . . . . . . . . . . . . . . . . . . . . . 23
    Selecting the Projection Quality (Selecting Color Mode). . . . . . . . . . . . . . .
    Setting the Auto Iris. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Hiding the Image Temporarily (Shutter). . . . . . . . . . . . . . . . . . . . . . . . . .
    Freezing the Image (Freeze). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Changing the Aspect Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Changing methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Changing the Aspect for video equipment images. . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    23
    24
    24
    24
    25
    25
    25

    Setting the Projector ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
    Checking the Projector ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
    Setting the Remote Control ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

    Correcting Color for Multiple Projectors (Multi-Screen Color
    Adjustment). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
    Summary of Correction Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
    Correction Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

    Security Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
    Managing Users (Password Protect). . . . . . . . . . . . . . . . . . . . . . . . .
    Type of Password Protect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Setting Password Protect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Entering the Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Restricting Button Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Setting Control Panel Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Lens Operation Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Anti-Theft Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Installing the wire lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .
    .
    .

    37
    37
    37
    38
    39
    39
    40
    41
    41

    Configuration Menu
    Using the Configuration Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
    List of Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
    Image Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Signal Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Settings Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Extended Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Network Menu (EB-Z8000WU only). . . . . . . . . . . . . . . . . . . . . . . . . .
    Network Menu (EB-Z8050W only). . . . . . . . . . . . . . . . . . . . . . . . . . .
    Notes on operating the network menu. . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    44
    46
    48
    49
    51
    54
    55



  • Page 4

    Contents

    4

    Soft keyboard operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Basic Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Wireless LAN Menu (only when the optional wireless LAN unit is installed). . . .
    Security menu (Only available when the optional wireless LAN unit is installed)
    .... .. ...... ..... ..... .. ...... ..... ...... .. ..... ...... .
    Wired LAN Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Mail Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Others Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Reset Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Info Menu (Display Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Reset Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    . 55
    . 56
    . 57
    .
    .
    .
    .
    .
    .
    .

    59
    63
    64
    65
    66
    67
    68

    Replacing the Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Lamp replacement period. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    How to replace the lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Resetting the Lamp Hours. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Replacing the Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Air filter replacement period. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    How to replace the air filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    89
    89
    89
    91
    92
    92
    92

    Optional Accessories and Consumables. . . . . . . . . . . . . . . . . . . . . . . 94
    Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
    Consumables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

    Notes on Transportation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

    Troubleshooting
    Using the Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
    Problem Solving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
    Reading the Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    t Indicator is lit or flashing red. . . . . . . . . . . . . . . . . . . . . . . . . . .
    m o n Indicator is flashing or lit. . . . . . . . . . . . . . . . . . . . . . . . . .
    When the Indicators Provide No Help. . . . . . . . . . . . . . . . . . . . . . . . .
    Problems relating to images. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Problems when projection starts. . . . . . . . . . . . . . . . . . . . . . . . . .
    Other problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    .
    .
    .
    .
    .
    .
    .

    71
    72
    73
    75
    76
    80
    81

    Moving Nearby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    When Transporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Preparing packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Notes when packing and transporting. . . . . . . . . . . . . . . . . . .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    .
    .
    .
    .

    96
    96
    96
    96

    Saving a User's Logo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
    Making a WPS (Wi-Fi Protected Setup) Connection with a
    Wireless LAN Access Point (EB-Z8050W only). . . . . . . . . . . . . . . . . . 99
    Connection Setup Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
    Making a Connection Using the Push Button Method. . . . . . . . . . . . . . . . . . . . 99
    Making a connection using the PIN Code Method. . . . . . . . . . . . . . . . . . . . . 101

    Screen Size and Projection Distance. . . . . . . . . . . . . . . . . . . . . . . . . 103

    Appendix

    Projection Distance of EB-Z8000WU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
    Projection Distance of EB-Z8050W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

    Installation Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

    Connecting a LAN Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

    Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

    Connecting to an external monitor. . . . . . . . . . . . . . . . . . . . . . . . . . 106

    Cleaning the Projector's Surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
    Cleaning the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
    Cleaning the Air filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

    Removing and Attaching the Projector Lens Unit. . . . . . . . . . . . . 107

    Replacing Consumables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
    Replacing the Remote Control Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

    Removing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
    Attaching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108



  • Page 5

    Contents

    5

    Reading Problem Mail Notification Function. . . . . . . . . . . . . . . . . 110
    ESC/VP21 Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
    Command List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Cable Layouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Serial Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Communications protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    111
    111
    111
    112

    About PJLink. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
    Supported Monitor Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
    Supported Monitor Displays for EB-Z8000WU. . . . . . . . . . . . . . . . . . . . . . . . . .
    Computer signals (analog RGB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Component Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Composite Video/S-Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Input signal from the HDMI/DVI-D input port. . . . . . . . . . . . . . . . . . . . . . . . .
    Supported Monitor Displays for EB-Z8050W. . . . . . . . . . . . . . . . . . . . . . . . . . .
    Computer signals (analog RGB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Component Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Composite Video/S-Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
    Input signal from the HDMI/DVI-D input port. . . . . . . . . . . . . . . . . . . . . . . . .

    114
    114
    115
    115
    116
    117
    117
    118
    118
    119

    Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
    Projector General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
    Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
    Operating Conditions for the Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

    Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
    Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
    General Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
    Wireless Telegraphy Act Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
    General Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

    Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128



  • Page 6

    Introduction
    This chapter explains the projector's features and the part names.



  • Page 7

    Projector Features
    Ease of use when installed on a ceiling mount
    Centered lens
    The lens is positioned in the center of the
    projector so it is well balanced and is easy
    to mount on a ceiling. This also makes it
    easy to line up the screen and the projector.

    Equipped with electric lens shift, zoom and focus functions
    Using the lens shift function that allows you to adjust the position of the projected image along the horizontal and vertical axis opens up a wide variety of installation locations.
    The lens shift, zoom, and focus functions can be operated with a remote control so operation is easy even if the projector is mounted on the ceiling.

    Six optional lenses are provided
    You can select the best lens according to
    the projection distance and purpose. All
    the optional lenses are bayonet-type
    which allows you to simply and easily
    replace and install the optional lenses.
    s p.94, p.107

    7

    Horizontal and vertical installation possible
    The projector can be pointed either up or
    down to project images on the ceiling or
    floor. This makes it an effective
    communication tool that lets you express
    your ideas with great impact. s p.84

    A design that harmonizes with the surrounding environment, and
    makes the installation easy
    The projector's sophisticated design has a
    cable cover in which cables are hidden for
    a clean exterior appearance.
    The bar type handles are designed to
    make moving and installing the projector
    easy so it can be handled safely. The
    ceiling mount is attached to these handles
    to mount the projector on the ceiling.
    The projector does not need to be turned
    upside down so installation is easy. The
    initial settings can be easily set as you
    look at the screen because the control
    panel is arranged on the back of the
    projector.

    Easy maintenance
    You can replace the lamp by opening a cover and pulling it straight out of the back of
    the projector without using a screwdriver.
    There is only one air filter so cleaning and replacement are easy. The lamp and air filter can be safely replaced even when mounted on the ceiling because their covers do
    not fall off even if you release them.



  • Page 8

    Projector Features

    Reliablity you can depend on
    The projector is equipped with two lamps. Even if one of the lamps
    breaks, you can continue projecting with the other lamp and avoid
    disrupting important presentations.

    8

    Enhanced security functions
    Password Protect to restrict and manage users
    By setting a Password you can restrict who can use the projector. s p.37

    Control Panel Lock restricts button operation on the Control panel.

    Large Projection Area and Precise Colors
    Equipped with a high-resolution WUXGA panel (EB-Z8000WU only)
    You can project a dramatic amount of
    information on the screen. Viewers can
    see the information at a glance without
    having to scroll or switch screens.

    Epson Cinema Filter supports the color gamut for digital cinema.
    Select Theatre or sRGB in Color Mode to use Epson Cinema Filter for 100% reproduction of the color gamut used for digital cinema. As a result, this reproduces colors
    that are full and deep.

    You can use this to prevent people from changing projector settings without permission at events, in schools, and so on. s p.39

    Equipped with various anti-theft devices
    The projector is equipped with the following types of anti-theft security devices.
    s p.41

    • Security slot
    • Security cable installation point

    Easy to handle
    Direct power On/Off
    In places where power is managed centrally, such as in a conference room, the projector can be set to power on and off automatically when the power source to which the
    projector is connected is switched on or off.

    Precise color adjustments
    As well as Color Mode, you can also adjust the image's absolute color temperature
    and the strength of each RGB color. Also, because you can adjust the hue, saturation,
    and brightness of each RGBCMY, the image can be projected with depth and a color
    matching in superior detail.

    No cool down delay
    After turning the projector's power off, you can disconnect the projector's power cable without having to wait for the projector to cool down.

    Using the projector over a network (EB-Z8050W
    only)
    You can make effective use of your network by using the supplied
    "EPSON Projector Software for Meeting & Monitoring" to perform



  • Page 9

    Projector Features

    efficient and varied presentations and meetings. s Projector Operation
    Guide
    Connect to the projector from computers via a network
    You can use your existing network to share the projector from multiple computers.
    Documents can be projected from each computer without having to change any cables during meetings or presentations. Also, you don't have to worry about the distance between the computer and the projector.

    Connecting wirelessly to a computer
    When you install the optional wireless LAN unit in the projector, you can connect wirelessly to a computer.

    9



  • Page 10

    Part Names and Functions

    10

    Name

    Front/Top
    The illustration shows the projector with a standard zoom lens installed.

    Name

    A Handle

    Function
    Use these handles when carrying the projector. Also,
    you can pass an anti-theft wire lock through the handles
    to secure the projector. s p.41

    Caution
    Do not carry the projector by one person.
    Two people are needed to unpack or carry the projector.

    Function

    B Security slot( )

    The Security slot is compatible with the Microsaver
    Security System manufactured by Kensington.
    s p.41

    C Air intake vent
    (Air filter)

    Takes in air to cool the projector internally. If dust
    collects here it can cause the internal temperature to
    rise, and this can lead to problems with operation and
    shorten the optical engine's service life. Be sure to clean
    the Air filter regularly. s p.85, p.92

    D Front adjustable foot

    When set up on a desk, turn to extend and retract to
    adjust the horizontal tilt.
    The front adjustable feet can be removed when the
    projector is installed on a ceiling. s Quick Start Guide

    E Front cover

    Remove this cover to remove or install the lens unit
    when replacing the lens. s p.107
    This cover must be installed when using the projector.

    F Remote Receiver

    Receives signals from the remote control. s Quick
    Start Guide

    G Interface cover

    Remove this cover to connect cables to the ports inside
    when connecting the projector to video equipment.
    s Quick Start Guide , p.11

    H Projection lens

    Images are projected through here.

    I Interface cover open/
    close switch

    Opens and closes the interface cover. s Quick Start
    Guide

    J Ceiling mount fixing
    points
    (Four points)

    Attach the optional Ceiling mount here when
    suspending the projector from a ceiling. s p.84,
    p.94



  • Page 11

    Part Names and Functions

    11

    Name

    Interface

    E Cable holder

    Connection may become defective when a thick heavy
    HDMI cable is connected to the HDMI input port. Run
    a commercially available cable tie through this holder to
    prevent the cable from disconnecting.

    F Computer input port

    For analog RGB signals from a computer and
    component video signals from other video sources.
    s Quick Start Guide

    G Power inlet

    Connects to the power cable. s Quick Start Guide

    H Remote port

    Connects the optional remote control cable set and
    inputs signals from the remote control. When the
    remote control cable is plugged into this port, the
    remote receiver on the projector is disabled.

    I RS-232C port

    When controlling the projector from a computer,
    connect it to the computer with an RS-232C cable. This
    port is for control use and should not normally be used.
    s p.111

    J Wireless LAN Unit
    port (EB-Z8050W only)

    Connects to the optional wireless LAN unit.

    K Monitor Out port

    Outputs to an external monitor the analog signal from
    the computer connected to the Computer input port or
    the BNC input port. This is not available for component
    video signals or other signals being input to any port
    other than the Computer input port or the BNC input
    port. s p.106

    L LAN port
    (EB-Z8000WU only)

    Connects to a LAN cable and then to a network.
    s p.105

    M DVI-D input port

    Inputs digital RGB signals from a computer connected
    to the DVI-D output port. This projector is compatible
    with HDCPg signals. s Quick Start Guide

    N LAN Port
    (EB-Z8050W only)

    Connects to a LAN cable and then to a network.
    s p.105

    The following ports can be accessed by removing the interface cover.
    For information on how to remove the interface cover and connect
    video equipment, s Quick Start Guide .

    Name

    A HDMI input port

    Function
    Inputs video signals from HDMI compatible video
    equipment and computers. This projector is compatible
    with HDCPg signals. s Quick Start Guide

    B BNC input port

    For analog RGB signals from a computer and
    component video signals from other video sources.
    s Quick Start Guide

    C Video input port

    For composite video signals from video sources.
    s Quick Start Guide

    D S-Video input port

    For S-video signals from video sources. s Quick Start
    Guide

    Function



  • Page 12

    Part Names and Functions

    12

    Name

    Rear

    Name

    A Air exhaust vent
    (Lamp cover)

    Function
    Exhaust vent for air used to cool the projector internally.
    Also, open this cover to replace the projector's lamps.

    Function

    E Status indicators

    The color of the indicators and whether they are flashing
    or lit indicate the status of the projector. The left
    illustration indicates EB-Z8050W. EB-Z8000WU has no
    Wireless indicator. s p.71

    F [</ ][>/ ] button

    Corrects horizontal Keystone distortion. If pressed while
    the configuration menu or a Help screen is displayed,
    these buttons only have the [ ] and [ ] functions
    which select menu items and setting values. s Quick
    Start Guide , p.43

    G [Shutter] button

    Press this button to open or close the electric shutter.
    You can close the electric shutter to completely block a
    projection. s Quick Start Guide , p.24

    H [Esc] button

    Stops the current function.
    If pressed when the configuration menu is displayed, it
    moves to the previous menu level. s p.43

    I [w/ ][v/
    button

    ]

    Caution
    Do not place objects that may become warped or
    otherwise affected by heat near the Air exhaust
    vent and do not put your face or hands near the
    vent while projection is in progress.

    B Rear foot

    When set up on a desk, turn to extend and retract to
    adjust the horizontal tilt.
    The rear adjustable feet can be removed when the
    projector is installed on a ceiling. s Quick Start Guide

    C Lamp cover open tab

    Use these tabs to open the lamp cover. s p.89

    D Remote Receiver

    Receives signals from the remote control. s Quick
    Start Guide

    Corrects vertical Keystone distortion. If pressed while
    the configuration menu or a Help screen is displayed,
    these buttons only have the [ ] and [ ] functions
    which select menu items and setting values. s Quick
    Start Guide , p.43

    J [Enter] button

    If pressed during projection of computer analog RGB
    signals, it automatically adjusts the Tracking, Sync., and
    Position to project the optimum image.
    When the configuration menu or a Help screen is
    displayed, it accepts and enters the current selection and
    moves to the next level. s p.43

    K [Menu] button

    Displays and closes the configuration menu.
    s p.43

    L [Source Search]
    button

    Changes to the next input source that is connected to
    the projector and is sending an image. s p.21

    M [Lens] button

    Press this button to cycle through the focus, zoom, and
    lens shift settings to adjust the lens. s Quick Start Guide



  • Page 13

    Part Names and Functions

    Name

    N [t] button

    13

    Function
    Turns the projector power On or Off. s Quick Start
    Guide

    Remote Control



  • Page 14

    Part Names and Functions

    Name

    14

    Function

    A [t] button

    Turns the projector power On or Off. s Quick Start
    Guide

    B [Computer] button

    Changes to images from the Computer input port.
    s p.22

    C [BNC] button

    Changes to images from the BNC input port. s p.22

    D [Video] button

    Changes to images from the Video input port. s p.22

    E [S-Video] button

    Changes to images from the S-Video input port.
    s p.22

    F [Menu] button

    Displays and closes the configuration menu. s p.43

    G [h] button

    When the configuration menu or Help screen is
    displayed, it selects menu items and setting values.
    s p.43, p.70
    When using the optional wireless mouse receiver, tilting
    this button moves the pointer in the direction (eight
    possible directions) tilted.

    H [Enter] button

    When the configuration menu or a Help screen is
    displayed, it accepts and enters the current selection and
    moves to the next level. s p.43, p.70
    Acts as a mouse's left button when using the optional
    wireless mouse receiver.

    I [Page] buttons
    [[][]]

    When using the optional wireless mouse receiver, you
    can change the PowerPoint file page during projection
    by pressing the page up/page down buttons.

    J [Shutter] button

    Each time you press this button, the electric shutter
    closes or opens.
    You can close the electric shutter to completely block a
    projection. s Quick Start Guide , p.24

    K [Auto] button

    If pressed during projection of computer analog RGB
    signals, it automatically adjusts the Tracking, Sync., and
    Position to project the optimum image.

    L [Aspect] button

    The Aspect Ratiog changes each time the button is
    pressed. s p.25

    Name

    Function

    M [Lens Shift] button

    Press to adjust the lens shift. s Quick Start Guide

    N [ID] button

    Press to set the remote control ID. s p.34

    O [Help] button

    Displays and closes the Help screen which shows you
    how to deal with problems if they occur. s p.70

    P Remote port

    Connects the optional remote control cable set and
    outputs signals from the remote control. When the
    remote control cable is plugged into this remote port,
    the remote receiver is disabled.

    Q [Zoom] button

    Press to adjust the zoom. s Quick Start Guide

    R [Num] button

    Use this button to enter passwords, IP Address from the
    Network, and so on. s p.37

    S [Focus] button

    Press to adjust the focus. s Quick Start Guide

    T Numeric buttons

    Use this button to enter passwords, remote control IP
    settings, IP Address from the Network, and so on.
    s p.34, p.37

    U [Color Mode] button

    Each time the button is pressed, the Color Mode changes.
    s p.23

    V [Freeze] button

    Images are paused or unpaused. s p.24

    W [E-Zoom] buttons
    [z][x]

    The [z] button enlarges the image without changing the
    projection size.
    The [x] button reduces the parts of images that have
    been enlarged using the [z] button. sp.31

    X [Pointer] button

    Press to activate the on screen pointer. s p.30

    Y [ESC] button

    Stops the current function. If pressed when the
    configuration menu is displayed, it moves to the
    previous menu level. s p.43, p.70
    Acts as a mouse's right button when using the optional
    wireless mouse receiver.



  • Page 15

    Part Names and Functions

    Name

    15

    Function

    Z [User] button

    Press to assign a frequently used item from the six
    available configuration menu items. By pressing the
    button the assigned menu item selection/adjustment
    screen is displayed, allowing you to make one-touch
    settings/adjustments. s p.48
    Test Pattern is assigned as the default setting.

    a [LAN] button

    Changes to images of EasyMP Network Projection.
    (EB-Z8050W only) s p.22
    This button does not function when using EB-Z8000WU.

    b ID switch

    Use this switch to enable (On)/disable (Off) ID settings
    for the remote control. s p.32

    c [DVI-D/HDMI] button

    Each time the button is pressed, the image displayed
    changes between the DVI-D and HDMI input ports.
    s p.22

    d [Search] button

    Changes to the next input source that is connected to
    the projector and is sending an image. s p.21

    e Indicators

    A light is emitted when outputting remote control signals.

    f Remote control
    light-emitting area

    Outputs remote control signals.



