543654
81
Zoom out
Zoom in
Vorherige Seite
1/130
Nächste Seite
Other problems
The Remote Control does not work
Check Remedy
Is the remote control light-emitting area pointing towards the
remote receiver on the projector when it is operated?
Point the remote control towards the Remote Receiver.
Operating range s Quick Start Guide
Is the remote control too far from the projector? The operating range for the remote control is about 15 m. s Quick Start Guide
Is direct sunlight or strong light from fluorescent lamps shining
onto the Remote Receiver?
Set the projector up in a location where strong light does not shine onto the remote receiver. Or set the remote
receiver to Off from Remote Receiver in the configuration menu. s Settings Menu - Remote Receiver p.48
Is the correct setting for the remote receiver selected? Check the Remote Receiver from the configuration menu. s Settings Menu - Remote Receiver p.48
Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary. s p.88
Are the remote control ID and the projector ID matched? Make sure the ID for the projector you want to operate and the ID for the remote control match. To operate all
projectors by remote control regardless of the ID setting, set the ID switch on the side of the remote control to Off.
s p.32
Does Remote Control Type match the remote control that you
are using?
Check the Remote Control Type on the configuration menu. s Extended Menu - Operation - Remote Control
Type p.49
Is the optional remote control cable connected to the remote
control or to the projector's remote port?
When the remote control cable is connected, the remote control light-emitting area or the projector's remote
receiver are disabled. When not using the remote control cable set, disconnect it from the remote control and the
remote port.
Nothing appears on the external monitor
Check Remedy
Are images input from a port other than the Computer or
BNC input port?
The only images that can be displayed on an external monitor are computer images from the Computer
or BNC input ports. s p.106
I want to change the language for messages and menus
Check Remedy
Change the Language setting. Adjust the Language setting from the configuration menu. s Extended Menu - Language p.49
Problem Solving
81
81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Epson EB Z8000WU wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info