Bedienungsanleitung EWT Lee de luxe (Seite 5 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Polnisch, Norwegisch, Finnisch)

706530

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Controls - see Fig. 2

O/I Switch

Main ON/OFF

Note: This switch must be pressed before the unit will operate

with or without heat.

- Switch

Flame Effect.

Note: This controls the ame effect option. This switch must be

pressed before the heater will operate with heat.

- Switch

Cold Blow Function.

Note: This switch must be pressed before the ‘Heat Selection’

switch operates.

- Switch

Heat Selection.

Provides 1 kW and 2 kW heat output thermostatically controlled.

Press button once for 1kW & twice for 2kW output. if button is

pressed a third time the heater reverts to ‘Cold Blow’ mode.

- Switch

Runback Timer.

The timer provides 15 individual time settings. Each time the

button is pressed the heater is programmed to run for 30

minutes,e.g. 1 press = 0.5hour, 2 presses = 1hour, etc.

This means the heater can be programmed to run for between

0.5 and 7.5 hours.

Thermostat (T) - see Fig.2

In order to maintain a certian room temperature, set the controller

to ‘max’. Operate the heater at full power until the required room

temperature ie reached. Turn back the thermostat control knob

until the heater turns off with an audiable ‘click’. This temperture

will be kept almost constant by the thermostatic control switching

ON and OFF automatically. Please note that the appliance can

only be switched ON when the thermostat setting is higher than

the room temperature.

Flame Control Knob (F) - see Fig.2

By using the ame control knob, the brightness of the ame effect

can be adjusted. At min. setting (indicated by the small bulb) the

brigthness of the ame effect will be lowest. Clockwise rotation

of the knob will increase the intensity of the ame effect.

LED Indicators - see Fig.6

Red LED’s (Neons) will be visable on the right side of the heater

glass window indicating the selected funstion.

For Example when 1kW heat is selected, you will wee the ON/

OFF - LED and the 1kW LED illuminated, or for another example,

if the run back timer is set to6.5 hours the rst, second and the

fourth LED of the timer indicators will be illuminated (4 hours +

2 hours = 0.5 hours = 6.5 hours)

}

2 kW heat

1 kW heat

Cold Blow Function

On/Off

4 hours

2 hours

0.5 hour

1 hour

Timer Indicators only

Remote control - see Fig. 7

The maximum range of use is ~ 10metres/32.8 ft.

The buttons on the remote control have the same functions as

the switches on the heater.

For detailson the funstions please refer to the ‘Controls’ section

in this leaet.

Warning: It takes time for the receiver to respond to the

transmitter.

Do not press the buttons more than once within two seconds

for correct operation.

Battery Information - see Fig. 7

1. Slide open the battery cover on the back of the remote control.

2. Install two AAA batteries into the remote control, being careful

to insert the battery as indicated in the battery compartment of

the handset.

3. Replace the battery cover.

Discard Leaking Batteries

Dispose of batteries in the proper manner according to provincial

and local regulations.

Any battery may leak electrolyte

- if mixed with a different battery type,

- if inserted incorrectly,

- if all the batteries are not replaced at the same time,

- if disposed of in a re,

- if an attempt is made to charge a battery not intended to be

recharged.

Disposal of Used Batteries.

Batteries may contain hazardous substances which could be

endangering to the environment and human health.

The symbol marked on the battery and /or packaging indicates

that used batteries should not be treated as municipal waste.

Instead they should be left at the appropriate collection point

for recycling.

By ensuring used batteries are disposed of correctly, you will help

to prevent potential negative consequences on the environment

and human health. The recycling of materials will help to conserve

natural resources.

For more information please contact your local authority.

Thermal Safety Cut-out

The built-in overheat cut-out switches off the appliance

automatically in the event of a fault! Switch off the appliance or

disconnect the mains plug from the socket.

Remove any obstructions which may have caused the

overheating. After a short cooling down phase, the appliance

is ready for use again! If the fault should occur again, see your

local dealer!

WARNING: In order to avoid a hazard due to inadvertent

resetting of the thermal cut-out, this appliance must not be

supplied through an external switching device, such as a timer,

or connected to a circuit that is regularly switched on and off by

the utility.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EWT Lee de luxe Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info