  • Page 16

    Useful Functions
    This chapter explains useful tips for giving presentations, and the Security functions.



  • Page 17

    Correcting Distortion in the Projected Image
    There are two methods of correcting distortion in projected images as
    below.
    • Quick Corner
    This allows you to manually correct each of the four corners of the
    projected image separately. s p.18
    We recommend using Quick Corner to accurately adjust keystone
    distortion.
    • H/V-Keystone
    This allows you to manually correct distortion in the horizontal and
    vertical directions independently. You can perform easy H/V-Keystone
    corrections by using the [w/ ] [v/ ] [</ ] and [>/ ] buttons
    on the projector's control panel. s Quick Start Guide

    q

    Shift the lens to the position shown below when performing
    horizontal and vertical keystone. When the lens shift is not
    positioned as below, the distortion is not corrected accurately.
    • The horizontal lens shift is set to the center.
    • The vertical lens shift is set to the top or bottom.
    The correction may not be properly performed according to the
    zoom adjustment value. And, the projected screen size may become
    smaller after performing the correction. Be careful about the
    projection distance when installing the projector.

    Quick Corner and horizontal and vertical keystone cannot be performed
    at the same time. When the Keystone correction method is selected
    from the configuration menu, the correction method you choose is
    assigned to the [w/ ], [v/ ], [</ ], and [>/ ] buttons on the
    control panel. The default setting for Keystone is set to H/V-Keystone,
    so when [w/ ], [v/ ], [</ ], and [>/ ] buttons are pressed, H/
    V-Keystone correction is carried out.

    17

    Because Quick Corner and H/V-Keystone correction can be carried out
    while projecting a test pattern, you do not need to make preparations
    by connecting a computer or other equipment.



  • Page 18

    Correcting Distortion in the Projected Image

    18

    Correcting Distortion with Quick Corner
    Procedure

    A Press the [Menu] button, and then from the configuration
    menu select Settings - Keystone. s "Using the
    Configuration Menu"
    Using the Remote Control

    Using the Control panel

    C Use the [h] button on the remote control or the [w/

    ], [v/
    ], [</ ], and [>/ ] buttons on the control panel to select
    the corner you want to adjust, and then press the [Enter]
    button.

    B Select "Quick Corner", and then press the [Enter] button.
    Press the [Enter] button again to display the selection screen from
    which you can select one of the four corners.



  • Page 19

    Correcting Distortion in the Projected Image

    D To adjust the shape, use the [h] button on the remote
    control or the [w/
    the control panel.

    ], [v/

    ], [</ ], and [>/ ] buttons on

    19

    E Repeat procedures 3 and 4 as needed to adjust any
    remaining corners.

    F When you are done, press the [Esc] button to exit the
    correction menu.

    Because the correction method was changed to Quick Corner
    from Keystone in the configuration menu, when [w/ ], [v/ ],
    [</ ], and [>/ ] buttons are pressed later, the screen for
    selecting the corner in procedure 2 is displayed. Change Keystone
    from the configuration menu to H/V-Keystone if you want to
    correct H/V-Keystone when pressing the [w/ ], [v/ ], [</ ],
    and [>/ ] buttons on the control panel.

    If the triangle in the direction you are adjusting the shape turns
    gray, as shown in the screenshot below, you cannot adjust the
    shape any further in that direction.



  • Page 20

    Correcting Distortion in the Projected Image

    q

    If the [Esc] button is held down for about two seconds while
    correcting with Quick Corner, the following screen is displayed.

    Reset Quick Corner: Resets the result of Quick Corner corrections.
    Switch to H/V-Keystone: Switches the correction method to H/
    V-Keystone. s p.48

    20



  • Page 21

    Changing the Projected Image
    You can change the projected image in the following two ways.
    • Changing by Source Search
    The projector automatically detects signals being input from connected
    equipment, and the image being input from the equipment is projected.
    • Changing directly to the target image
    You can use the remote control buttons to change to the target input
    port.

    Automatically Detect Input Signal and Change
    the Projected Image (Source Search)

    21

    F HDMI
    G LAN (EB-Z8050W only): The images projected using EasyMP
    Network Projection from a computer connected to the projector
    via a network.
    Skipped when no image signal is being input.

    Procedure
    When your video equipment is connected, start playback before
    beginning this operation.
    Using the Remote Control

    Using the Control panel

    You can project the target image quickly as input ports with no image
    signal being input are ignored when you change by pressing the [Source
    Search] button on the Remote Control or the Control panel.

    When two or more pieces of equipment are connected, press the
    [Source Search] button until the target image is projected.

    A
    B
    C
    D
    E

    Computer
    BNC
    DVI-D
    S-Video
    Video



  • Page 22

    Changing the Projected Image

    q

    The following screen showing the status of image signals is
    displayed when only the image that the projector is currently
    displaying is available, or when no image signal can be found. You
    can select the input port where the equipment you want to use is
    connected. If no operation is performed after about 10 seconds, the
    screen closes.

    22

    Switch to the target image by Remote Control
    You can change directly to the target image by pressing the following
    buttons on the Remote Control.
    Remote Control

    LAN is displayed on the screen only when using EB-Z8050W.

    A
    B
    C
    D

    Changes to images from the Computer input port.
    Changes to images from the Video input port.
    Changes to images from the S-Video input port.

    Changes to images of EasyMP Network Projection. (EB-Z8050W only)
    This button does not function when using EB-Z8000WU.
    E Each time the button is pressed, the image displayed changes between the
    DVI-D and HDMI input ports.
    F Changes to images from the BNC input port.



  • Page 23

    Functions for Enhancing Projection
    Selecting the Projection Quality (Selecting Color
    Mode)

    23

    Procedure
    Remote Control

    You can easily obtain the optimum image quality simply by selecting
    the setting that best corresponds to your surroundings when projecting.
    The brightness of the image varies depending on the mode selected.
    Mode

    Application

    Dynamic

    Ideal for use in a bright room. This is the
    brightest mode.

    Presentation

    Ideal for making presentations using color
    materials in a bright room.

    Theatre*

    Ideal for watching films in a dark room. Gives
    images a natural tone almost like an original source.

    Photo

    (When computer images (analog RGB/digital
    RGB) are input)
    Ideal for projecting still pictures, such as photos,
    in a bright room. The images are vivid and
    brought into contrast.

    Sports

    (When Component Video, S-Video, or composite
    video images are input)
    Ideal for watching TV programmes in a bright
    room. The images are vivid and brought to life.

    sRGB*

    Ideal for images that conform to the sRGBg
    color standard.

    Customized

    Select Customized to adjust R,G,B,C,M,Y from
    Color Adjustment in the configuration menu.

    *

    The Epson Cinema Filter deploys automatically when Theatre or sRGB is
    selected.

    The Color Mode name is displayed on the screen by pressing the button.
    If you press the button while the Color Mode name is displayed on the
    screen, it changes to the next Color Mode.

    q

    The color mode can also be set using Color Mode in the Image
    menu from the configuration menu. s p.44



  • Page 24

    Functions for Enhancing Projection

    24

    Setting the Auto Iris
    By automatically setting the luminance according to the brightness of
    the displayed image, it lets you enjoy deep and rich images.

    Procedure

    A Press the [Menu] button, and select Image - Auto Iris from

    Procedure

    the configuration menu. s "Using the Configuration Menu"
    Using the Remote Control

    Using the Control panel

    B Select On.

    Using the Remote Control

    Each time you press the buttons, the electric shutter closes or opens.

    The setting is stored for each Color Mode.

    C Press the [Menu] button to close the configuration menu.

    q

    • Auto Iris can be set only when the Color Mode is Dynamic,
    Theatre, or Customized.
    • When Multi-screen is set to On, Auto Iris does not work.

    Hiding the Image Temporarily (Shutter)
    You can use this when you want to focus the audience's attention on
    what you are saying, or if you do not want to show details such as
    when you are changing between files during presentations from a computer.

    Using the Control panel

    q

    • When the shutter is closed and no operations are performed for
    about 120 minutes, the projector enters Sleep Mode and turns
    off automatically. If you do not want Sleep Mode to activate,
    change the Shutter Timer setting to Off from Operation in the
    Extended menu. s p.49
    • If you press [t] button while the shutter is closed, the shutter
    automatically opens and a message requesting confirmation to
    turn off the power is displayed on the screen.

    Freezing the Image (Freeze)
    When the moving image on the screen is frozen, the image continues
    to project, so you can project a moving image one frame at a time like



  • Page 25

    Functions for Enhancing Projection

    a still photo. Also, you can perform operations such as changing
    between files during presentations from a computer without projecting
    any images if the freeze function is activated beforehand.

    Procedure
    Remote Control

    25

    Changing the Aspect Ratio
    Change the Aspect Ratiog when video equipment is connected so that
    images that have been recorded in digital video or onto DVDs can be
    viewed in 16:9 wide-screen format. Change the Aspect Ratio when
    projecting computer images at full size. The changing methods and the
    types of Aspect ratio are as follows.

    Changing methods
    Procedure
    Remote Control

    Each time you press the button, Freeze turns on or off.

    q

    • The image source continues to play back the moving images
    even while Freeze is on, and so it is not possible to resume
    projection from the point where it was paused.
    • If the [Freeze] button is pressed while the configuration menu or
    a Help screen is displayed, the menu or Help screen being
    displayed is cleared.
    • Freeze still works while E-Zoom is being used.

    The Aspect name is displayed on the screen by pressing the button.
    If you press the button while the Aspect name is displayed on the
    screen, it changes to the next Aspect Mode.

    q

    The aspect mode can also be set using Aspect in the Signal menu
    from the configuration menu. s p.46

    Changing the Aspect for video equipment images
    Each time the button is pressed, the aspect changes in the order
    Normal, 16:9, Full, Zoom, and Native.



  • Page 26

    Functions for Enhancing Projection

    A
    B
    C
    D
    E

    Normal
    16:9
    Full
    Zoom
    Native

    26



  • Page 27

    Functions for Enhancing Projection

    27

    Changing the Aspect for computer images
    You can change the aspect of projected images input from the Computer, BNC, DVI-D, or HDMI input port as follows. The original aspect ratio is
    16:10 because of the wide panel mounted on the projector. When projecting onto 16:9 screens, set the Aspect to 16:9.
    Set Values

    Operation

    Normal
    (When the input source is a
    Computer, DVI-D, or BNC)

    Projects to the full projection size
    retaining the Aspect of the input image.

    Auto
    (Only availble when the
    input source is HDMI)

    Projects in an appropriate aspect based
    on information from the signal being
    input.

    16:9

    Projects to the full projection size at an
    Aspect of 16:9.

    Projection example
    When a 1024x768 signal is input

    When a 1024x768 signal is input



  • Page 28

    Functions for Enhancing Projection

    Set Values

    28

    Operation

    Projection example

    Full

    Project at full size.

    When a 1024x768 signal is input

    Zoom

    Projects the input image enlarged to the
    full lateral direction size as the aspect
    ratio remains. Parts that extend beyond
    the projection size are not projected.

    When a 1024x768 signal is input



  • Page 29

    Functions for Enhancing Projection

    Set Values
    Native

    q

    29

    Operation
    Projects at the resolution of the input
    image size to the center of the screen.
    This is ideal for projecting clear images.
    If the image resolution exceeds the
    panel resolution of your projector, the
    edges of the image are not projected.

    Projection example
    When an 800x600 signal is input

    When a 2048x1536 signal is input

    If parts of the image are missing or it cannot project everything, set Wide or Normal in Resolution from the configuration menu depending on the size
    of the computer panel. s p.46



  • Page 30

    Functions for Enhancing Projection

    Pointer Function (Pointer)

    30

    B Move the Pointer icon (
    Remote Control

    This allows you to move a Pointer icon on the projected image, and
    helps you draw attention to the area you are talking about.

    q

    Procedure

    A Display the Pointer.
    Remote Control

    Each time you press the button, the pointer appears or disappears.

    ).

    You can choose from three different kinds of Pointer icon (
    , or
    menu.
    s p.48

    ,

    ) in Settings - Pointer Shape from the configuration



  • Page 31

    Functions for Enhancing Projection

    Enlarging Part of the Image (E-Zoom)

    31

    B Move the

    (

    ) to the area of the image that you want to

    enlarge.

    This is useful when you want to expand images to see them in greater
    detail, such as graphs and tables.

    Remote Control

    C Enlarge.

    Procedure

    Remote Control

    A Start E-Zoom.
    Remote Control

    Each time the button is pressed, the area is expanded. You can
    expand quickly by holding the button down.
    You can reduce the enlarged image by pressing the [x] button.
    Press the [ESC] button to cancel.

    q

    • The enlargement ratio appears on the screen. The selected area
    can be enlarged to between 1 to 4 times in 25 incremental steps.
    • Tilt the [h] button to scroll through the enlarged image.
    • If E-Zoom is selected, Progressive and Noise Reduction are
    cancelled.
    • E-Zoom is canceled when performing some functions such as
    Keystone or Auto Setup.



  • Page 32

    Limitation of the Number of the Target Projectors when Using Multiple Projectors
    When an ID is set for the projector and the remote control, you can
    use the remote control to operate only the projector with a matching
    ID. This is very useful when managing multiple projectors.

    Operation
    Possible

    Combinations
    Projector ID: 1

    You can set an ID for the projector within a range of "1" to "9". The
    default value is Off.
    You can set an ID for the remote control within a range of "0" to "9".
    The default value is "0". When the ID switch on the side of the remote
    control is set to Off, you can operate all projectors by the remote
    control regardless of the ID setting for the projector or the remote control.
    The following table shows the possible combinations of projector ID
    and remote control ID.
    Operation
    Possible

    Combinations
    Projector ID: 1

    ID switch: On
    Remote control ID: 1
    Possible

    Projector ID: 1

    ID switch: Off
    Remote control ID: 3
    Possible

    Projector ID: Off

    ID switch: On
    Remote control ID: 1

    Descriptions
    When the control switch is
    set to On, and Projector ID
    matches the remote control
    ID, you can operate the
    projector with the remote
    control.
    When the ID switch on the
    side of the remote control is
    set to Off, you can operate
    the projector with the
    remote control regardless of
    the projector's ID setting.
    When the Projector ID is
    Off, you can operate with
    the remote control
    regardless of the remote
    control ID setting.

    ID switch: On
    Remote control ID: 0
    Not possible

    Projector ID: 1

    ID switch: On
    Remote control ID: 3

    32

    Descriptions
    When the remote control ID
    is "0", you can operate with
    the remote control
    regardless of the Projector
    ID setting.

    When the remote control
    switch is On, and Projector
    ID and remote control ID do
    not match, you cannot
    operate with the remote
    control.

    When Remote Control Type is set to Simple from Operation in the
    configuration menu, you cannot set the remote control ID.



  • Page 33

    Limitation of the Number of the Target Projectors when Using Multiple Projectors

    Setting the Projector ID

    Checking the Projector ID
    Use the following procedure to check the projector ID.

    Procedure

    A During projection, press the [Menu] button and select

    Extended - "Projector ID" from the configuration menu.
    s "Using the Configuration Menu"
    Using the Remote Control

    33

    Procedure

    A Set the remote control ID switch to On.

    Using the Control panel

    B During projection, while holding the [ID] button, press the
    [Help] button.

    Remote Control

    B Choose the ID you want to set and press the [Enter] button.
    C Press the [Menu] button to close the configuration menu.

    When you press the buttons, the current Projector ID is displayed
    on the projection screen. It disappears in about three seconds.



  • Page 34

    Limitation of the Number of the Target Projectors when Using Multiple Projectors

    Setting the Remote Control ID
    Procedure

    A Set the remote control ID switch to On.

    B While holding the [ID] button, press a number button to

    select a number to match the ID of the projector you want
    to operate.

    Once this setting has been made, the projector that can be operated by
    the remote control is limited.

    q

    34

    The remote control ID setting is saved in the remote control. Even
    if the remote control batteries are removed to replace them and so
    on, the stored ID setting is retained. However, if the batteries are
    left out for a long time, it is reset to the default value (ID0).



  • Page 35

    Correcting Color for Multiple Projectors (Multi-Screen Color Adjustment)
    When multiple projectors are lined up and projecting images, you can
    manually correct the brightness and color tone of each projector's image
    so that the colors projected from each projector match closely.
    Use the multi-screen color adjustment function when the Color Mode
    of each projector is set to the same item.
    In some cases the brightness and color tone may not match completely
    even after correction.
    Auto Iris does not work while this function is activated. Even if Auto
    Iris is set to On, and Multi-screen is set to On, Auto Iris does not work.

    Summary of Correction Procedure
    When multiple projectors are set up and you need to make corrections,
    use the following procedure to correct one projector at a time.
    1. Set the projector ID and the remote control ID.
    To limit operation to one target projector, set a Projector ID for the target
    projector, and set the same ID for the remote control. s p.32
    2. Correct the color difference.
    You can carry out color correction when projecting from multiple projectors.
    You can adjust from black to white in five stages called levels 1 to 5, and in each
    of these 5 levels you can adjust the following two points.

    • Correcting brightness
    You can correct the image brightness to make them all equal.
    • Correcting color
    You can adjust the image color to make them match more closely by using Color Correct. (G/R) and Color Correct. (B/Y).

    35

    Correction Method
    After setting up the projectors, correct the brightness and tone for each
    projector to reduce the differences.

    Procedure

    A Press the [Menu] button and select Extended - "Multi-screen"
    from the configuration menu. s "Using the Configuration
    Menu"

    B Set "Multi-screen" to "On".
    C Select Lv. to be corrected in Adjustment Level.

    • Each time a level is selected, the pattern of the level selected is
    displayed.
    • You can start correcting from any level, usually you can make
    it darker or lighter by correcting 1 to 5 or 5 to 1.

    D Correct the brightness with Brightness Correct.

    • When you select Lv. 5, all the images are adjusted to the
    darkest image from multiple projectors.
    • When you select Lv. 1, all the images are adjusted to the
    brightest image from multiple projectors.
    • When you select Lv. 2 to 4, all the images are adjusted to the
    mid-range brightness image from multiple projectors.
    • Because each time the [Enter] button is pressed the image
    displayed changes between the pattern display and the actual
    image, you can check the correction results and make
    corrections in the actual image.

    E Correcting Color Correct. (G/R) and Color Correct. (B/Y).
    Because each time the [Enter] button is pressed the image
    displayed changes between the pattern display and the actual



  • Page 36

    Correcting Color for Multiple Projectors (Multi-Screen Color Adjustment)

    image, you can check the correction results and make corrections
    in the actual image.

    F Repeat procedures 3 to 5 until corrections are finished.
    G When all corrections are finished, press the [Menu] button
    to close the configuration menu.

    36



  • Page 37

    Security Functions
    The projector has the following enhanced security functions.
    • Password Protect
    You can limit who can use the projector.
    • Control Panel Lock/Lens Operation Lock
    You can prevent people changing the settings on the projector without
    permission. s p.39
    • Anti-Theft Lock
    The projector is equipped with various types of anti-theft security
    devices. s p.41

    Managing Users (Password Protect)
    When Password Protect is activated, people who do not know the
    Password cannot use the projector to project images even if the
    projector power is on. Furthermore, the user's logo that is displayed
    when you turn on the projector cannot be changed. This acts as an
    anti-theft device as the projector cannot be used even if it is stolen. At
    the time of purchase, Password Protect is not activated.

    Type of Password Protect
    The following three kinds of Password Protect settings can be made
    according to how the projector is being used.
    1. Power On Protect
    When Power On Protect is On, you need to enter a preset Password after the
    projector is plugged in and turned on (this also applies to Direct Power On). If
    the correct Password is not entered, projection does not start.

