Bedienungsanleitung Espressions EP9650 Smart Kettle (Seite 5 von 9) (Englisch)

783509

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Using your Smart KettleEspressions Quiet Shield®

The Espressions Smart Kettle features the

Espressions Quiet Shield® which is new and

exclusive quietboil technology designed to make

boiling water a peaceful practice.

The Espressions Quiet Shield® is a stainless steel

disk attached to the kettle ﬂoor which acts as

a diffuser plate. It is perforated with a range of

holes which help disperse, and reduce the size of,

the water bubbles thus signiﬁcantly reducing the

noise of the boiling process.

Maintaining the Quiet Boil Technology.

Mineral deposits in tap water solidify when

the water is heated; lime scale may be white,

coloured, even rusty-looking and is normally

visible but phosphate scale isn’t generally visible

although may cause the water to appear cloudy

when heated.

Regular use of the kettle can lead to the build-up

of these minerals which reduces the effectiveness

of the Espressions Quiet Shield® as well as the

performance of the kettle.

It is important to descale your kettle regularly to

maintain the Quiet Shield® and to prolong the life

of the kettle.

Espressions recommend that the kettle is descaled

every 4-6 weeks. Go to page 10 for more

information on how to descale your Espressions

Smart Kettle.

Before using your kettle.

It is recommended that you clean your kettle

before using it by ﬁlling the kettle with water to

the maximum level indicator, boiling the water

and discarding.

Important: Do not ﬁll the kettle over the maximum

level, as water may spill out of the spout when

boiling.

1. To ﬁll the kettle, remove it from the power

base and lift the lid, by pressing the button at

the top of the handle.

2. Fill the kettle with the desired amount of water.

Always ﬁll the kettle between the minimum

and maximum marks. Do not ﬁll the kettle

below the ‘min’ indication because too little

water may result in the kettle switching off

before the water has boiled because of the boil

dry protection safety feature.

3. Push the lid closed ﬁrmly until it locks into

position.

4. Place the kettle onto the power base. Plug

the power cord into a 230-240 Volt AC power

outlet and switch the power on.

Note: If the kettle is not positioned on top of the

power base correctly the LCD panel will show

‘--:--°C’ and Current Temp before going into sleep

mode.

Using your Espressions Smart Kettle

Tip: The Espressions Smart Kettle has ﬁve

optimum tea temperatures you can select from:

80°C, 85°C, 90°C, 95°C and 100°C (Just Boil).

Refer to the ‘Tea Brewing Styles and Tips’ table

on page 11 for the ideal water temperature for

your tea.

Note: The temperature settings are a guide only

and may vary depending on personal preference.

1. All the buttons are one touch buttons. Select

the temperature you require by pressing the

speciﬁed button and the heating cycle will

activate immediately. The temperature button

you have selected will light up and all the other

buttons will not be illuminated.

If nothing has been selected after 30 seconds

the buttons will cease to be illuminated. After 10

minutes of nothing being selected the LCD screen

will go into sleep mode.

Note: During sleep mode the kettle consumes

less than 0.5W.

2. When the heating cycle is initiated, the LCD

display will show the estimated amount of

time required to reach the selected water

temperature. The Time to Boil feature shown

on the LCD display will count down until the

selected temperature is reached at which

point the kettle will beep. The kettle will

automatically turn off once temperature has

been reached.

3. During the heating cycle the LCD panel will

display the increasing temperature and the

number of minutes and seconds remaining

until the selected temperature is reached

4. The kettle will beep once when the selected

water temperature has been reached.

Note: To cancel the heating process at any time

during the boiling cycle, simply press the selected

temperature button once or remove the vessel

from the base.

Note: If the kettle is removed from the power

base during the heating process, the kettle will

automatically reset, cancelling the heating cycle.

40° / Sterilise feature

1. To select the 40°C feature press the button

once. The water is heated to 40°C.

Note: The ESTIMATED TIME to boil will not

be shown when 40°C is selected because it is

dependent on how much water is in the kettle

Note: To ensure the water temperature does not

exceed 40°C the heating process is purposely

intermittent and therefore it could take a few

minutes to get to this temperature

2. To select the Sterilise feature press and hold

the button for 1 second. The sterilisation feature

heats the water to 100°C and maintains a rolling

boil for 5 minutes. When the sterilisation

feature is activated the LCD screen will display

‘STERILISE CYCLE’.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Espressions EP9650 Smart Kettle Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Espressions EP9650 Smart Kettle

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info