Bedienungsanleitung Eudora BO 860 ALED (Seite 37 von 40) (Deutsch, Englisch)

499880

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

461307060 (RS-000)

15b

15a

INSTRUCTION FOR THE INSTALLER

TECHNICAL INFORMATION

All instructions related to installation and

maintenance operations listed in this section

must be carried out only by authorised

personnel.

The manufacturer cannot be held responsible

for any damage to persons or property resulting

from an incorrect installation of the appliance.

UNPACKING YOUR APPLIANCE

• Once the packaging has been removed, thoroughly

check that the appliance is in perfect condition. If

you have any doubts do not use the appliance and

call our Service Centre.

• Do not move the appliance by the handles.

• Some parts mounted on the appliance are protected

by a plastic ﬁ lm. This protection must be removed

before using the appliance. We recommend slitting

the plastic ﬁ lm along the edges with a sharp knife

or pin.

All packaging materials used (cardboard boxes,

bags, polystyrene foam, nails, etc.) must be

kept out of the reach of children, as they are a

potential hazard source. All packaging materials

used are environmentally-friendly and recyclable

(wooden bits are free from chemicals, cardboard

is 80-100% recycled, protective bags are made

in polyethylene (PE), bands in polypropylene

(PP) and padding in polystyrene foam (PS)

without chloro-ﬂ uoro-carbides. Waste materials

can undergo treatment and be recycled saving

on new raw materials and on the amount wasted

volumes. For this purpose we suggest you take

the packaging material back to the shop you

bought the appliance or to a collecting service.

Ask your local service for the nearest service.

WARNINGS

• As this is a built-in oven, please ascertain that

the walls or panels surrounding the appliance

can withstand a temperature of over 70 K.

• Also make sure that the glue that joins the

laminated plastic coat to the unit can withstand

a temperature of around 150°C, to avoid the

laminated coat to unglue.

INSTALLING AND FIXING THE OVEN

The oven can be housed into a cabinet or into a base

module, making room for its volumes as shown in ﬁ g. 14.

To guarantee proper aeration of the heat remove

the rear panel of the base module or make an

escape opening (A), as shown in ﬁ g. 14.

Fixing ovens with door horizontally hinged

• Fit the appliance in place.

• Open the oven door and secure the oven with the

screws supplied (V) (ﬁ g. 15a).

Fixing ovens with door vertically hinged

• With the oven door closed, unscrew the inferior

screw (ﬁ g.15b) with a hexagonal key n. 8 (not

supplied) and remove the door take off it from the

superior pivot.

• Fit the appliance in place and secure it with the

screws supplied (V) (ﬁ g. 15a).

• Reassemble the door inserting it in the superior

pivot and then, with the door closed, tighten the

inferior screw.

The oven must stand on a solid platform that

will withstand its full weight, as screws are only

used to secure the appliance inside its cabinet

housing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eudora BO 860 ALED Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info