    37

    2. User's Logo Protect
    Even if someone tries to change the User's Logo set by the owner of the
    projector, it cannot be changed. When User's User's Logo Protect is set to On,
    the following setting changes for the User's Logo are prohibited.

    • Capturing a User's Logo
    • Settings for Display Background, and Startup Screen from Display
    in the configuration menu
    3. Network Protect
    When Network Protect is set to On setting changes for Network Menu in the
    configuration menu are prohibited.

    Setting Password Protect
    Use the following procedure to set Password Protect.

    Procedure

    A During projection, hold down the [Freeze] button for about
    five seconds.
    The Password Protect setting menu is displayed.
    Remote Control



  • Page 38

    Security Functions

    q

    38

    Remote Control

    • If Password Protect is already activated, you must enter the
    Password.
    If the Password is entered correctly, the Password Protect setting
    menu is displayed. s "Entering the Password"
    • When the Password is set, stick the Password protect sticker in a
    visible position on the projector as a further theft deterrent.

    B Turn on Power On Protect.
    (1)
    (2)
    (3)

    Select Power On Protect, and then press the [Enter] button.
    Select On, and then press the [Enter] button.
    Press the [ESC] button.

    C Turn on User's Logo Protect.
    (1)
    (2)
    (3)

    Select User's Logo Protect, and then press the [Enter] button.
    Select On, and then press the [Enter] button.
    Press the [ESC] button.

    D Turn on Network Protect.
    (1)
    (2)
    (3)

    Select Network Protect, and then press the [Enter] button.
    Select On, and then press the [Enter] button.
    Press the [ESC] button.

    E Set the Password.
    (1)
    (2)

    (3)

    Select Password, and then press the [Enter] button.
    The message "Change the password?" is displayed, select Yes and then
    press the [Enter] button. The default setting for the Password is "0000".
    Change this to your own desired Password. If you select No, the screen
    shown in step 1 is displayed again.
    While holding down the [Num] button, enter a four digit number using
    the numeric buttons. The number entered is displayed as "* * * *". When
    you enter the fourth digit, the confirmation screen is displayed.

    (4)

    Re-enter the Password.
    The message "Password accepted." is displayed.
    If you enter the Password incorrectly, a message is displayed prompting
    you to re-enter the password.

    Entering the Password
    When the Password entry screen is displayed, enter the Password using
    the numeric buttons on the Remote Control.

    Procedure
    While holding down the [Num] button, enter the Password by
    pressing the numeric buttons.
    When you enter the correct Password, projection begins.



  • Page 39

    Security Functions

    Attention
    • If an incorrect Password is entered three times in succession, the message
    "The projector's operation will be locked." is displayed for about five
    minutes, and then the projector switches to standby mode. If this happens,
    disconnect the power plug from the electrical outlet and then reinsert it
    and turn the projector's power back on. The projector displays the
    Password entry screen again so that you can enter the correct Password.
    • If you have forgotten the password, make a note of the "Request Code:
    xxxxx" number that appears on the screen and contact the nearest address
    provided in the Support and Service Guide. s Epson Projector Contact
    List
    • If you continue to repeat the above operation and input the wrong
    Password thirty times in succession, the following message is displayed and
    the projector does not accept any more Password entries. "The projector's
    operation will be locked." Contact Epson as described in your
    documentation. s Epson Projector Contact List

    Restricting Button Operation

    39

    Setting Control Panel Lock
    Perform one of the following to lock the operation buttons on the
    Control panel. Even if the control panel is locked, you can still use the
    remote control as usual.
    • Full Lock
    All of the buttons on the Control panel are locked. You cannot
    perform any operations from the Control panel, including turning the
    power on or off.
    • Partial Lock
    All of the buttons on the Control panel, except for the [t] button,
    are locked.

    Procedure

    A During projection, press the [Menu] button and select

    Settings - Control Panel Lock from the configuration menu.
    s "Using the Configuration Menu"
    Using the Remote Control

    The following two kinds of operation restriction functions are available
    with the projector.
    • Control Panel Lock
    This is useful at events or shows when you want to deactivate all
    buttons during projection or at schools when you want to limit
    button operation.
    • Lens Operation Lock
    This function deactivates all buttons on the remote control related to
    the lens operation to prevent improper lens adjustment after it is
    properly adjusted.

    Using the Control panel



  • Page 40

    Security Functions

    40

    Lens Operation Lock
    This function locks the following buttons on the remote control related
    to the lens operation.
    Remote Control

    B Select either Full Lock or Partial Lock according to your
    purpose.

    Procedure

    C Select Yes when the confirmation message is displayed.
    The Control panel buttons are locked according to the setting you
    chose.

    q

    You can release the Control panel lock by one of the following
    two methods.
    • From the Remote Control, select Off in Settings - Control Panel
    Lock from the configuration menu.
    • Press and hold down the [Enter] button on the Control panel
    for about seven seconds, a message is displayed and the lock is
    released.

    A Press the [Menu] button, and select Settings - "Lens

    Operation Lock" from the configuration menu. s "Using the
    Configuration Menu"
    Using the Remote Control

    Using the Control panel



  • Page 41

    Security Functions

    41

    Anti-Theft Lock
    As the projector is often setup on ceiling mounts and left in rooms
    unattended, the projector includes the following security devices to
    prevent someone from taking the projector.

    B Select "On".

    The buttons related to the lens operation are locked according to
    the setting you chose.

    • Security slot
    The Security slot is compatible with the Microsaver Security System
    manufactured by Kensington. You can find details about the
    Microsaver Security System on the Kensington homepage http://
    www.kensington.com/.
    • Handle
    A commercially available theft-prevention wire lock can be passed
    through the handle to secure the projector to a desk or pillar.

    Installing the wire lock
    Pass an anti-theft wire lock through the handle.
    See the documentation supplied with the wire lock for locking instructions.



  • Page 42

    Configuration Menu
    This chapter explains how to use the configuration menu and its functions.



  • Page 43

    Using the Configuration Menu

    Selecting from the top menu

    43

    Selecting from the sub menu

    Changing the selected item

    Exit



  • Page 44

    List of Functions

    44

    Image Menu
    Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for
    each image signal.
    Analog/Digital Component Videog/
    Composite video g/S-Videog

    Analog RGB/Digital RGB

    Sub Menu

    Function

    Color Mode

    You can select the quality of the image to suit your surroundings. s p.23

    Brightness

    You can adjust the image Brightness.

    Contrast g

    You can adjust the difference between light and shade in the images.

    Color Saturation

    You can adjust the Color Saturation for the images.

    Tint

    (Setting is only possible when NTSC signals are being input if you use composite video/S-Video.)
    You can adjust the image Tint.

    Sharpness

    You can adjust the image sharpness.

    Abs. Color Temp.

    (This item cannot be selected if sRGBg is selected as the Color Mode setting from the Image menu.)
    You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. When a high value is selected the image
    becomes tinged with blue, when a low value is selected the image becomes tinged with red.



  • Page 45

    List of Functions

    Sub Menu

    45

    Function

    Color Adjustment

    (This item cannot be selected if sRGBg is selected as the Color Mode setting from the Image menu.)
    You can make adjustments by choosing one of the following.
    Red, Green, Blue: You can adjust the saturation of each color individually.
    (This item cannot be displayed if Customized is selected as the Color Mode setting from the Image Menu.)
    R, G, B, C, M, Y: You can adjust the hue, saturation, and brightness of each color R (red), G (green), B (blue), C (cyan), M (magenta), Y (yellow)
    individually.
    (This item is displayed only when Customized is selected as the Color Mode setting from the Image Menu.)

    Auto Iris

    (This setting is only possible when the Color Mode setting in the Image Menu is set to Dynamic, Theatre, or Customized, and Multi-screen is set
    to Off.)
    Set whether or not (On/Off) to adjust to the optimum light status for images being projected. s p.24
    The setting is stored for each Color Mode.

    Reset

    You can reset all adjustment values for the Image menu functions to their default settings. To return all menu items to their default settings, see
    s p.68



  • Page 46

    List of Functions

    46

    Signal Menu
    Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for
    each image signal.
    Analog RGB

    Sub Menu

    Digital RGB/
    Digital Component Video g

    Analog Component Video

    Composite videog/S-Videog

    Function

    Auto Setup

    You can select whether or not (On/Off) Auto Setup automatically adjusts the image to the optimum state when the Input Signal changes.
    s p.78
    Auto Setup is not available when Resolution is set to Customized 1 or Customized 2.

    Resolution

    Auto: The resolution of the input signal is automatically identified.
    Wide, Normal: If the images cannot be projected correctly when Auto is set, set this menu. Set to Wide depending on the connected computer for
    wide screens, or set to Normal for 4:3 or 5:4 screens.
    Manual: You can specify the resolution. This is ideal when connected computer is fixed.

    Tracking g

    You can adjust computer images when vertical stripes appear in the images. s p.78

    Sync. g

    You can adjust computer images when flickering, fuzziness, or interference appear in the images. s p.78

    Position

    You can adjust the display Position up, down, left, and right when a part of the image is missing so that the whole image is projected.

    Progressive

    (Component Video can only be adjusted when 480i/576i/1080i signals are being input. This cannot be set when a digital RGB signal is input.)
    Off: IP conversion is carried out for each field in the screen. This is ideal for viewing images with a large amount of movement.
    Video: This is ideal for viewing general video images.
    Film/Auto: By automatically converting movie films, CG, animated images, and so on recorded in 24/30 frames to the optimum progressive signal
    via 2-3 pull-down, it is possible to recreate the natural feel of the original image.



  • Page 47

    List of Functions

    47

    Sub Menu

    Function

    Noise Reduction

    (This cannot be set when a digital RGB signal is input)
    Smoothes out rough images. There are two modes. Select your favorite setting. It is recommended that this is set to Off when viewing image
    sources in which noise is very low, such as for DVDs.

    DVI/HDMI Video Range

    (This cannot be set when a digital RGB signal is input)
    When the projector's DVI-D input port or HDMI input port is connected to a DVD player, the projector's video range is set according to the DVD
    player's video range setting.

    Input Signal

    You can select an input signal from Computer input port or BNC input port.
    If Auto is set, the input signal is identified automatically according to the connected equipment.
    If colors do not appear correctly when this is set to Auto, select the appropriate signal according to the connected equipment.

    Video Signal

    You can select input signal from Video input port. If set to Auto, video signals are recognized automatically. If interference appears in the image or
    a problem occurs such as no image is being projected when set to Auto, select the appropriate signal according to the connected equipment.

    Aspect

    You can set the Aspect Ratiog for projected images. s p.25

    Overscan

    (This cannot be set when a digital RGB signal is input)
    You can change the Output Scaling (the range of projected image). The range of trimming screen can be set to Off, 4%, or 8%. You can select Auto
    only when the input source is HDMI. When Auto is selected, the range is automatically switched to Off or 8% according to the input signal.
    However, the automatic setting is only effective when the video equipment is connected via the projector's HDMI port.

    Reset

    You can reset all adjustment values on the Signal menu to their default settings, except for Input Signal.
    To return all menu items to their default settings, see s p.68



  • Page 48

    List of Functions

    48

    Settings Menu

    Sub Menu
    Keystone

    Function
    You can correct keystone distortion.
    H/V-Keystone: Corrects horizontal and vertical keystone distortion. Select one of V-Keystone or H-Keystone.
    Use the [w/

    ], [v/

    ], [</

    ], and [>/

    ] buttons on the control panel to perform similar corrections to V-Keystone and H-Keystone.

    Quick Corner: Selects and corrects the four corners of the projected image. s p.18
    Control Panel Lock

    You can use this to restrict operation of the projector's Control panel. s p.39

    Lens Operation Lock

    You can use this to restrict the lens operation of the remote control. s p.40

    Pointer Shape

    You can select the shape of the pointer. s p.30
    Pointer 1:

    Pointer 2:

    Pointer 3:

    Power Consumption

    You can set the lamp brightness to Normal or ECO.
    Select ECO if the images being projected are too bright such as when projecting images in a dark room or onto a small screen. When ECO is
    selected, the amount of electricity consumed and the lamp's operating life are changed as follows, and the fan rotation noise during projection is
    reduced. Electrical consumption: about 16% decrease, lamp life: about 1.4 times longer

    Remote Receiver

    You can limit the reception of the operation signal from the Remote Control.
    When you want to prohibit operation by Remote Control, or if the Remote Receiver has a fluorescent light too close to it, you can make settings to
    deactivate the remote receiver you do not want to use or that is experiencing interference.

    User Button

    You can select the item assigned from the configuration menu with the Remote Control's [User] button. By pressing the [User] button the assigned
    menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/adjustments. You can assign one of the following six
    items to the [User] button.
    Power Consumption, Info, Progressive, Test Pattern, Multi-screen, and Resolution



  • Page 49

    List of Functions

    Sub Menu

    49

    Function

    Test Pattern

    When the projector is setup, a Test Pattern is displayed so that you can adjust the projection without connecting other equipment. While the Test
    Pattern is displayed, zoom, focus adjustments, and Keystone correction can be performed.
    To cancel the Test Pattern, press the [ESC] button on the Remote Control or the Control panel.

    Reset

    You can reset all adjustment values on the Settings menu to their default settings, except for User Button.
    To return all menu items to their default settings, see s p.68

    Extended Menu

    Sub Menu

    Function

    Display

    You can make settings related to the projector's display.
    Messages: The following messages are not displayed on the screen when this item is set to Off.
    Overheating and other warnings, messages such as when there is no video input, and when Freeze is On or when changing Source,
    Color Mode or Aspect.
    Display Background*1: You can set the screen status for when no image signal is available to Black, Blue, or Logo.
    Startup Screen*1: You can set whether or not (On/Off) the Startup Screen (the registered User's Logo displays when starting the
    projector) is displayed.
    Menu Size (EB-Z8000WU only): You can select Normal or Larger for the display size of the configuration menu, Help, and other
    messages.

    User's Logo *1

    You can change the User's Logo that is displayed as a background during Display Background or Startup Screen. s p.97

    Projection

    You can set from the following according to the way the projector is set up. s p.84
    Front, Front/Ceiling, Rear, Rear/Ceiling



  • Page 50

    List of Functions

    Sub Menu

    50

    Function

    Direction

    You can set from the following according to the way the projector is set up. s p.84
    Normal, Pointing Up, Pointing Down

    Operation

    Direct Power On: You can set whether or not (On/Off) to enable Direct Power On.
    Be careful when this item is set to On because this unit turns on at the time of power recovery with this unit plugged-in to an outlet.
    Sleep Mode: When set to On, this automatically stops projection when no image signal is being input and no operations are carried
    out.
    Sleep Mode Timer: When Sleep Mode is set to On, you can set the time before the projector automatically turns off within a range
    of 1 to 30 minutes.
    Shutter Timer: When set to On, this turns off the power automatically 120 minutes after the electric shutter is closed. Shutter
    Timer is set to On at the time of purchase. (When Shutter Timer and Sleep Mode are set to On at the same time, Sleep Mode has
    priority.)
    High Altitude Mode: Set to On when using the projector above an altitude of 1500 m.
    BNC Sync Termination: Set the termination for the signal from the BNC input port. This should usually be set to Off. Set to On
    when analog (75Ω) termination such as for switchers is necessary.
    Remote Control Type: You can select Normal or Simple depending on the type of remote control.
    Set this item to Normal to use the remote control provided with the projector. When Simple is selected, you can use the remote
    control provided with other Epson projectors to operate this projector (except for EB-G5350/G5200W/G5100). This is useful if you
    want to use a remote control that you are already familiar with to operate the projector.
    However, you cannot use the remote control provided with the projector if this is set to Simple. Make sure you want to change this
    setting to Simple because, if the projector is mounted on the ceiling or somewhere hard to reach, changing it back may be difficult.

    Standby Mode

    You can use the functions that monitor and control the status of the projector over the network even when the projector is in
    standby mode if this is set to Communication On.
    You can use SNMPg to monitor and control the status of the projector over the network, or by using the EasyMP Monitor software
    supplied with this product.

    Air Filter Notice

    You can set whether or not (On/Off) to enable Air Filter Notice. When this is set to On and a clog in the air filter is detected, the
    message is displayed on the screen.

    Projector ID

    Set the ID within a range of 1 to 9. Off indicates that no ID is set. s p.33

    Multi-screen

    When this is set to On, you can adjust the hue and brightness of images projected from a row of the several projectors. s p.35
    Adjustment Level: You can adjust from black to white in five stages called Level 1 to 5, and in each of these 5 levels you can
    adjust Brightness Correct. and Color Correct.
    Brightness Correct.: Corrects the difference in the brightness of each projector.
    Color Correct. (G/R) / Color Correct. (B/Y): You can correct the difference in the color of each projector.
    When Multi-screen is set to On, Auto Iris does not work.



  • Page 51

    List of Functions

    51

    Sub Menu

    Function

    Language

    You can set the Language for message displays.

    Reset

    You can reset Display*1, Operation*2, and Air Filter Notice from the Extended menu to their default settings.
    To return all menu items to their default settings, see s p.68

    *1 When User's Logo Protect is set to On in Password Protect, settings relating to User's Logo cannot be changed. You can make changes after setting User's Logo
    Protect to Off.s p.37
    *2 Except for High Altitude Mode and Remote Control Type.

    Network Menu (EB-Z8000WU only)
    When Network Protect is set to On in Password Protect, a message is displayed and the settings cannot be changed. You can make changes after
    setting Network Protect to Off. s p.37



  • Page 52

    List of Functions

    Sub Menu

    52

    Function

    Wired LAN

    You can make network settings.
    DHCP: You can set whether or not (On/Off) to use DHCP.
    If this is set to On you cannot set any more addresses.
    IP Address: You can input the IP address assigned to the projector.*
    You can enter a number from 0 to 255 in each field of the address. However, the following IP Addresses cannot be used.
    0.0.0.0, 0.x.x.x, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
    Subnet Mask: You can input the subnet mask for the projector.*
    You can enter a number from 0 to 255 in each field of the address. However, the following Subnet Masks cannot be used.
    0.0.0.0, 255.255.255.255
    Gateway Address: You can input the IP address for the gateway for the projector.*
    You can enter a number from 0 to 255 in each field of the address. However, the following Gateway Addresses cannot be used.
    0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
    MAC Address: You can display the MAC address for the projector.

    PJLink Password

    Set a Password to use when you access the projector using compatible PJLink software.* s p.113
    You can enter up to 32 single-byte alphanumeric characters.

    Web Control Password

    Set a password to use when making settings and controlling the projector using Web Control.* You can enter up to 8 single-byte
    alphanumeric characters.
    Web control is a computer function that allows you to set up and control the projector by using a web browser on the computer
    running EasyMP Monitor. s EasyMP Monitor Operation Guide

    SNMP

    You can make SNMPg settings.
    Trap IP Address 1/Trap IP Address 2: You can register up to two addresses as the SNMP trap notification destination.*
    To use SNMP to monitor the projector, you need to install the SNMP manager program on your computer. SNMP should be
    managed by a network expert.



