Bedienungsanleitung Exakt SP-180 (Seite 3 von 20) (Deutsch, Englisch, Französisch)

665047

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

2  Precision Tools Ltd. 2010

Safety Warnings – Operating

Instructions

The Planer / Sander is designed to be used either as a

conventional hand held powered planer, or as a hand held

powered drum sander. These instructions give details on how

to set the tool for both functions.

As with all power tools this tool is powered by electricity, has

exposed rotating parts, makes noise and creates dust. To

ensure personal safety and the safety of others it is essential

that the user reads and fully understands these instructions

and then considers and assesses the dangers carefully before

use. If the user does not fully understand how to use the tool,

or does not feel confident, they should seek instruction from a

suitably trained professional before use.

WARNING ! Wait for the cutter to stop before setting

the tool down. An exposed cuttermay engage the surface

leading to possible loss of control and serious injury. Use the

workstand provided.

Setting the Sanding Cutting Depth

The sanding depth can be set to anywhere up to a maximum

indicated setting (approx. 0.5mm). When using the tool as a

sander it is not recommended to set the depth greater than the

maximum indication on the top of the sander depth scale. For

a high quality finish using less effort, make several shallow

passes. Use a lower cutting depth when working with harder

materials.

a) Identify the sanding depth scale (See Illustrated

Description of Functions)

b) Turn the depth adjuster knob fully anticlockwise until

the arrow lines up with indicator pointer

c) Turn the knob clockwise until the required depth is

achieved

WARNING! In sanding mode the drum will always

remain slightly proud of the base plate even when the arrow

indicates a minimum setting.

Changing Sanding tubes

Sanding tubes are supplied (depending on kit) with varying

grit finishes. These can be changed depending on the

amount of sanding to be carried out & level of surface finish

required. Tubes can be changed by following the

procedure.

a) Unplug the tool from the electricity supply.

b) Remove the end cap screws using the Torx key

provided

c) Pull end cap away from side of machine to expose

the tube

d) Using the small spanner to hold the shaft, place the C

spanner into the slots and release (Diagram A)

e) Remove the locking nut and tube assembly

f) Remove the drum end cap which should come away

from the assembly without resistance

g) Remove the drive end cap by pushing it through the

middle of the sanding tube. This part is held in-situ by

a rubber grip ring (Diagram B)

h) Replace with another tube and re-assemble

List of contents

 1 x Planing / Sander

 1 x Fence guide

 2 x Keys

 1 x Vacuum adapter

 1 x Removal tool

 1 x Dust bag

 Spare sanding tubes

(dependant on kit)

 1 x Blade setting gauge

 1 x Ear plugs

 1 x Instruction manual

 1 x Case

 2 x Spanners

 1 x Dust mask

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Exakt SP-180 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info