543654
77
Zoom out
Zoom in
Vorherige Seite
1/130
Nächste Seite
The message "Not supported" is displayed.
Check Remedy
Is the image signal format setting correct?
Only when projecting images from a video source
Change the setting according to the signal for the connected equipment. s Signal Menu - Video Signal p.46
Do the image signal Resolution and the Refresh Rate correspond
to the mode?
Only when projecting computer images
Refer to the computer's documentation for how to change the image signal Resolution and the Refresh Rate output
from the computer. s "Supported Monitor Displays" p.114
"No Signal" is displayed.
Check Remedy
Are the cables connected correctly? Check that all the cables required for projection are securely connected. s Quick Start Guide
Is the correct input port selected? Change the image by pressing the [Source Search] button on the Remote Control or the Control panel. s p.21
Is the power for the computer or video source turned on? Turn the power on for the equipment.
Are the image signals being output to the projector?
Only when projecting images from a laptop computer or a computer
with a built-in LCD screen
If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to
change the output to an external destination as well as the computer's own monitor. For some computer models,
when the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.
s
Computer's documentation, under a title such as "External output" or "Connecting an external monitor".
If the connection is made while the power of the projector or computer is already turned on, the function [Fn] key
that changes the computer's image signal to external output may not work. Turn the power for the computer and the
projector off and then back on again.
Images are fuzzy or out of focus
Check Remedy
Is the focus adjusted correctly? Press the [Focus] button on the remote control to adjust the focus. s Quick Start Guide
Is the projector at the correct distance? Is it projecting outside of the recommended projection distance range?
Setup within the recommended range. s p.103
Is the Keystone adjustment value too large? Lower the projection angle to reduce the amount of keystone correction. s Quick Start Guide
Problem Solving
77
77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Epson EB Z8000WU wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info