  • Page 53

    List of Functions

    53

    Sub Menu

    Function

    Mail

    When this is set, you receive an e-mail notification if a problem or warning occurs in the projector. For information on the contents
    of the sent email, s "Reading Problem Mail Notification Function" p.110
    Mail Notification: You can set whether or not (On/Off) to be notified by e-mail. If this is set to Off you cannot set any more
    addresses.
    SMTP Server: You can input the IP address for the SMTP server for the projector.*
    You can enter a number from 0 to 255 in each field of the address. However, the following IP Addresses cannot be used.
    127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
    Port Number: You can display the SMTP server's port number.
    The default value is 25. When editing settings from Web Control, you can change Port Number by entering a valid number from 1
    to 65535.
    Address 1 Setting/Address 2 Setting/Address 3 Setting: You can enter the e-mail address* and the contents of the message to
    receive notification when a problem or warning occurs. You can register up to three destinations. You can enter up to 64 single-byte
    alphanumeric characters for the e-mail addresses.

    AMX Device Discovery

    When the projector is connected to a network, set this to On to allow the projector to be detected by AMX Device Discoveryg. Set
    this to Off if the projector is not connected to an environment controlled with a controller from AMX or AMX Device Discovery.

    Projector Name

    Displays the projector name used to identify the projector when connected to a network.

    Reset

    You can reset all adjustment values for the Network menu to their default settings.
    To return all menu items to their default settings, see s p.68

    *

    When inputting numbers and passwords, the following software keyboards are displayed. Tilt the [h] button on the remote control to move the cursor to the
    target key, and then press the [Enter] button. Enter figures by holding down the [Num] button on the Remote Control, and pressing the numeric buttons. After
    inputting, press [Finish] on the keyboard to confirm your input. Press [Cancel] on the keyboard to cancel your input.

    Each time the [CAPS] key is selected, it sets and changes between upper case and
    lower case letters. Each time the [SYM1/2] key is selected, it sets and changes the
    symbol keys for the section enclosed by the frame.



  • Page 54

    List of Functions

    54

    Network Menu (EB-Z8050W only)
    When Network Protect is set to On in Password Protect, a message is displayed and the settings cannot be changed. You can make changes after
    setting Network Protect to Off. s p.37

    Sub Menu
    Network Configuration

    q

    Function
    The following menus are available for setting network items.
    Basic, Wireless LAN, Security, Wired LAN, Mail, Others, Reset and Setup complete.

    By using the Web browser of a computer connected to the projector on a network, you can set the projector's functions and control the projector. This
    function is called "Web control". You can easily enter text using a keyboard to make settings for Web control such as security settings. s Projector
    Operation Guide "Changing Settings Using a Web Browser (Web Control)"



  • Page 55

    List of Functions

    55

    Notes on operating the network menu
    Selecting from the top menu and sub menus, and changing of selected items are the same as operations in the configuration menu.
    When done, make sure you go to the Setup complete, and select one of Yes, No, or Cancel. When you select Yes or No, you return to the
    configuration menu.

    Yes:
    No:
    Cancel:

    Saves the settings and exits the Network menu.
    Exits to the Network menu without saving the settings.
    Continues displaying the Network menu.

    Soft keyboard operations
    The Network menu contains items that require input of alphanumerics during setup. In this case, the following software keyboard is displayed. Use the
    [h] button on the remote control or [w/ ], [v/ ], [</ ], and [>/ ] on the projector to move the cursor to the desired key, and then press the
    [Enter] button to enter the alphanumeric. Enter figures by holding down the [Num] button on the remote control, and pressing the numeric buttons.
    After inputting, press [Finish] on the keyboard to confirm your input. Press [Cancel] on the keyboard to cancel your input.



  • Page 56

    List of Functions

    56

    A Each time this key is selected, it sets and changes between upper case and lower case letters.
    B Each time this key is selected, it sets and changes the symbol keys for the section enclosed by the frame.

    Basic Menu

    Sub Menu

    Function

    Projector Name

    Displays the projector name used to identify the projector when connected to a network.
    When editing, you can enter up to 16 single-byte alphanumeric characters.

    PJLink Password

    Set a password to use when you access the projector using compatible PJLink software. s p.113
    You can enter up to 32 single-byte alphanumeric characters.



  • Page 57

    List of Functions

    57

    Sub Menu

    Function

    Web Control Password

    Set a password to use when making settings and controlling the projector using Web Control. You can enter up to 8 single-byte alphanumeric
    characters. Web control is a computer function that allows you to set up and control the projector by using the Web browser on a computer
    connected on a network. s Projector Operation Guide "Changing Settings Using a Web Browser (Web Control)"

    Projector keyword

    When set to On, you have to enter the keyword when you try to connect the projector to a computer on a network. As a result, you can prevent
    presentations from being interrupted by unscheduled connections from the computer.
    Normally this should be set to On. s Projector Operation Guide "Connecting to a Projector on a Network and Projecting"

    Wireless LAN Menu (only when the optional wireless LAN unit is installed)

    Sub Menu

    Function

    Wireless LAN Power

    Set to Off to deactivate the wireless LAN unit connected to the projector. When set to Off, the wireless LAN unit is treated as if it were not connected.

    Connection mode

    When the projector is connected to a computer with EasyMP Network Projection, set so that it is in a permanently connected mode.

    Wi-Fi Protected Setup

    When using a WPS (Wi-Fi Protected Setup) compatible access point via a wireless LAN, you can easily connect the projector to the access point
    and make security settings. s p.99

    Antenna level

    Displays the wireless LAN wave strength.

    Wireless LAN system

    Sets the wireless LAN system.

    SSID

    Enter an SSID. When an SSID is provided for the wireless LAN system in which the projector participates, enter the SSID.
    You can enter up to 32 single-byte alphanumeric characters.



  • Page 58

    List of Functions

    58

    Sub Menu

    Function

    DHCP

    You can set whether or not (On/Off) to use DHCPg.
    If this is set to On you cannot set any more addresses.

    IP Address

    You can input the IP addressg assigned to the projector.
    You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used. 0.0.0.0, 127.x.x.x, 224.0.0.0
    to 255.255.255.255 (where x is a number from 0 to 255)

    Subnet Mask

    You can input the Subnet Maskg for the projector. You can input a number from 0 to 255 in each field of the address. However, the following
    subnet masks cannot be used.
    0.0.0.0, 255.255.255.255

    Gateway Address

    You can input the IP address for the gateway for the projector.
    You can input a number from 0 to 255 in each field of the address. However, the following Gateway addressesg cannot be used.
    0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)

    MAC Address

    Displays the MAC address.

    SSID Display

    To prevent the SSID from being displayed on the LAN Standby screen, set this to Off.

    IP Address Display

    To prevent the IP address from being displayed on the LAN Standby screen, set this to Off.



  • Page 59

    List of Functions

    59

    Security menu (Only available when the optional wireless LAN unit is installed)
    When the optional wireless LAN unit is installed and being used in Manual Mode, it is strongly recommended that you set security.

    Sub Menu

    Function
    Select one of the following security methods.
    When setting up security, follow the instructions from the administrator of the network system you are about to access.
    WEP: Data is encrypted with a code key (WEP key)
    This mechanism prevents communication unless the encrypted keys for the access point and the projector match.
    WPA/WPA2: This is an encryption standard that improves security which is a weak point of WEP. Although there are multiple kinds of WPA
    encryption methods, this projector uses "TKIP" and "AES".
    WPA also includes user authentication functions. WPA authentication provides two methods: using an authentication server, or authenticating
    between a computer and an access point without a server. This projector supports the latter method, without a server.
    EAP: EAP is a protocol used for communication between clients and authentication severs. These are multiple protocols, such as EAP-TLS which
    uses electronic certification for user authentication, LEAP which uses user name and password, and EAP-TTLS.

    Security

    Type of security
    System

    Authentication

    EAP-TLS

    Digital certificate, CA certificate

    EAP-TTLS/MD5

    User name, Password

    EAP-TTLS/MS-CHAPv2

    User name, Password

    PEAP/MS-CHAPv2

    User name, Password



  • Page 60

    List of Functions

    60

    System

    Authentication

    PEAP/EAP-GTC

    User name, Password

    LEAP

    User name, Password

    EAP-Fast/MS-CHAPv2

    User name, Password

    EAP-Fast/GTC

    User name, Password

    q

    • If using EAP, you need to make settings at the projector that match the authentication server settings. Check with your network administrator for details
    on RADIUS settings.
    • Open “Network Menu” – “Certificate” in “Web Control” to register a digital certificate and a CA certificate to the projector. Only one set of a digital
    certificate and a CA certificate can be registered to the projector. These certificates are used with EAP-TLS.

    When WEP is selected

    The following items can be set.
    Sub Menu
    WEP encryption

    Function
    You can set the encryption for WEP encoding.
    128 Bit: Uses 128 (104) bit encoding
    64 Bit: Uses 64 (40) bit encoding



  • Page 61

    List of Functions

    61

    Sub Menu

    Function

    Format

    You can set the input method for the WEP encrypted key.
    ASCII: Input text. The method of inputting the encrypted WEP with text differs depending on the access point. Check with the network
    administrator for the network in which the projector participates, and then set to "ASCII".
    HEX: Input in hexadecimal.

    Key ID

    Selects the WEP encryption ID key.

    Encryption key 1/
    Encryption key 2/
    Encryption key 3/
    Encryption key 4

    You can enter the key used for WEP encryption. Enter the key in single-byte characters following instructions from the network administrator for
    the network in which the projector participates. The type of character and the number that can be entered differ according to the WEP encryption
    and Format settings.
    If the number of characters you enter is shorter than the required character length, no character is encrypted. If the number of characters you enter
    is longer than the required character length, characters that exceed the permitted number are not encrypted.
    128 Bit - ASCII: Single-byte alphanumerics, 13 characters.
    64 Bit - ASCII: Single-byte alphanumerics, 5 characters.
    128 Bit - HEX: 0 to 9 and A to F, 26 characters
    64 Bit - HEX: 0 to 9 and A to F, 10 characters

    Authentication Type

    You can set Authentication Type for WEP encoding.
    Open: Method to connect access point with no authentication.
    Shared: Authentication Type using WEP key.

    When WPA-PSK (TKIP) or WPA2-PSK (AES) are selected



  • Page 62

    List of Functions

    62

    The following items can be set.
    Sub Menu
    PSK (Encryption key)

    Function
    You can enter a Pre-Shared Key (encrypted key) in single-byte alphanumeric characters. Enter at least 8 and up to 63 characters. When the PreShared Key is entered and the [Enter] button is pressed, the value is set and displayed as an asterisk (*).
    You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 32 characters.
    s Projector Operation Guide "Changing Settings Using a Web Browser (Web Control)"

    When EAP-TLS is selected

    The following items can be set.
    Sub Menu
    Issued to/Issued by/Validity
    period

    Function
    Information in the certificate is displayed. You cannot enter.

    When EAP-TTLS/MD5, EAP-TTLS/MS-CHAPv2, PEAP/MS-CHAPv2, PEAP/GTC, LEAP, EAP-Fast/MS-CHAPv2 or EAP-FAST/GTC are selected

    The following items can be set.
    Sub Menu

    Function

    User name

    You can enter a user name to be used for authentication in single-byte alphanumeric characters (no spaces). You can enter up to 64 characters.
    You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 32 characters.
    s Projector Operation Guide "Changing Settings Using a Web Browser (Web Control)"

    Password

    You can enter an authentication password in single-byte alphanumeric characters. You can enter up to 64 characters. When the password is
    entered and the [Enter] button is pressed, the value is set and displayed as an asterisk (*).
    You cannot enter more than 32 characters on the configuration menu. When setting from Web Control, you can enter more than 32 characters.
    s Projector Operation Guide "Changing Settings Using a Web Browser (Web Control)"



  • Page 63

    List of Functions

    63

    Wired LAN Menu

    Sub Menu

    Function

    DHCP

    You can set whether or not (On/Off) to use DHCPg.
    If this is set to On you cannot set any more addresses.

    IP Address

    You can input the IP addressg assigned to the projector.
    You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
    0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)

    Subnet Mask

    You can input the Subnet Maskg for the projector. You can input a number from 0 to 255 in each field of the address. However, the following
    subnet masks cannot be used.
    0.0.0.0, 255.255.255.255

    Gateway Address

    You can input the IP address for the gateway for the projector.
    You can input a number from 0 to 255 in each field of the address. However, the following Gateway addressesg cannot be used.
    0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)

    MAC Address

    Displays the MAC address.

    IP Address Display

    To prevent the IP address from being displayed on the LAN Standby screen, set this to Off.



  • Page 64

    List of Functions

    64

    Mail Menu
    When this is set, you receive an e-mail notification if a problem or warning occurs in the projector. For information on the contents of the sent e-mail,
    s p.110

    Sub Menu

    Function

    Mail Notification

    You can set whether or not (On/Off) to be notified by e-mail.

    SMTP Server

    You can input the IP addressg for the SMTP server for the projector.
    You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
    127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)

    Port Number

    You can input the port number for the SMTP server. The default value is 25. You can input numbers between 1 to 65535.

    Email Address 1/Email
    Address 2/Email Address 3

    You can input the e-mail address of the destination to send the notification e-mail to. You can register up to three destinations. You can enter up to
    64 single-byte alphanumeric characters for the e-mail addresses. You cannot enter more than 32 characters on the configuration menu. When
    setting from Web Control, you can enter more than 32 characters.

    Setting a Notification Event

    You can select the problems or warnings to be notified about by e-mail. When the selected problem or warning occurs in the projector, an e-mail is
    sent to the specified Email Address notifying that a problem or warning has occurred. You can select multiple items from the displayed items.



  • Page 65

    List of Functions

    65

    Others Menu

    Sub Menu

    Function

    Trap IP Address 1/Trap IP
    Address 2

    You can register up to two for the SNMPg trap notification destination.
    You can input a number from 0 to 255 in each field of the address.
    However, the following IP addresses cannot be used.
    127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
    To use SNMP to monitor the projector, you need to install the SNMP manager program on your computer. SNMP should be managed by a
    network administrator.

    Priority gateway

    For the priority gateway, select either Wireless LAN or Wired LAN.

    AMX Device Discovery

    When the projector is connected to a network, set this to On to allow the projector to be detected by AMX Device Discoveryg. Set this to Off if
    you are not connected to an environment controlled with a controller from AMX or AMX Device Discovery.



  • Page 66

    List of Functions

    66

    Reset Menu
    Resets all of the network settings.

    Sub Menu
    Reset network settings.

    Function
    To reset all of the network settings, select Yes.
    After you reset all the settings, the Basic menu appears.



  • Page 67

    List of Functions

    67

    Info Menu (Display Only)
    Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the image
    signal being projected as shown in the following screen shots.
    Composite video g/S-Videog

    Analog RGB/Digital RGB/
    Component Videog/Digital Component Video

    Sub Menu

    Function

    Lamp Hours

    You can display the cumulative lamp operating time*.
    When it reaches the lamp warning time, the characters are displayed in yellow.

    Lamp Status

    The following icons show the status of the lamps.
    : Lighted
    When

    : Disable

    is displayed, the lamp is not operating normally. See "Reading the Indicators". s p.71

    Source

    You can display the Source name for the connected equipment currently being projected.

    Input Signal

    You can display the content of Input Signal set in the Signal menu according to the Source.

    Resolution

    You can display the Resolution.

    Video Signal

    You can display the content of Video Signal set in the Signal menu.

    Refresh Rate

    You can display the Refresh Rateg.

    Sync Info

    You can display the image signal Info.
    This information may be needed if service is required.

    Status

    This is Info about errors that have occurred on the projector.
    This information may be needed if service is required.



  • Page 68

    List of Functions

    68

    Sub Menu
    Serial Number
    *

    Function
    Displays the projector's serial number.

    The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours and above is displayed as "10H", "11H", and so on.

    Reset Menu

    Sub Menu
    Reset All

    Function
    You can reset all items in the configuration menu to their default settings.
    The following items are not reset to their defaults: Input Signal, User's Logo, Multi-screen, all items for Network menus, Lamp Hours, and
    Language.



  • Page 69

    Troubleshooting
    This chapter explains how to identify problems and what to do if a problem is found.



  • Page 70

    Using the Help
    If a problem occurs with the projector, the Help screen is displayed to
    assist you by pressing the [Help] button. You can solve problems by
    answering the questions.

    70

    C Confirm the selection.
    Remote Control

    Procedure

    A Press the [Help] button.
    The Help screen is displayed.
    Remote Control

    Questions and solutions are displayed as shown on the screen below.
    Press the [Help] button to exit Help.

    B Select a menu item.

    q
    Remote Control

    If the Help screen does not provide a solution to the problem,
    refer to "Problem Solving" p.71.



  • Page 71

    Problem Solving

    71

    If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
    If the indicators do not show clearly what the problem might be, refer to "When the Indicators Provide No Help". s p.75

    Reading the Indicators
    These indicators indicate the operating status of the projector.

    A Indicates the operating status.

    Standby condition
    When the [t] button is pressed in this condition, projection starts.
    Preparing network monitoring (maximum approx. 20 minutes) or cool down in progress
    Buttons are disabled while the indicator is flashing.
    Warming up
    Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
    [t] button does not function during warm-up.
    Projecting

    B Indicates the operating status of wireless LAN when the optional wireless LAN unit is connected. (EB-Z8050W only)
    C Indicates the air filter status.
    D Indicates the internal temperature status.



  • Page 72

    Problem Solving

    72

    E Indicates the projection lamp status.

    Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
    If all indicators are off, check that the power cable is connected correctly and that the power is being supplied normally.
    Sometimes, when the power cable is unplugged, the t indicator remains lit for a short period, but this is not a fault.

    t Indicator is lit or flashing red

    : Lit
    Status

    Cause

    : Flashing:

    : Off

    Remedy or Status

    Internal Error

    Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest
    address provided in the Support and Service Guide. s Epson Projector Contact List

    Fan Error
    Sensor Error
    Cool System Error

    Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest
    address provided in the Support and Service Guide.s Epson Projector Contact List

    High Temp Error
    (overheating)

    The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector
    switches to standby mode, so check the following two points.
    • Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
    • If the air filter is clogged, clean or replace it. s p.85, p.92
    If the error continues after checking the points above, stop using the projector, disconnect the power cable from the
    electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
    s Epson Projector Contact List
    When using at an altitude of 1500 m or more, set High Altitude Mode to On. s p.49
    Set Direction to Pointing Down or Pointing Up when the projector is installed to project downward or upward. s p.49

    Lamp Error
    Lamp Failure

    Check the following two points.
    • Take out the both lamps and check if they are cracked. s p.89
    • Clean the air filter. s p.85
    If it is not cracked: Re-fit the lamp and turn on the power.
    If the error continues: Replace the lamp with a new lamp and turn on the power.
    If the error continues: Stop using the projector, disconnect the power cable from the electrical outlet, and contact your
    local dealer or the nearest address provided in the Support and Service Guide. s Epson Projector Contact List



  • Page 73

    Problem Solving

    73

    Status

    Cause

    Remedy or Status
    If it is cracked: Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp yourself,
    be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is replaced). s Epson Projector
    Contact List
    When using at an altitude of 1500 m or more, set High Altitude Mode to On. s p.49
    Set Direction to Pointing Down or Pointing Up when the projector is installed to project downward or upward. s p.49

    Filter Airflow Error

    Check the following two points.
    • Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
    • If the air filter is clogged, clean or replace it. s p.85, p.92
    If the error continues after checking the points above, stop using the projector, disconnect the power cable from the
    electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
    s Epson Projector Contact List

    Auto Iris Error
    Cinema filter error
    Shutter Error
    Power Err. (Ballast)

    Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest
    address provided in the Support and Service Guide. s Epson Projector Contact List

    m o n Indicator is flashing or lit

    : Lit
    Status

    Cause

    : Flashing

    : Off

    : Varies according to the projector status

    Remedy or Status

    High Temp Warning

    (This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)
    • Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
    • If the air filter is clogged, clean or replace it. s p.85, p.92

    Replace Lamp

    The lamp indicated by flashing indicator, lamp 1 or 2, is due for replacement. Replace it with a new lamp. s p.89
    If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode
    increases. Replace it with a new lamp as soon as possible.
    We recommend replacing both lamps together to maintain consistent hue and brightness of projected images.

    Lamp Warning
    Supply System Warning (Ballast)

    Check the following two points.
    • Remove the lamp indicated by the flashing indicator, lamp 1 or 2, and check if it is cracked. s p.89
    • Clean the air filter. s p.85



  • Page 74

    Problem Solving

    Status

    74

    Cause

    Remedy or Status
    If it is not cracked: Re-fit the lamp and turn on the power.
    If the error continues: Replace the lamp with a new lamp and turn on the power.
    If the error continues: Stop using the projector, disconnect the power cable from the electrical outlet, and contact your
    local dealer or the nearest address provided in the Support and Service Guide. s Epson Projector Contact List
    If it is cracked: Replace it with a new lamp, or contact your local dealer for further advice. (Only one lamp is working.
    Replace the burned-out lamp as soon as possible.). s Epson Projector Contact List
    If replacing the lamp yourself, be careful to avoid pieces of broken glass.
    When using at an altitude of 1500 m or more, set High Altitude Mode to On. s p.49
    Set Direction to Pointing Down or Pointing Up when the projector is installed to project downward or upward. s p.49

    q

    No Air Filter
    Air Flow Sensor Err.

    Check that the air filter is securely installed. s p.92
    The projector automatically turns off about one minute after it detects that there is no air filter.
    If the error continues even though an air filter is installed, the air filter sensor may be defective. Stop using the projector,
    disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the
    Support and Service Guide. s Epson Projector Contact List

    Low Air Flow

    (This is not an abnormality. However, projection stops automatically if the airflow falls any further.)
    The message "The air filter is clogged. Clean or replace the air filter." is displayed. Check the following two points.
    • Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
    • If the air filter is clogged, clean or replace it. s p.85, p.92
    If the Low Air Flow continues to be low after cleaning the air filter, replace the air filter with a new one. s p.92
    If the error continues after checking the points above, stop using the projector, disconnect the power cable from the
    electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
    s Epson Projector Contact List

    Air Filter Notice

    "Time to clean the air filter. Clean or replace the air filter." is displayed. Clean the air filter. s p.85
    If the air filter is stained yellow with tobacco smoke and cannot be cleaned, replace it with a new one.
    The indicators or messages regarding "Air Filter Notice" are displayed only when Air Filter Notice is set to On, on the
    configuration menu's Extended menu. s p.49

    • If the projector is not operating properly, even though the indicators are all showing normal, refer to “When the Indicators Provide No Help”.
    s p.75
    • If the error is not indicated in this table, Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or
    the nearest address provided in the Support and Service Guide. s Epson Projector Contact List



  • Page 75

    Problem Solving

    When the Indicators Provide No Help
    If any of the following problems occur and the indicators do not offer
    a solution, refer to the pages given for each problem.

    Problems relating to images
    • "No images appear" s p.76
    Projection does not start, the projection area is completely black, the
    projection area is completely blue, and so on.
    • "Moving images are not displayed" s p.76
    Moving images being projected from a computer appear black and
    nothing is projected.
    • "Projection stops automatically" s p.76
    • "The message "Not supported" is displayed." s p.77
    • ""No Signal" is displayed." s p.77
    • "Images are fuzzy or out of focus" s p.77
    • "Interference or distortion appear in images" s p.78
    Problems such as interference, distortion, or black & white checked
    patterns appear.
    • "The image is truncated (large) or small, or the aspect is not suitable" s p.78
    Only part of the image is displayed, or the height and width ratios of the
    image are not correct, and so on.
    • "Image colors are not right" s p.79
    The whole image appears purplish or greenish, images are black & white,
    colors appear dull, and so on...(Computer monitors and LCD screens
    have different color reproduction performance, so that the colors
    projected by the projector and the colors appearing on the monitor may
    not necessarily match, but this is not a sign of a problem.)
    • "Images appear dark" s p.79

    Problems when projection starts
    • "No power supplied" s p.80

    75

    Other problems
    • "The Remote Control does not
    work" s p.81
    • "Nothing appears on the external
    monitor" s p.81
    • "I want to change the language for
    messages and menus" s p.81
    • "Mail is not received even if a problem
    occurs in the projector" s p.82



  • Page 76

    Problem Solving

    76

    Problems relating to images
    No images appear
    Check

    Remedy

    Did you press the [t] button?

    Press the [t] button to turn the power on.

    Are the indicators switched off?

    The power cable is not connected correctly or power is not being supplied normally.
    Connect the projector's power cable correctly. s Quick Start Guide
    Check that your electrical outlet or power source is functioning correctly.

    Is Shutter active?

    Press the [Shutter] button on the Remote Control to cancel Shutter. s p.24

    Are the configuration menu settings correct?

    Reset All of the settings. s Reset Menu - Reset All p.68

    Is the projected image completely black?

    Some input images, such as screen savers, may be completely black.

    Only when projecting computer images

    Is the image signal format setting correct?

    Change the setting according to the signal for the connected equipment. s Signal Menu - Video Signal p.46

    Only when projecting images from a video source

    Moving images are not displayed
    Check
    Is the computer's image signal being output to the LCD and the
    monitor?

    Remedy
    Change the image signal to external output only. s Check your computer's documentation.

    Only when projecting images from a laptop computer or a computer
    with a built-in LCD screen

    Projection stops automatically
    Check

    Remedy

    Is Sleep Mode set to On?

    Press the [t] button to turn the power on. If you do not want to use Sleep Mode, change the setting to Off.
    s Extended Menu - Operation - Sleep Mode p.49

    Is the air filter installed?

    Check that the air filter is securely installed. s p.92
    The projector automatically turns off about one minute after it detects that there is no air filter.



  • Page 77

    Problem Solving

    77

    The message "Not supported" is displayed.
    Check
    Is the image signal format setting correct?

    Remedy
    Change the setting according to the signal for the connected equipment. s Signal Menu - Video Signal p.46

    Only when projecting images from a video source

    Do the image signal Resolution and the Refresh Rate correspond
    to the mode?

    Refer to the computer's documentation for how to change the image signal Resolution and the Refresh Rate output
    from the computer. s "Supported Monitor Displays" p.114

    Only when projecting computer images

    "No Signal" is displayed.
    Check

    Remedy

    Are the cables connected correctly?

    Check that all the cables required for projection are securely connected. s Quick Start Guide

    Is the correct input port selected?

    Change the image by pressing the [Source Search] button on the Remote Control or the Control panel. s p.21

    Is the power for the computer or video source turned on?

    Turn the power on for the equipment.

    Are the image signals being output to the projector?

    If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to
    change the output to an external destination as well as the computer's own monitor. For some computer models,
    when the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor. s
    Computer's documentation, under a title such as "External output" or "Connecting an external monitor".
    If the connection is made while the power of the projector or computer is already turned on, the function [Fn] key
    that changes the computer's image signal to external output may not work. Turn the power for the computer and the
    projector off and then back on again.

    Only when projecting images from a laptop computer or a computer
    with a built-in LCD screen

    Images are fuzzy or out of focus
    Check

    Remedy

    Is the focus adjusted correctly?

    Press the [Focus] button on the remote control to adjust the focus. s Quick Start Guide

    Is the projector at the correct distance?

    Is it projecting outside of the recommended projection distance range?
    Setup within the recommended range. s p.103

    Is the Keystone adjustment value too large?

    Lower the projection angle to reduce the amount of keystone correction. s Quick Start Guide



  • Page 78

    Problem Solving

    78

    Check
    Has condensation formed on the lens?

    Remedy
    If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient
    temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to
    appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on the lens,
    turn the projector off and wait for the condensation to disappear.

    Interference or distortion appear in images
    Check
    Is the image signal format setting correct?

    Remedy
    Change the setting according to the signal for the connected equipment. s Signal Menu - Video Signal p.46

    Only when projecting images from a video source

    Are the cables connected correctly?

    Check that all the cables required for projection are securely connected. s Quick Start Guide

    Is an extension cable being used?

    If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector
    to check if the cables you are using may be causing the problem.

    Is the correct resolution selected?

    Set the computer so that the signals being output are compatible with the projector.
    s "Supported Monitor Displays" p.114 s Computer documentation

    Only when projecting computer images

    Are the "Sync.g" and "Trackingg" settings adjusted correctly?
    Only when projecting computer images

    Press the [Auto] button on the Remote Control or the [Enter] button on the Control panel to perform automatic
    adjustment. If the images are not adjusted correctly after using automatic adjustment, you can make the adjustments
    using Sync. and Tracking from the configuration menu. s Signal Menu - Tracking, Sync. p.46

    The image is truncated (large) or small, or the aspect is not suitable
    Check

    Remedy

    Is the aspect adjusted correctly?

    Press the [Aspect] button on the Remote Control to select an aspect suitable for the input source. s p.25

    Is a wide panel computer image being projected?

    Change the setting according to the signal for the connected equipment. s Signal Menu - Resolution p.46

    Only when projecting computer images

    Is the image still being enlarged by E-Zoom?

    Press the [ESC] button on the Remote Control to cancel E-Zoom. s p.31

    Is Position adjusted correctly?

    Press the [Auto] button on the Remote Control or the [Enter] button on the Control panel to perform automatic
    adjustment when the computer image is projected. If the images are not adjusted correctly after using automatic
    adjustment, you can make the adjustments using Position from the configuration menu.
    Apart from computer image signals, you can adjust other signals while projecting by adjusting Position from the
    configuration menu. s Signal Menu - Position p.46



  • Page 79

    Problem Solving

    79

    Check
    Is the computer set for dual display?
    Only when projecting computer images

    Is the correct resolution selected?
    Only when projecting computer images

    Remedy
    If dual display is activated in the "Display Properties" of the computer's Control panel, only about half of the image
    on the computer screen is projected. To display the entire image on the computer screen, turn off the dual display
    setting. s Computer video driver documentation
    Set the computer so that the signals being output are compatible with the projector.
    s "Supported Monitor Displays" p.114 s Computer documentation

    Image colors are not right
    Check

    Remedy

    Do the input signal settings match the signals from the connected
    device?

    Change the following settings according to the signal for the connected equipment.
    When image is from a device connected to the Computer or BNC input port s Signal menu - Input Signal p.46
    When image is from a device connected to the Video or S-Video input port s Signal menu - Video Signal p.46

    Is the image Brightness set correctly?

    Adjust the Brightness setting from the configuration menu. s Image Menu - Brightness p.44

    Are the cables connected correctly?

    Check that all the cables required for projection are securely connected. s Quick Start Guide

    Is Contrastg adjusted correctly?

    Adjust the Contrast setting from the configuration menu. s Image Menu - Contrast p.44

    Is the Color Adjustment correctly?

    Adjust the Color Adjustment setting from the configuration menu. s Image Menu - Color Adjustment p.44

    Are the Color Saturation and Tint adjusted correctly?

    Adjust the Color Saturation and Tint settings from the configuration menu. s Image Menu - Color Saturation,
    Tint p.44

    Only when projecting images from a video source

    Images appear dark
    Check

    Remedy

    Is the image Brightness set correctly?

    Adjust the Brightness and Power Consumption settings from the configuration menu.
    s Image Menu - Brightness p.44 s Settings Menu - Power Consumption p.48

    Is Contrastg adjusted correctly?

    Adjust the Contrast setting from the configuration menu.
    s Image Menu - Contrast p.44

    Is the lamp due for replacement?

    When the lamp is nearly ready for replacement, the images become darker and the color quality becomes
    poorer.When this happens, replace the lamp with a new lamp. s p.89



  • Page 80

    Problem Solving

    80

    Problems when projection starts
    No power supplied
    Check

    Remedy

    Did you press the [t] button?

    Press the [t] button to turn the power on.

    Are the indicators switched off?

    The power cable is not connected correctly or power is not being supplied normally.
    Disconnect and then reconnect the power cable. s Quick Start Guide
    Check that your electrical outlet or power source is functioning correctly.

    Do the indicators turn on and off when the power cable is touched? There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If
    this does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and
    contact your local dealer or the nearest address provided in the Support and Service Guide. s Epson Projector
    Contact List
    Is the Control Panel Lock set to Full Lock?

    Press the [t] button on the Remote Control. If you do not want to use Control Panel Lock, change the setting to
    Off. s Settings Menu - Control Panel Lock p.39

    Is the correct setting for the remote receiver selected?

    Check the Remote Receiver from the configuration menu. s Settings Menu - Remote Receiver p.48

    Was the power cable plugged back in or was the breaker turned on When the operation to the left is performed when Direct Power On is set to On, the power may not turn back on.
    immediately after Direct Power Off?
    Press the [t] button to turn the power back on.
    Is the ID switch on the side of the remote control set to On?

    When the switch is set to On, you can use the remote control to operate only a projector with a matching ID. Set ID
    switch to Off. s p.32

    Are the lamp cover and lamp installed correctly?

    If the lamp or lamp cover is installed incorrectly, the projector cannot be turned on. Check how it is installed.
    s p.89



  • Page 81

    Problem Solving

    81

    Other problems
    The Remote Control does not work
    Check

    Remedy

    Is the remote control light-emitting area pointing towards the
    remote receiver on the projector when it is operated?

    Point the remote control towards the Remote Receiver.
    Operating range s Quick Start Guide

    Is the remote control too far from the projector?

    The operating range for the remote control is about 15 m. s Quick Start Guide

    Is direct sunlight or strong light from fluorescent lamps shining
    onto the Remote Receiver?

    Set the projector up in a location where strong light does not shine onto the remote receiver. Or set the remote
    receiver to Off from Remote Receiver in the configuration menu. s Settings Menu - Remote Receiver p.48

    Is the correct setting for the remote receiver selected?

    Check the Remote Receiver from the configuration menu. s Settings Menu - Remote Receiver p.48

    Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary. s p.88
    Are the remote control ID and the projector ID matched?

    Make sure the ID for the projector you want to operate and the ID for the remote control match. To operate all
    projectors by remote control regardless of the ID setting, set the ID switch on the side of the remote control to Off.
    s p.32

    Does Remote Control Type match the remote control that you
    are using?

    Check the Remote Control Type on the configuration menu. s Extended Menu - Operation - Remote Control
    Type p.49

    Is the optional remote control cable connected to the remote
    control or to the projector's remote port?

    When the remote control cable is connected, the remote control light-emitting area or the projector's remote
    receiver are disabled. When not using the remote control cable set, disconnect it from the remote control and the
    remote port.

    Nothing appears on the external monitor
    Check

    Remedy

    Are images input from a port other than the Computer or
    BNC input port?

    The only images that can be displayed on an external monitor are computer images from the Computer
    or BNC input ports. s p.106

    I want to change the language for messages and menus
    Check
    Change the Language setting.

    Remedy
    Adjust the Language setting from the configuration menu. s Extended Menu - Language p.49



  • Page 82

    Problem Solving

    82

    Mail is not received even if a problem occurs in the projector
    Check

    Remedy

    Is Standby Mode set to Communication On?

    To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode
    from the configuration menu. s Extended Menu - Standby Mode p.49

    Did a fatal abnormality occur and the projector come to a sudden
    stop?

    When the projector comes to a sudden stop, e-mail cannot be sent.
    If the abnormal state continues, contact your local dealer or the nearest address provided in the Support and Service
    Guide. s Epson Projector Contact List

    Is power being supplied to the projector?

    Check that your electrical outlet or power source is functioning correctly.

    Is Mail function set correctly in the configuration menu?

    Mail notification of problems is sent according to the Mail settings in the configuration menu. Check if it is set
    correctly. s Reset Menu - Mail p.51



  • Page 83

    Appendix
    This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.



  • Page 84

    Installation Methods
    The projector can be mounted on a ceiling or placed on a desk as
    shown below. Also, this projector can project images to various places
    because it can project images vertically or horizontally at each 90˚ angle.

    84

    • Suspend the projector from the
    ceiling and project images from
    in front of a screen.

    • Suspend the projector from the
    ceiling and project images from
    behind a translucent screen.

    • Project images from in front of
    a screen.

    • Project images from behind a
    translucent screen.

    • Project images directly up

    • Project images directly down

    Warning
    • A special method is required when installing the projector to project images
    downward (ceiling mount) or upward. If installation work is not carried
    out correctly, the projector could fall down. This may result in injury or
    accidents.
    Contact your dealer or the nearest address provided in the Support and
    Service Guide if you want to use this installation method. s Epson
    Projector Contact List
    • If you use adhesives on the Ceiling mount fixing points to prevent the
    screws from loosening, or if you use things such as lubricants or oils on
    the projector, the projector case may crack causing it to fall from its
    ceiling mount. This could cause serious injury to anyone under the ceiling
    mount and could damage the projector.
    When installing or adjusting the Ceiling mount, do not use adhesives to
    prevent the screws from loosening and do not use oils or lubricants and so
    on.
    • When mounting the projector on the ceiling, be sure to arrange measures
    to prevent it from falling such as passing a wire through the handles.

    Attention
    • Do not install the projector at any angles other than those shown in the
    following illustrations.
    • Do not use the projector upside down.
    • Set the Direction properly in the configuration menu according to the angle
    of installation. s p.49
    • Using the projector at an improper angle or if the configuration menu
    settings are wrong causes malfunctions and shortens the operating life of
    optical parts.

    q

    • An optional Ceiling mount is required when suspending the
    projector from a ceiling.
    s p.94
    • The Projection can be changed from the configuration menu.
    s p.49



  • Page 85

    Cleaning
    You should clean the projector if it becomes dirty or if the quality of
    projected images starts to deteriorate.

    Warning
    Do not use sprays containing a flammable gas to remove dirt or dust which
    is adhering to parts such as the lens or filter of the projector.
    This coud be a cause of the fire for the high temperature of lamps inside
    the unit.

    85

    Cleaning the Air filter
    Clean the air filter and the air intake vent when the following message
    is displayed or the Filter indicator is flashing green.
    "Time to clean the air filter."
    "Clean or replace the air filter."

    Attention
    • If dust collects on the air filter it can cause the internal temperature of

    Cleaning the Projector's Surface
    Clean the projector's surface by wiping it gently with a soft cloth.
    If the projector is particularly dirty, moisten the cloth with water
    containing a small amount of neutral detergent, and then firmly wring
    the cloth dry before using it to wipe the projector's surface.

    the projector to rise, and this can lead to problems with operation and
    shorten the optical engine's service life. Clean the air filter immediately
    when the message is displayed.
    • If the air filter is stained yellow with tobacco smoke, it cannot be cleaned.
    In this case, replace it with a new air filter. s p.92
    • Do not rinse the air filter in water. Do not use detergents or solvents.
    • When using a brush for cleaning, use one with long soft bristles, and
    brush it lightly. If it is brushed too strongly, dust will be ground into the
    air filter and cannot be removed.

    Attention
    Do not use volatile substances such as wax, alcohol, or thinner to clean the
    projector's surface. The quality of the case may change or become discolored.

    Procedure

    A After you turn off the projector's power and the

    confirmation buzzer beeps twice, disconnect the power cable.

    Cleaning the Lens
    Use a commercially available cloth for cleaning glasses to gently wipe
    the lens.

    Attention
    Do not rub the lens with harsh materials or subject the lens to shocks, as it
    can easily become damaged.

    B Remove the air filter cover.
    Grip the air filter cover tab between your fingers, and pull up
    and remove the cover while pressing the tab.



  • Page 86

    Cleaning

    C Remove the air filter.

    86

    Attention
    If the air filter is hit too hard, it may become unusable due to deformities
    and cracks.

    E Remove any dust remaining on the air filter by using a
    vacuum cleaner from the front side.

    D With the front (the side with tabs) of the air filter facing

    down, tap the air filter four or five times to shake off the
    dust.
    Turn it over and tap the other side in the same way.

    F Replace the air filter.



  • Page 87

    Cleaning

    87

    G Replace the air filter cover.
    Press the cover until it clicks into place.

    q

    If a message is frequently displayed, even after cleaning, it is time
    to replace the air filter. Replace it with a new air filter. s p.92



  • Page 88

    Replacing Consumables

    88

    This section explains how to replace the Remote Control batteries, the
    lamp, and the air filter.

    Replacing the Remote Control Batteries
    If delays in the responsiveness of the Remote Control occur or if it
    does not operate after it has been used for some time, it probably
    means that the batteries are becoming flat. When this happens, replace
    them with new batteries. Have two AA size alkaline batteries ready. You
    cannot use other batteries except for the AA size alkaline.

    Attention
    Make sure you read the Safety Instructions before handling the batteries. s
    Safety Instructions

    Procedure

    A Remove the battery cover.
    While pushing the battery compartment cover catch, lift the cover
    up.

    B Replace the old batteries with new batteries.

    Caution
    Check the positions of the (+) and (-) marks inside the battery holder to
    ensure the batteries are inserted the correct way.

    C Replace the battery cover.
    Press the battery compartment cover until it clicks into place.



  • Page 89

    Replacing Consumables

    Replacing the Lamp
    Lamp replacement period
    It is time to replace the lamp when:
    • The message "Replace the lamp." is displayed at the lower left of the
    projection screen when you start projecting.

    89

    • The projected image gets darker or starts to deteriorate.

    Attention
    • The lamp replacement message is set to appear after the following time
    periods in order to maintain the initial brightness and quality of the
    projected images. s p.48
    When using Power Consumption continually at Normal: About 2400 hours
    When using Power Consumption continually at ECO: About 3400 hours

    • Do not turn the projector on immediately after turning it off. Turning the
    projector on and off frequently may shorten the life of the lamps.

    • If you continue to use the lamp after the replacement period has passed,
    the possibility that the lamp may explode increases. When the lamp
    replacement message appears, replace the lamp with a new one as soon as
    possible, even if it is still working.

    • Depending on the characteristics of the lamp and the way it has been

    • The lamp indicator flashes orange.
    Replace the lamp indicated by the flashing indicator, either lamp 1 or
    2.

    used, the lamp may become darker or stop working before the lamp
    warning message appears. You should always have two spare lamp units
    ready in case they are needed.

    How to replace the lamp
    The lamp can be replaced even when the projector is suspended from a
    ceiling.

    Warning
    • When replacing the lamps because they have stopped illuminating, there is
    a possibility that the lamp may be broken. If replacing the lamp of a
    projector which has been installed on the ceiling, you should always
    assume that the lamp is broken, and you should stand to the side of the
    lamp cover, not underneath it. Remove the lamp cover gently.
    • Never disassemble or remodel the lamp. If a remodeled or reassembled
    lamp is installed into the projector and used, it could cause a fire, electric
    shock, or an accident.



  • Page 90

    Replacing Consumables

    Caution
    Wait until the lamps have cooled down sufficiently before removing the lamp
    cover. If the lamp is still hot, burns or other injuries may result. It takes
    about one hour after the power has been turned off for the lamp to be cool
    enough.

    90

    C Pull up the lock lever for the lamp you want to replace and
    pull the lamp straight out.
    If the lamp is cracked, replace it with a new lamp, or contact
    your local dealer for further advice. s Epson Projector Contact
    List

    Attention
    • Never use the projector unless there are two lamps installed.
    • We recommend replacing both lamps together to maintain consistent hue
    and brightness of projected images.

    Procedure

    A After you turn off the projector's power and the

    confirmation buzzer beeps twice, disconnect the power cable.

    B Wait until the lamps have cooled down sufficiently before

    removing the lamp cover on the back of the projector.
    Pinch the tabs on the front of the lamp cover together to release
    the lock. When the lock releases, pull the cover straight out.

    A Lamp 1
    B Lamp 2

    D Install the new lamp.
    Insert the new lamp along the guide rail in the correct direction
    so that it fits in place, push firmly until it is fully inserted, and
    pull down the lock lever until it clicks into place.



  • Page 91

    Replacing Consumables

    91

    Attention
    • Make sure you install the lamp securely. If the lamp cover is removed, the
    lamp turns off automatically as a safety precaution. If the lamp or the
    lamp cover is not installed correctly, the lamp does not turn on.
    • This product includes a lamp component that contains mercury (Hg).
    Please consult your local regulations regarding disposal or recycling. Do not
    dispose of it with normal waste.

    Resetting the Lamp Hours
    The projector records how long the lamps are turned on and a message
    and indicator notify you when it is time to replace the lamp. After
    replacing the lamps and turning on the power, the following message is
    displayed on the screen and you can reset the lamp-hour counter.
    Select Yes, and then press the [Enter] button.

    E Replace the lamp cover.
    Press the cover against the unit and slide it to the right until it
    clicks.

    A Displays the replacement for the lamp 1.
    B Displays the cumulative lamp operating time. If you select Yes and reset
    the Lamp Hours, the count for lamp 1 is set to 0H.



  • Page 92

    Replacing Consumables

    92

    Replacing the Air Filter
    Air filter replacement period
    It is time to replace the air filter when:
    • The air filter has turned brown.
    • The message is displayed even though the air filter has been cleaned.

    How to replace the air filter
    The air filter can be replaced even when the projector is suspended
    from a ceiling.

    C Remove the air filter.

    Procedure

    A After you turn off the projector's power and the

    confirmation buzzer beeps twice, disconnect the power cable.

    B Remove the air filter cover.
    Grip the air filter cover tab between your fingers, and pull up
    and remove the cover while pressing the tab.

    D Install the new air filter.



  • Page 93

    Replacing Consumables

    E Replace the air filter cover.
    Press until it clicks into place.

    q

    Dispose of used air filters properly in accordance with your local
    regulations.
    Material of the frame part: Polypropylene
    Material of the filter part: Polypropylene

    93



  • Page 94

    Optional Accessories and Consumables
    The following optional accessories and consumables are available. Please
    purchase these products as and when needed. The following list of
    optional accessories and consumables is current as of: 2009.07. Details
    of accessories are subject to change without notice and availability may
    vary depending on the country of purchase.

    Optional accessories
    Computer cable ELPKC02
    (1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
    This is the same as the computer cable supplied with the projector.

    Computer cable ELPKC09
    (3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
    Computer cable ELPKC10
    (20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
    Use one of these longer cables if the computer cable supplied with the
    projector is too short.

    94

    Long focus zoom lens ELPLL07
    (Projection distance ratio: a. Approx. 5.76
    5.83 to 8.18)
    Medium focus zoom lens ELPLM07
    (Projection distance ratio: a. Approx. 3.85
    3.92 to 5.97)
    Medium focus zoom lens ELPLM06
    (Projection distance ratio: a. Approx. 2.64
    2.68 to 4.10)
    Standard focus zoom lens ELPLS04
    (Projection distance ratio: a. Approx. 1.71
    1.74 to 2.82)
    Short focus wide lens ELPLW04
    (Projection distance ratio: a. Approx. 1.29
    1.31 to 1.80)
    Wide lens for rear projection ELPLR04
    (Projection distance ratio: a. Approx. 0.76

    to 8.09 b. Approx.

    to 5.88 b. Approx.

    to 4.03 b. Approx.

    to 2.78 b. Approx.

    to 1.77 b. Approx.

    b. Approx. 0.77)

    Use to connect a Component Videog source.

    a: EB-Z8050W b: EB-Z8000WU
    Projection distance ratio = projection distance/projection screen width
    The values are installation standards. They are subject to change depending
    on projection conditions.

    Remote control cable set ELPKC28
    (10m 2 piece set)

    Low ceiling mount* ELPMB25
    High ceiling mount * ELPMB26

    Use this to guarantee operation from the remote control from a distance.

    Use when installing the projector on a ceiling.

    Component video cable ELPKC19
    (3 m - for mini D-Sub 15-pin/RCA male^3)

    Wireless mouse receiver ELPST16
    Use this to operate a computer's mouse pointer using the projector's remote
    control, or to operate page Up/Down while projecting a PowerPoint file.

    Wireless LAN unit ELPAP03 (for EB-Z8050W)
    Use this to project images from a computer via a wireless LAN.

    *

    A special method of installation is required to suspend the projector from
    a ceiling. Contact your dealer or the nearest address provided in the
    Support and Service Guide if you want to use this installation method.
    s Epson Projector Contact List



  • Page 95

    Optional Accessories and Consumables

    Consumables
    Replacement lamp unit (two-pack) ELPLP52
    Replacement lamp unit (one-pack) ELPLP51
    Use as a replacement for used lamps.

    Air filter ELPAF23
    Use as a replacement for used air filters.

    95



  • Page 96

    Notes on Transportation
    There are many glass parts and precision components inside the
    projector. To prevent damage due to impacts when transporting, handle
    the projector as follows.

    Moving Nearby
    Checking the following points, and then carry carefully by the handles.
    • Turn off the power to the projector and disconnect all cables.
    • Attach the lens cover to the lens.
    • Store the foot.

    Caution
    Do not carry the projector by one person.
    Two people are needed to unpack or carry the projector.

    When Transporting
    Preparing packaging
    After checking the points in "Moving Nearby", prepare the following
    and then pack up the projector.
    • Remove the lens unit if an option lens, other than the standard
    zoom lens, is installed. Attach the standard zoom lens if the projector
    has a built-in lens. If the projector does not have a lens, attach the
    cover that was on the lens mount when you purchased the projector.
    • The vertical and horizontal lens shifts are positioned in the center.
    • Fit the protective lens pad that was used at the time of purchase.

    96

    Notes when packing and transporting
    Enclose the projector securely in buffer material to protect it from
    shock, and place it into a strong cardboard container. Be sure to notify
    the carrier company that the contents are fragile.



  • Page 97

    Saving a User's Logo

    97

    You can save the image that is currently being projected as a User's Logo.

    q

    When a User's Logo is saved, the previous User's Logo is erased.

    q

    Procedure

    A Project the image you want to use as the User's Logo, and
    then press the [Menu] button.
    Using the Remote Control

    • If User's Logo Protect from Password Protect is set to On, a
    message is displayed and the user's logo cannot be changed. You
    can make changes after setting User's Logo Protect to Off.
    s p.37
    • If User's Logo is selected when Keystone, E-Zoom, Aspect, or
    Progressive are being performed, the function currently being
    performed is cancelled.

    C When "Choose this image as the User's Logo?" is displayed,
    select "Yes".

    Using the Control panel

    q

    B Select Extended - "User's Logo" from the configuration

    menu. s "Using the Configuration Menu"
    Check the buttons you can use and the operations they perform
    in the guide under the menu.

    When you press the [Enter] button on the Remote Control or the
    Control panel, the screen size may change according to the signal
    as it changes to the resolution of the image signal.



  • Page 98

    Saving a User's Logo

    98

    D Move the box to select the part of the image to use as the
    User's Logo.

    F Select the zoom factor from the zoom setting screen.

    400% is displayed only when using EB-Z8000WU.

    G When the message "Save this image as the User's Logo?" is

    displayed, select "Yes".
    The image is saved. After the image has been saved, the message
    "Completed." is displayed.

    Using the Remote Control

    Using the Control panel

    q

    q

    You can save at up to 400 ^ 300 dots in size.

    E When "Select this image?" is displayed, select "Yes".

    • Once a User's Logo has been saved, the logo cannot be returned
    to the factory default.
    • Saving the user's logo may take approximately 15 seconds. Do
    not use the projector or any connected equipment while it is
    saving, otherwise malfunctions may occur.



  • Page 99

    Making a WPS (Wi-Fi Protected Setup) Connection with a Wireless LAN Access Point (EB-Z8050W only)
    There are two methods for setting WPS.
    • Push Button Method
    SSID and security are set automatically when the [Enter] button is
    pressed on the projector's control panel and the dedicated button on
    the access point equipment. This method is recommended when the
    projector and access point are close together.
    • PIN Code Method
    SSID and security are set automatically by inputting an 8-digit code
    that was assigned to the projector from the computer to the access
    point in advance. Make connection settings between the computer and
    the access point in advance. For details on how to make this
    connection, refer to the manual provided with the access point. This
    method is recommended when the projector is mounted on the ceiling.

    99

    B From "Wireless LAN" select "To Setup Wizard".

    The following screen is displayed.

    Connection Setup Method
    Procedure

    A During projection, press the [Menu] button and select

    Network - "Network Configuration" from the configuration
    menu.
    When connecting using the Push Button Method, follow the steps
    given below.
    Go to "Making a connection using the PIN Code Method" when
    connecting using the "PIN Code Method". s p.101

    Making a Connection Using the Push Button Method
    Procedure
    The Network Configuration screen is displayed.

    A Select "Push Button Method".



  • Page 100

    Making a WPS (Wi-Fi Protected Setup) Connection with a Wireless LAN Access Point (EB-Z8050W only)

    The Push Button Method screen is displayed.

    B Press the [Enter] button on the projector's control panel
    when prompted by the screen.

    This completes the setup.

    D Press the [Enter] button or the [Esc] button.

    It returns to the Wireless LAN menu screen.
    Then, the Push Button Method screen is displayed.

    C Press the button on the access point when prompted by the
    screen.

    E Select "Yes" from "Setup complete".

    100



  • Page 101

    Making a WPS (Wi-Fi Protected Setup) Connection with a Wireless LAN Access Point (EB-Z8050W only)

    The PIN Code Method screen is displayed.
    This completes the setup of the connection between the projector
    and the access point. Press the [Menu] button to close the
    configuration menu.

    B Enter the PIN code displayed on the "PIN Code Method"
    screen from the computer to the access point, and then
    select "Start Setup".

    Making a connection using the PIN Code Method

    q

    Before you can make a connection using the "PIN Code Method",
    a connection must have already been setup between the computer
    and the access point.

    Procedure

    A Select "PIN Code Method".

    The progress is displayed.

    101



  • Page 102

    Making a WPS (Wi-Fi Protected Setup) Connection with a Wireless LAN Access Point (EB-Z8050W only)

    C The message "Setup by Wi-Fi Protected Setup complete." is
    displayed. Press the [Enter] button or the [Esc] button.

    It returns to the Wireless LAN menu screen.

    D Select "Yes" from "Setup complete".

    102

    This completes the setup of the connection between the projector
    and the access point. Press the [Menu] button to close the
    configuration menu.



  • Page 103

    Screen Size and Projection Distance

    103

    The following table shows the projection distance when a standard
    zoom lens is attached. When an optional lens is attached, check the
    projection distances in the User's Guide supplied with optional lenses.
    To find the appropriate screen size, see the following table to set up
    the projector. Values are just reference.

    4:3
    Screen Size

    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    300"

    610x460

    1288 - 2081

    -97 - 554

    440"

    890x670

    1898 - 3062

    -142 - 814

    Units: cm
    16:9
    Screen Size

    A Projection distance
    B is the distance from the center of the lens to the base of the screen. This changes
    depending on the setting for vertical lens shift.
    C Center of lens

    Projection Distance of EB-Z8000WU

    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    60"

    130x75

    227 - 371

    -22 - 96

    80"

    180x100

    306 - 498

    -29 - 129

    100"

    220x120

    384 - 624

    -36 - 161

    120"

    270x150

    463 - 751

    -43 - 193

    150"

    330x190

    580 - 940

    -54 - 241

    200"

    440x250

    777 - 1256

    -72 - 321

    300"

    660x370

    1169 - 1888

    -108 - 482

    485"

    1070x600

    1899 - 3064

    -176 - 781

    Units: cm
    Units: cm
    4:3
    Screen Size

    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    16:10
    Screen Size

    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    130x81

    221 - 361

    -17 - 98

    80"

    180x110

    297 - 484

    -23 - 130

    -39 - 221

    100"

    220x130

    374 - 607

    -28 - 163

    640 - 1036

    -48 - 277

    120"

    270x169

    450 - 730

    -34 - 196

    856 - 1384

    -64 - 369

    150"

    330x206

    564 - 915

    -43 - 245

    60"

    120x90

    251 - 410

    -19 - 111

    80"

    160x120

    338 - 549

    -26 - 148

    60"

    100"

    200x150

    424 - 688

    -32 - 185

    120"

    240x180

    510 - 828

    150"

    300x230

    200"

    410x300



  • Page 104

    Screen Size and Projection Distance

    16:10
    Screen Size

    104

    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    16:9
    Screen Size

    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    200"

    440x275

    755 - 1222

    -57 - 326

    80"

    180x100

    301 - 490

    -28 - 127

    300"

    550x344

    1137 - 1837

    -85 - 489

    100"

    220x120

    378 - 614

    -35 - 159

    500"

    1100x688

    1900 - 3067

    -142 - 815

    120"

    270x150

    455 - 739

    -42 - 191

    150"

    330x190

    571 - 925

    -52 - 239

    200"

    440x250

    764 - 1236

    -69 - 318

    300"

    660x370

    1150 - 1859

    -104 - 477

    485"

    1070x600

    1869 - 3016

    -168 - 773

    Projection Distance of EB-Z8050W
    Units: cm
    4:3
    Screen Size

    Units: cm
    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    60"

    120x90

    247 - 403

    -18 - 110

    80"

    160x120

    332 - 540

    -24 - 146

    100"

    200x150

    417 - 677

    -30 - 183

    120"

    240x180

    502 - 814

    -37 - 219

    150"

    300x230

    630 - 1020

    -46 - 274

    200"

    410x300

    843 - 1363

    -61 - 366

    300"

    610x460

    1268 - 2048

    -91 - 549

    440"

    890x670

    1868 - 3014

    -134 - 807

    Units: cm
    16:9
    Screen Size
    60"

    130x75

    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    224 - 365

    -21 - 95

    16:10
    Screen Size

    Minimum (Wide) to Maximum (Tele)

    Vertical lens shift
    Top to Bottom

    60"

    130x81

    217 - 355

    -16 - 97

    80"

    180x110

    292 - 476

    -22 - 129

    100"

    220x130

    368 - 597

    -27 - 162

    120"

    270x169

    443 - 719

    -32 - 194

    150"

    330x206

    555 - 900

    -40 - 242

    200"

    440x275

    743 - 1203

    -54 - 323

    300"

    550x344

    1119 - 1808

    -81 - 485

    500"

    1100x688

    1870 - 3019

    -135 - 808



  • Page 105

    Connecting a LAN Cable
    Connect with a commercially available 100BASE-TX or 10BASE-T LAN
    cable. The interface may differ from the following illustration depending
    on the model of your projector. (The following illustration indicates
    EB-Z8000WU)

    A To LAN port
    B LAN cable (commercially available)
    C To LAN port

    Attention
    To prevent malfunctions, use a category 5 shielded LAN cable.

    105



  • Page 106

    Connecting to an external monitor
    Analog RGB images input from Computer Input Port or BNC Input
    Port can be displayed on an external monitor and the screen at the
    same time. This means that you can check projected images on an
    external monitor when giving presentations even if you cannot see the
    screen. Connect using the cable supplied with the external monitor.

    A To Monitor Out port
    B Cable supplied with monitor
    C To Monitor port

    q

    • Component video signals and computer or video equipment
    connected to the input ports other than Computer input port
    and BNC input port cannot be output to an external monitor.
    • Setting gauges such as Keystone, the configuration menu, or Help
    screens are not output to the external monitor.

    106



  • Page 107

    Removing and Attaching the Projector Lens Unit
    Prepare #2 plus-driver in advance.

    107

    B Remove the front cover.

    Removing
    Attention
    • Only remove the lens unit when necessary. If dust or dirt enter the
    projector, projection quality deteriorates and it could cause a malfunction.

    • Try not to touch the lens section with your hand or fingers.
    If fingerprints or oils are left on the surface of the lens, projection quality
    deteriorates.
    • If the lens shift has been done, set the lens shift to the center before
    replacing the lens unit.

    Procedure

    A Remove the interface cover.

    A Loosen the two fixing screws.
    B Loosen the fixing screw.
    C Pull the cover straight out.

    C Pinch the lock lever of the lens unit and turn it
    counterclockwise.

    A Loosen the fixing screw.
    B While pulling up the interface cover open switch, pull the interface cover
    straight out.



  • Page 108

    Removing and Attaching the Projector Lens Unit

    D Pull the lens unit straight out as it is released.
    Attaching
    Attention
    Do not attach the lens unit when the projector's lens insertion section is
    facing up. Dust or dirt could enter the projector.

    Procedure

    A Insert the lens unit straight into the lens insertion section
    with the white circle on the lens on top.

    108

    B While holding the lens unit firmly, turn the lock lever

    clockwise until it is locked. Check that the lens cannot be
    detached.



  • Page 109

    Removing and Attaching the Projector Lens Unit

    109

    A Install the cover along the guide.
    B Tighten the fixing screws.

    C Replace the front cover.

    Attention
    • Install the front cover to use the projector.
    • Store the projector with the lens unit installed.
    If the projector is stored without the lens unit, dust and dirt may get
    inside the projector and cause malfunctions or lower the quality of projection.

    A Install the cover along the guide.
    B Tighten the fixing screw.
    C Tighten the two fixing screws.

    D Replace the interface cover.



  • Page 110

    Reading Problem Mail Notification Function
    When the Mail Notification function is set to On and a problem/
    warning occurs in the projector, the following e-mail is sent.
    Subject: EPSON Projector
    Line 1: The name of the projector where the problem has occurred
    Line 2: The IP address set for the projector where the problem has
    occurred.
    Line 3 and on: Details of the problem
    The details of the problem are listed line by line. The following table
    shows the details that are given in the message for each item. To deal
    with problems/warnings, see "Reading the Indicators" s p.71
    Message

    Cause

    110

    Message

    Cause

    Low Air Flow

    Low Air Flow

    Low Air Flow Error

    Filter Airflow Error

    No Air Filter

    No Air Filter/Air Flow Sensor Err.

    No-signal

    No Signal
    No Signal is input to the projector.
    Check the connection status or check
    that the power for the signal source is
    turned on.

    Peltier Device error

    Cooling system error (Peltier element)

    Power Err. (Ballast)

    Power Err. (Ballast)

    Auto Iris Error

    Auto Iris Error

    Cinema filter error

    Cinema filter error

    Power Warning. (Ballast) (1)
    Power Warning. (Ballast) (2)

    Cinema Filter Warning

    Cinema Filter Warn.
    The projector can still be used but the
    cinema filter does not work.

    Supply System Warning (Ballast)
    (1) indicates the lamp 1, and (2)
    indicates the lamp 2. The informed
    lamp is out.

    Pump Error

    Cooling system error (pump)

    Clean Air Filter

    Air Filter Notice

    Sensor error

    Sensor Error

    Fan related error

    Fan Error

    Shutter Error

    Shutter Error

    High-speed cooling in progress

    High Temp Warning

    Shutter Warning

    Internal error

    Internal Error

    Internal temperature error

    High Temp Error
    (Overheating)

    Shutter Warning
    Though this unit still can be used, the
    electric shutter does not work.

    Lamp out

    Lamp Error (both lamps 1/2)

    Lamp replacement notification (1)
    Lamp replacement notification (2)

    Replace Lamp
    (1) Indicates lamp 1, and (2) indicates
    lamp 2. The informed lamp is due for
    replacement.

    Lamp timer failure

    Lamp Failure (both lamp 1/2)

    Lamp Warning (1)
    Lamp Warning (2)

    Lamp Warning
    (1) indicates lamp 1, and (2) indicates
    lamp 2. The informed lamp is out.

    A (+) or (-) appears at the start of the message.
    (+): A projector problem has occurred
    (-): A projector problem has been dealt with



  • Page 111

    ESC/VP21 Commands

    111

    Command List

    Cable Layouts

    When the power ON command is transmitted to the projector, the
    power turns on and it enters warm-up mode. When the projector's
    power has turned on, a colon ":" (3Ah) is returned.
    When a command is input, the projector executes the command and
    returns a ":", and then accepts the next command.
    If the command being processed terminates abnormally, an error
    message is output and a ":" is returned.
    Item
    Power ON/OFF
    Signal selection

    PWR ON

    Off

    PWR OFF

    BNC

    Shutter On/Off

    • Connector shape: D-Sub 9-pin (male)
    • Projector input port name: RS-232C
    <At the projector>

    <At the computer>

    Command

    On
    Computer

    Serial Connection

    Auto

    SOURCE 1F

    RGB

    SOURCE 11

    Component

    SOURCE 14

    Auto

    SOURCE BF

    RGB

    SOURCE B1

    Component

    SOURCE B4

    HDMI

    SOURCE A0

    DVI-D

    SOURCE 30

    Video

    SOURCE 45

    S-Video

    SOURCE 42

    On

    MUTE ON

    Off

    MUTE OFF

    Add a Carriage Return (CR) code (0Dh) to the end of each command and
    transmit.

    <At the projector>

    (PC serial cable)

    Signal Name

    Function

    GND

    Signal wire ground

    TD

    Transmit data

    RD

    Receive data

    <At the computer>



  • Page 112

    ESC/VP21 Commands

    Communications protocol






    Default baud rate setting: 9600 bps
    Data length: 8 bit
    Parity: None
    Stop-bit: 1 bit
    Flow control: None

    112



  • Page 113

    About PJLink

    113

    PJLink Class1 was established by the JBMIA (Japan Business Machine
    and Information System Industries Association) as a standard protocol
    for controlling network-compatible projector's as part of their efforts to
    standardize projector control protocols.
    The projector complies with the PJLink Class1 standard established by
    the JBMIA.
    It complies with all commands except for the following commands
    defined by PJLink Class1, and agreement was confirmed by the PJLink
    standard adaptability verification.
    URL: http://pjlink.jbmia.or.jp/english/
    • Non-compatible commands
    Function
    Image muting set

    PJLink Command
    AVMT 11

    • Input names defined by PJLink and corresponding projector sources
    Source

    PJLink Command

    Computer

    INPT 11

    BNC

    INPT 13

    Video

    INPT 23

    S-Video

    INPT 22

    DVI-D

    INPT 31

    HDMI

    INPT 32

    • Manufacturer name displayed for "Manufacture name information query"
    EPSON

    • Model name displayed for "Product name information query"
    EB-Z8050W/PowerLite Pro Z8050W
    EB-Z8000WU/PowerLite Pro Z8000WU



  • Page 114

    Supported Monitor Displays

    114

    Supported Monitor Displays for EB-Z8000WU
    Computer signals (analog RGB)
    Units: dots
    Signal

    Refresh Rate (Hz)

    VGA

    60/72/75/85/iMac*1

    SVGA

    Resolution

    Aspect Mode
    Normal

    16:9

    Full

    Zoom

    Native

    640x480

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    640x480

    56/60/72/75/85/iMac*1

    800x600

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    800x600

    XGA

    60/70/75/85/iMac*1

    1024x768

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    1024x768

    WXGA

    60/75/85

    1280x768

    1920x1152

    1920x1080

    1920x1200

    1920x1152

    1280x768

    60

    1360x768

    1920x1084

    1920x1080

    1920x1200

    1920x1084

    1360x768

    60/75/85

    1280x800

    1920x1200

    1920x1080

    1920x1200

    1920x1200

    1280x800

    WXGA+

    60/75/85

    1440x900

    1920x1200

    1920x1080

    1920x1200

    1920x1200

    1440x900

    WSXGA+

    60

    1680x1050

    1920x1200

    1920x1080

    1920x1200

    1920x1200

    1680x1050

    SXGA

    70/75/85

    1152x864

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    1152x864

    60/75/85

    1280x1024

    1500x1200

    1920x1080

    1920x1200

    1920x1200

    1280x1024

    60/75/85

    1280x960

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    1280x960

    SXGA+

    60*2/75/85

    1400x1050

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    1400x1050

    UXGA

    60

    1600x1200

    1600x1200

    Non-compatible

    1920x1200

    1920x1200

    1600x1200

    WUXGA*3

    60

    1920x1200

    1920x1200

    1920x1080

    1920x1200

    1920x1200

    1920x1200

    MAC13”

    67

    640x480

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    640x480

    MAC16”

    75

    832x624

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    832x624

    MAC19”

    75

    1024x768

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    1024x768

    60

    1024x768

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    1024x768



  • Page 115

    Supported Monitor Displays

    Signal
    MAC21”

    Refresh Rate (Hz)
    75

    115

    Resolution
    1152x870

    Aspect Mode
    Normal

    16:9

    Full

    Zoom

    Native

    1588x1200

    1920x1080

    1920x1200

    1920x1200

    1152x870

    *1 Connection is disabled if the equipment does not have a VGA output port.
    *2 Only compatible when Normal is selected as the Resolution from the configuration menu.
    *3 Only compatible when VESA CVT-RB(Reduced Blanking) signal is input.
    Even when signals other than those mentioned above are input, it is likely that the image can be projected. However, not all functions may be supported.

    Component Video
    Units: dots
    Signal

    Refresh Rate (Hz)

    Resolution

    Aspect Mode
    Normal

    16:9

    Full

    Zoom

    Native

    SDTV(480i)

    60

    720x480

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    640x480

    SDTV(576i)

    50

    720x576

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    768x576

    SDTV(480p)

    60

    720x480

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    640x480

    SDTV(576p)

    50

    720x576

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    768x576

    HDTV(720p)

    50/60

    1280x720

    1920x1080

    1920x1080

    1920x1200

    1920x1080

    1280x720

    HDTV(1080i)

    50/60

    1920x1080

    1920x1080

    1920x1080

    1920x1200

    1920x1080

    1920x1080

    HDTV(1080p)

    50/60

    1920x1080

    1920x1080

    1920x1080

    1920x1200

    1920x1080

    1920x1080

    Composite Video/S-Video
    Units: dots
    Signal

    Refresh Rate (Hz)

    Resolution

    Aspect Mode
    Normal

    16:9

    Full

    Zoom

    Native

    TV(NTSC)

    60

    720x480

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    640x480

    TV(PAL,SECAM)

    50

    720x576

    1600x1200

    1920x1080

    1920x1200

    1920x1200

    768x576



  • Page 116

    Supported Monitor Displays

    116

    Input signal from the HDMI/DVI-D input port
    Units: dots
    Signal

    *

    Refresh Rate (Hz)

    Resolution

    Aspect Mode
    16:9

    Full

    Zoom

    Native

    VGA

    60

    640x480

    1920x1080

    1920x1200

    1920x1200

    640x480

    SVGA

    60

    800x600

    1920x1080

    1920x1200

    1920x1200

    800x600

    XGA

    60

    1024x768

    1920x1080

    1920x1200

    1920x1200

    1024x768

    WXGA

    60

    1280x800

    1920x1080

    1920x1200

    1920x1200

    1280x800

    SXGA

    60

    1280x960

    1920x1080

    1920x1200

    1920x1200

    1280x960

    60

    1280x1024

    1920x1080

    1920x1200

    1920x1200

    1280x1024

    SXGA+

    60

    1400x1050

    1920x1080

    1920x1200

    1920x1200

    1400x1050

    UXGA

    60

    1600x1200

    Non-compatible

    1920x1200

    1920x1200

    1600x1200

    WUXGA*

    60

    1920x1200

    1920x1080

    1920x1200

    1920x1200

    1920x1200

    SDTV(480i)

    60

    720x480

    1920x1080

    1920x1200

    1920x1200

    640x480

    SDTV(480p)

    60

    720x480

    1920x1080

    1920x1200

    1920x1200

    640x480

    SDTV(576i)

    50

    720x576

    1920x1080

    1920x1200

    1920x1200

    768x576

    SDTV(576p)

    50

    720x576

    1920x1080

    1920x1200

    1920x1200

    768x576

    HDTV(720p)

    50/60

    1280x720

    1920x1080

    1920x1200

    1920x1080

    1280x720

    HDTV(1080i)

    50/60

    1920x1080

    1920x1080

    1920x1200

    1920x1080

    1920x1080

    HDTV(1080p)

    24/30/50/60

    1920x1080

    1920x1080

    1920x1200

    1920x1080

    1920x1080

    Only compatible when VESA CVT-RB(Reduced Blanking) signal is input.



  • Page 117

    Supported Monitor Displays

    117

    Supported Monitor Displays for EB-Z8050W
    Computer signals (analog RGB)
    Units: dots
    Signal

    Refresh Rate (Hz)

    Resolution

    Aspect Mode
    Normal

    16:9

    Full

    Zoom

    Native

    VGAEGA

    70

    640x350

    1280x700

    1280x720

    1280x800

    1280x700

    640x350

    VGA

    60/72/75/85/iMac*1

    640x480

    1066x800

    1280x720

    1280x800

    1280x800

    640x480

    SVGA

    56/60/72/75/85/iMac*1

    800x600

    1066x800

    1280x720

    1280x800

    1280x800

    800x600

    XGA

    60/70/75/85/iMac*1

    1024x768

    1066x800

    1280x720

    1280x800

    1280x800

    1024x768

    WXGA

    60/75/85

    1280x768

    1280x768

    1280x720

    1280x800

    1280x768

    1280x768

    60

    1360x768

    1280x722

    1280x720

    1280x800

    1280x722

    1280x800

    60/75/85

    1280x800

    1280x800

    1280x720

    1280x800

    1280x800

    1280x800

    WXGA+

    60/75/85

    1440x900

    1280x800

    1280x720

    1280x800

    1280x800

    1280x800

    WSXGA+

    60

    1680x1050

    1280x800

    1280x720

    1280x800

    1280x800

    1280x800

    SXGA

    70/75/85

    1152x864

    1066x800

    1280x720

    1280x800

    1280x800

    1280x800

    60/75/85

    1280x1024

    1000x800

    1280x720

    1280x800

    1280x800

    1280x800

    60/75/85

    1280x960

    1066x800

    1280x720

    1280x800

    1280x800

    1280x800

    SXGA+

    60*2/75/85

    1400x1050

    1066x800

    1280x720

    1280x800

    1280x800

    1280x800

    UXGA

    60

    1600x1200

    1066x800

    1280x720

    1280x800

    1280x800

    1280x800

    WUXGA*3

    60

    1920x1200

    1280x800

    1280x720

    1280x800

    1280x800

    1280x800

    MAC13”

    67

    640x480

    1066x800

    1280x720

    1280x800

    1280x800

    640x480

    MAC16”

    75

    832x624

    1066x800

    1280x720

    1280x800

    1280x800

    832x624

    MAC19”

    75

    1024x768

    1066x800

    1280x720

    1280x800

    1280x800

    1024x768

    60

    1024x768

    1066x800

    1280x720

    1280x800

    1280x800

    1024x768



  • Page 118

    Supported Monitor Displays

    Signal
    MAC21”

    Refresh Rate (Hz)
    75

    118

    Resolution
    1152x870

    Aspect Mode
    Normal

    16:9

    Full

    Zoom

    Native

    1059x800

    1280x720

    1280x800

    1280x800

    1152x800

    *1 Connection is disabled if the equipment does not have a VGA output port.
    *2 Only compatible when Normal is selected as the Resolution from the configuration menu.
    *3 Only compatible when VESA CVT-RB(Reduced Blanking) signal is input.
    Even when signals other than those mentioned above are input, it is likely that the image can be projected. However, not all functions may be supported.

    Component Video
    Units: dots
    Signal

    Refresh Rate (Hz)

    Resolution

    Aspect Mode
    Normal

    16:9

    Full

    Zoom

    Native

    SDTV(480i)

    60

    720x480

    1066x800

    1280x720

    1280x800

    1280x800

    640x480

    SDTV(576i)

    50

    720x576

    1066x800

    1280x720

    1280x800

    1280x800

    768x576

    SDTV(480p)

    60

    720x480

    1066x800

    1280x720

    1280x800

    1280x800

    640x480

    SDTV(576p)

    50

    720x576

    1066x800

    1280x720

    1280x800

    1280x800

    768x576

    HDTV(720p)

    50/60

    1280x720

    1280x720

    1280x720

    1280x800

    1280x720

    1280x720

    HDTV(1080i)

    50/60

    1920x1080

    1280x720

    1280x720

    1280x800

    1280x720

    1280x800

    HDTV(1080p)

    50/60

    1920x1080

    1280x720

    1280x720

    1280x800

    1280x720

    1280x800

    Composite Video/S-Video
    Units: dots
    Signal

    Refresh Rate (Hz)

    Resolution

    Aspect Mode
    Normal

    16:9

    Full

    Zoom

    Native

    TV(NTSC)

    60

    720x480

    1066x800

    1280x720

    1280x800

    1280x800

    640x480

    TV(PAL,SECAM)

    50

    720x576

    1066x800

    1280x720

    1280x800

    1280x800

    768x576



  • Page 119

    Supported Monitor Displays

    119

    Input signal from the HDMI/DVI-D input port
    Units: dots
    Signal

    *

    Refresh Rate (Hz)

    Resolution

    Aspect Mode
    16:9

    Full

    Zoom

    Native

    VGA

    60

    640x480

    1280x720

    1280x800

    1280x800

    640x480

    SVGA

    60

    800x600

    1280x720

    1280x800

    1280x800

    800x600

    XGA

    60

    1024x768

    1280x720

    1280x800

    1280x800

    1024x768

    WXGA

    60

    1280x800

    1280x720

    1280x800

    1280x800

    1280x800

    SXGA

    60

    1280x960

    1280x720

    1280x800

    1280x800

    1280x800

    60

    1280x1024

    1280x720

    1280x800

    1280x800

    1280x800

    SXGA+

    60

    1400x1050

    1280x720

    1280x800

    1280x800

    1280x800

    UXGA

    60

    1600x1200

    1280x720

    1280x800

    1280x800

    1280x800

    WUXGA*

    60

    1920x1200

    1280x720

    1280x800

    1280x800

    1280x800

    SDTV(480i)

    60

    720x480

    1280x720

    1280x800

    1280x800

    640x480

    SDTV(480p)

    60

    720x480

    1280x720

    1280x800

    1280x800

    640x480

    SDTV(576i)

    50

    720x576

    1280x720

    1280x800

    1280x800

    768x576

    SDTV(576p)

    50

    720x576

    1280x720

    1280x800

    1280x800

    768x576

    HDTV(720p)

    50/60

    1280x720

    1280x720

    1280x800

    1280x720

    1280x720

    HDTV(1080i)

    50/60

    1920x1080

    1280x720

    1280x800

    1280x720

    1280x800

    HDTV(1080p)

    24/30/50/60

    1920x1080

    1280x720

    1280x800

    1280x720

    1280x800

    Only compatible when VESA CVT-RB(Reduced Blanking) signal is input.



  • Page 120

    Specifications

    120

    Projector General Specifications
    EB-Z8050W

    Product name

    534 (W) ^ 167 (H) ^ 734 (D) mm (not including raised section)

    Dimensions

    0.95" Wide

    Panel size

    1,024,000 pixels
    WXGA (1280 (W) ^ 800 (H) dots) ^ 3

    Resolution
    Focus adjustment
    Zoom adjustment *1
    Lens shift *1

    2,304,000 pixels
    WUXGA (1920 (W) ^ 1200 (H) dots) ^ 3
    Automatic
    Automatic (1-1.6)

    Automatic (Vertical direction: Maximum approx. 70%, Horizontal direction: Maximum approx. 20%)
    UHE lamp, 330 W Two-lamps Model No.: ELPLP52 (Two)/ELPLP51 (One)

    Lamp

    100-240V AC ±10%, 50/60Hz 10.7 to 4.5A

    Power supply
    100 to 120 V area

    Operating: 938W
    Standby power consumption (Communication On): 10.2W
    Standby power consumption (Communication Off): 0.3W

    Operating: 942W
    Standby power consumption (Communication On): 11.2W
    Standby power consumption (Communication Off): 0.3W

    200 to 240 V area

    Operating: 872W
    Standby power consumption (Communication On): 12.0W
    Standby power consumption (Communication Off): 0.5W

    Operating: 877W
    Standby power consumption (Communication On): 13.1W
    Standby power consumption (Communication Off): 0.5W

    Operating altitude
    Operating temperature
    Storage temperature
    Mass

    0.94" Wide
    Polysilicon TFT active matrix

    Display method

    Power consumption

    EB-Z8000WU

    Altitude 0 to 3048 m
    0 to 45˚C*2 (No condensation)
    -10 to +60˚C (No condensation)
    Approx. 22 kg

    *1 The specifications are when a standard lens is attached. When an optional lens is attached, check the User's Guide supplied with the optional lenses.
    *2 The operating temperature is 0 to +40˚C when "Power Consumption" is set to "Normal" at an altitude of 1500 to 3048m.



  • Page 121

    Specifications

    121

    Connectors
    Computer Input Port

    1

    Mini D-Sub15-pin (female) blue

    BNC Input Port

    1

    5BNC (female)

    HDMI Input Port *

    1

    HDMI HDCP compatible, CEC signal incompatible

    DVI-D Input Port *

    1

    DVI-D 24pin Single Link HDCP compatible

    Video input port

    1

    1BNC (female)

    S-Video input port

    1

    Mini DIN 4-pin

    Monitor Out port

    1

    Mini D-Sub15-pin (female) black

    LAN Port

    1

    RJ-45

    Wireless LAN Port

    1

    USB connector (Type A) only for the wireless LAN unit

    RS-232C Port

    1

    Mini D-Sub 9-pin (male)

    Remote port

    1

    Stereo mini jack

    *

    The projector can be connected to and project images from HDMI and DVI-D compatible equipment. However, images input from some equipment may not be
    projected.

    This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
    Pixelworks DNX

    ™ ICs are used in this projector.

    Angle of tilt

    Using the projector at angles not shown in the illustrations above may damage it or cause an accident.



  • Page 122

    Specifications

    122

    Operating Conditions for the Software
    The software supplied with the projector runs on computers that meet the following requirements.
    EasyMP Network Projection

    EasyMP Monitor

    OS

    Windows 2000 SP4/XP/XP SP1/XP SP2/XP SP3/Vista/Vista SP1
    Mac OS X 10.3 or later
    Recommended: Mac OS X 10.5.1 or later, 10.4.11/10.3.9

    Windows 98 Second Edition SP1/Windows Me/Windows NT4.0
    SP6/Windows 2000 Professional SP4/ Windows XP Home Edition
    SP2 or later/Windows XP Professional SP2 or later/Windows
    Vista (All editions except for Starter)/Windows Vista SP1 (All
    editions except for Starter)

    CPU

    Mobile Pentium III 1.2GHz or more
    Power PC G3 900MHz or more
    Recommended: Pentium M1.6GHz or more
    CoreDuo 1.5GHz or more

    Pentium MMX 166MHz or more
    Recommended: Pentium II 233MHz or more

    Amount of Memory

    256MB or more
    Recommended: 512MB or more

    64MB or more

    Hard Disk
    Free space

    20MB or more

    50MB or more

    Display

    Resolution greater than XGA (1024x768)
    Display color of approx. 32000 colors more than 16 bit colors

    Resolution greater than SVGA (800x600)
    Display color in 32 bit full-color or greater Display Color

    Internet Explorer Ver.5 or later must be installed.
    Administrator rights are required to use EasyMP Monitor when using the following operation systems.
    Windows 2000/Windows NT4.0/Windows XP/Windows Vista



  • Page 123

    Specifications

    123

    DECLARATION of CONFORMITY
    According to 47CFR, Part 2 and 15
    Class B Personal Computers and Peripherals; and/or
    CPU Boards and Power Supplies used with Class B
    Personal Computers
    We:
    Located at:

    Tel:

    Epson America, Inc.
    3840 Kilroy Airport Way
    MS: 3-13
    Long Beach, CA 90806
    562-290-5254

    Declare under sole responsibility that the product identified herein,
    complies with 47CFR Part 2 and 15 of the FCC rules as a Class B
    digital device. Each product marketed, is identical to the representative
    unit tested and found to be compliant with the standards. Records
    maintained continue to reflect the equipment being produced can be
    expected to be within the variation accepted, due to quantity production
    and testing on a statistical basis as required by 47CFR 2.909. Operation
    is subject to the following two conditions : (1) this device may not
    cause harmful interference, and (2) this device must accept any
    interference received, including interference that may cause undesired
    operation.
    Trade Name:

    EPSON

    Type of Product:

    LCD Projector

    Model:

    H265C/H266C

    FCC Compliance Statement
    For United States Users

    This equipment has been tested and found to comply with the limits
    for a Class B digital device, pursuant to Part 15 of the FCC Rules.
    These limits are designed to provide reasonable protection against
    harmful interference in a residential installation. This equipment
    generates, uses, and can radiate radio frequency energy and, if not
    installed and used in accordance with the instructions, may cause
    harmful interference to radio communications. However, there is no
    guarantee that interference will not occur in a particular installation. If
    this equipment does cause harmful interference to radio or television
    reception, which can be determined by turning the equipment off and
    on, the user is encouraged to try to correct the interference by one or
    more of the following measures.
    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that
    to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.
    WARNING

    The connection of a non-shielded equipment interface cable to this
    equipment will invalidate the FCC Certification or Declaration of this
    device and may cause interference levels which exceed the limits
    established by the FCC for this equipment. It is the responsibility of the
    user to obtain and use a shielded equipment interface cable with this
    device. If this equipment has more than one interface connector, do not
    leave cables connected to unused interfaces. Changes or modifications
    not expressly approved by the manufacturer could void the user's
    authority to operate the equipment.



  • Page 124

    Appearance

    124

    A Center of lens
    B Distance from center of lens to suspension bracket fixing point

    Units: mm



  • Page 125

    Glossary

    125

    This section explains easily terms that are used with the projector and difficult terms that are not explained in the text of this guide. For details, refer
    to other commercially available publications.
    AMX Device Discovery

    AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.
    Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).
    See the AMX Web site for more details.
    URL http://www.amx.com/

    Aspect Ratio

    The ratio between an image's length and its height. HDTV images have an aspect ratio of 16:9 and appear elongated. The aspect ratio for
    standard images is 4:3.

    (Aspect Ratio)

    Component Video

    A Video signal which has the luminance component and color component separated to provide better image quality.
    Refers to images that consist of three independent signals: Y (luminance signal), Pb and Pr (color difference signals).

    Composite video

    Video signals that have the video brightness signals and color signals mixed together. The type of signals commonly used by household video
    equipment (NTSC, PAL, and SECAM formats). The carrier signal Y (luminance signal) and chroma (color) signal that are contained in the color
    bar are overlapped to form a single signal.

    Contrast

    The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or
    to make them appear softer. Adjusting this particular property of an image is called Contrast adjustment.

    DHCP

    An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP Addressg to equipment connected to a
    Network.

    Dolby Digital

    A sound format developed by Dolby Laboratories. Normal stereo is a 2-channel format that uses two speakers. Dolby Digital is a 6- channel
    (5.1-channel) system which adds to this a center speaker, two rear speakers, and a sub-woofer.

    Gateway address

    This is a server (router) for communicating across a network (subnet) divided according to subnet masksg.

    (Gateway Address)

    HDCP

    HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by
    encrypting digital signals sent over DVI and HDMI ports. Digital images protected by HDCP technology can be projected with this projector
    because the projector's DVI-D and HDMI input ports are compatible with HDCP. However, the projector may not be able to project images
    protected with updated or revised versions of HDCP encryption.

    HDTV

    An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
    • Vertical resolution of 720p or 1080i or greater (p = Progressiveg, i = Interlaceg)
    • Screen Aspect Ratiog of 16:9
    • Dolby Digitalg audio reception and playback (or output)

    Interlace

    A method of image scanning whereby the image data is divided into fine horizontal lines that are displayed in sequence starting from left to right
    and then from top to bottom. The even-numbered lines and odd-numbered lines are displayed alternately.

    IP Address

    A number to identify a computer connected to a Network.



  • Page 126

    Glossary

    126

    Progressive

    A method of image scanning whereby the image data from a single image is scanned sequentially from top to bottom to create a single image.

    Refresh Rate

    The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image must be
    scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the Refresh Rate
    and is expressed in hertz (Hz).

    SDTV

    An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTVg
    High-Definition Television.

    SNMP

    An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and
    computers connected to a TCP/IP Network.

    sRGB

    An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by
    computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal
    source to sRGB.

    Subnet mask
    (Subnet Mask)

    This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP Addressg.

    SVGA

    A type of video signal with a resolution of 800 (horizontal) ^ 600 (vertical) dots that is used by IBM PC/AT-compatible computers.

    S-Video

    A Video signal which has the luminance component and color component separated to provide better image quality.
    Refers to images that consist of two independent signals: Y (luminance signal) and C (color signal).

    SXGA

    A type of video signal with a resolution of 1,280 (horizontal) ^ 1,024 (vertical) dots that is used by IBM PC/AT-compatible computers.

    Sync.

    The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are
    not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is
    called Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.

    Tracking

    The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are
    not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If Tracking is
    not carried out correctly, wide vertical stripes appear in the signal.

    Trap IP Address

    This is the IP Addressg for the destination computer used for error notification in SNMP.

    VGA

    A type of video signal with a resolution of 640 (horizontal) ^ 480 (vertical) dots that is used by IBM PC/AT-compatible computers.

    XGA

    A type of video signal with a resolution of 1,024 (horizontal) ^ 768 (vertical) dots that is used by IBM PC/AT-compatible computers.



  • Page 127

    General Notes
    All rights reserved. No part of this publication may be reproduced, stored in a
    retrieval system, or transmitted in any form or by any means, electronic, mechanical,
    photocopying, recording, or otherwise, without the prior written permission of Seiko
    Epson Corporation. No patent liability is assumed with respect to the use of the
    information contained herein. Neither is any liability assumed for damages resulting
    from the use of the information contained herein.
    Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of
    this product or third parties for damages, losses, costs, or expenses incurred by the
    purchaser or third parties as a result of: accident, misuse, or abuse of this product or
    unauthorized modifications, repairs, or alterations to this product, or (excluding the
    U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
    maintenance instructions.
    Seiko Epson Corporation shall not be liable against any damages or problems arising
    from the use of any options or any consumable products other than those designated
    as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

    127

    General Notice
    Windows Vista and the Windows logo are trademarks of the Microsoft Corporation
    and affiliated companies.
    IBM, DOS/V, and XGA are trademarks or registered trademarks of International
    Business Machines Corp.
    Macintosh, Mac, and iMac are registered trademarks of Apple Inc.
    Windows, WindowsNT, PowerPoint are trademarks or registered trademarks of
    Microsoft Corporation in the United States and other contries.
    Dolby is a trademark of Dolby Laboratories.
    Pixelworks and DNX are trademarks of Pixelworks Inc.
    PJLink trademark is a trademark applied for registration or is already registered in
    Japan, the United States of America and other countries and areas.
    Other product names used herein are also for identification purposes only and may
    be trademarks of their respective owners. Epson disclaims any and all rights in those
    marks.

    The contents of this guide may be changed or updated without further notice.
    Illustrations in this guide and the actual projector may differ.

    Wireless Telegraphy Act Regulations
    The following acts are prohibited by the Wireless Telegraphy Act.
    • Modifying and disassembling (including the antenna)
    • Removing the label of conformance
    • IEEE 802.11a (5 GHz band) external use

    ©SEIKO EPSON CORPORATION 2009. All rights reserved.



  • Page 128

    Index

    128

    t indicator .................................................... 71

    Cross .............................................................. 31
    Customized ................................................... 23

    H

    DHCP ............................................................ 52
    Direct Power On .......................................... 50
    Direction ....................................................... 50
    Display ........................................................... 49
    Display Background .................................... 49
    Distance ...................................................... 103
    DVI/HDMI Video Range ........................... 47
    DVI-D input port ........................................ 11
    Dynamic ........................................................ 23

    I

    ECO ............................................................... 48
    ESC/VP21 ................................................... 111
    Extended Menu ............................................ 49
    E-Zoom ......................................................... 31

    K

    Handle ..................................................... 10, 41
    HDMI input port ......................................... 11
    Help function ............................................... 70
    High Altitude Mode .................................... 50
    How to replace the air filter ........................ 92
    How to replace the lamp ............................. 89

    A
    Abs. Color Temp. ........................................ 44
    Address 1/2/3 settings ................................. 53
    Air Filter Notice ........................................... 50
    Air filter replacement period ..................... 92
    Air intake vent .............................................. 10
    Angle of tilt ................................................. 121
    Aspect ...................................................... 25, 47
    Auto Iris .................................................. 24, 45
    Auto Setup .................................................... 46

    D

    Image Menu ................................................. 44
    Indicators ...................................................... 71
    Info Menu ..................................................... 67
    Input Signal ............................................ 47, 67
    Interface cover ..................................... 10, 107
    IP Address ..................................................... 52

    B
    BNC input port ............................................ 11
    BNC Sync Termination .............................. 50
    Brightness ..................................................... 44

    E

    C
    Ceiling ........................................................... 49
    Ceiling mount fixing points ....................... 10
    Cinema Filter ................................................ 23
    Cleaning the Air filter ................................. 85
    Cleaning the Projector's Surface ................ 85
    Color Adjustment ........................................ 45
    Color Mode ............................................ 23, 44
    Color Saturation .......................................... 44
    Computer input port ................................... 11
    Configuration Menu ................................... 43
    Consumables ................................................ 95
    Contrast ........................................................ 44
    Control panel ............................................... 12
    Control Panel Lock ............................... 39, 48

    Keystone ........................................................ 48

    L

    F

    Lamp cover ................................................... 12
    Lamp Hours .................................................. 67
    Lamp replacement period .......................... 89
    Lamp1/2 indicator ....................................... 71
    LAN port .............................................. 11, 105
    Language ....................................................... 51
    Lens button ............................................. 12, 13
    Lens Operation Lock ................................... 40
    Lens Shift button .......................................... 14

    Filter indicator ............................................. 71
    Freeze ............................................................. 24
    Front .............................................................. 49
    Front adjustable foot ................................... 10
    Front cover ........................................... 10, 107
    Full Lock ....................................................... 39

    G
    Gateway Address ......................................... 52

    M
    MAC Address ............................................... 52



  • Page 129

    Index

    129

    Power inlet .................................................... 11
    Power On Protect ........................................ 37
    Presentation .................................................. 23
    Problem Solving ........................................... 71
    Progressive .................................................... 46
    Projection ...................................................... 49
    Projection lens .............................................. 10
    Projection lens unit ................................... 107
    Projector ID .................................................. 33
    Projector Name ...................................... 53, 56

    Mail ................................................................ 53
    Mail Notification ......................................... 53
    Menu Size ..................................................... 49
    Messages ....................................................... 49
    Monitor Displays ....................................... 114
    Monitor Out port ................................ 11, 106
    Multi-screen ................................................. 50

    N
    Network Menu ....................................... 51, 54
    Network Protect ........................................... 38
    Noise Reduction ........................................... 47
    Normal .......................................................... 48

    O

    Sharpness ...................................................... 44
    Shutter ........................................................... 24
    Shutter Timer ............................................... 50
    Signal Menu .................................................. 46
    Sleep Mode ................................................... 50
    SMTP Server ................................................. 53
    SNMP ............................................................ 52
    Software keyboard ....................................... 53
    Source ............................................................ 67
    Source Search ......................................... 12, 21
    Specifications ............................................. 120
    Sports ............................................................. 23
    sRGB .............................................................. 23
    Standby Mode .............................................. 50
    Startup Screen .............................................. 49
    Storage temperature .................................. 120
    Subnet Mask ................................................. 52
    Supported Monitor Displays .................... 114
    S-Video Input Port ...................................... 11
    Sync Info ....................................................... 67
    Sync. ............................................................... 46

    Q
    Quick Corner ......................................... 17, 48

    R
    Operating temperature ............................. 120
    Operation ...................................................... 50
    Optional accessories .................................... 94
    Overheating .................................................. 72

    Rear ................................................................ 49
    Rear screen .................................................... 84
    Refresh Rate .................................................. 67
    Remote Control ........................................... 13
    Remote Control ID ...................................... 34
    Remote port .................................................. 11
    Remote Receiver .......................................... 10
    Replacing batteries ....................................... 88
    Reset All ........................................................ 68
    Reset Menu ................................................... 68
    Resetting the lamp operating time ............ 91
    Resolution ..................................................... 67
    RS-232C port ....................................... 11, 111

    P
    Part Names and Functions ......................... 10
    Partial Lock ................................................... 39
    Password Protect ......................................... 37
    Password protect sticker ............................. 38
    Photo ............................................................. 23
    PJLink .......................................................... 113
    PJLink Password .......................................... 52
    Pointer ........................................................... 30
    Pointer Shape ............................................... 48
    Port Number ................................................ 53
    Position ......................................................... 46
    Power Consumption ................................... 48

    S

    T
    Temp indicator ............................................
    Test Pattern ..................................................
    Theatre ..........................................................
    Tint ................................................................
    Tracking ........................................................
    Trap IP Address 1/2 ....................................

    71
    49
    23
    44
    46
    52

    U
    Screen size ................................................... 103
    Security slot .................................................. 10
    Settings Menu ............................................... 48

    User's Logo ................................................... 97
    User's Logo Protect ...................................... 37



  • Page 130

    Index

    V
    Video input port .......................................... 11
    Video Signal ........................................... 47, 67

    W
    Web Control Password ............................... 52
    Wide-screen projection .............................. 25
    Wired LAN ................................................... 52

    Z
    Zoom ............................................................. 14

    130






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Epson EB Z8000WU wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Epson EB Z8000WU in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 5,24 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info