695964
37
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
37ENGLISH
Displays
upDate Reason
OFF
Generator o
START
The START phase is in progress
PELLET LOADING
Continuous pellet feeding is in progress during the ignition state
IGNITION
The phase dedicated to ignition is in progress
PREPARATION
The ame stabilisation phase is in progress
WORK
The generator has reached operating capacity and is working on user settings
MODULATION
The generator is working at minimum capacity
FINAL CLEANING
The cleaning cycle is in progress which is required to cool the machine before it is switched o
STAND-BY
Generator o but in stand-by to reignite autonomously if required by operating requests
COOLING STAND BY
The generator is requested to turn on during the shut-down phase. If activated, the generator will automatically
turn on again as soon as safety conditions permit it to do so
BLACK OUT
STAND BY
The generator is cooling after a power cut. Once cooling is completed, it will re-start automatically
AUTO BLOW
The auto blow is in progress to keep the burn pot
clean and maximise combustion eciency
EMPTY HOPPER
The pellet hopper is empty.
Check for the presence of pellets in the hopper.
Contact the after-sales centre.
CLOSE
HOPPER-STOVE
DOOR
This indication means that you have 60 seconds to close the hatch/door and the pellet lid.
After 60 seconds have passed, the stove will enter DEPR ALARM during the ignition phase while during
normal operation, the stove will enter COOLING STAND BY and then, restart automatically when the conditions
are right (clod stove, etc.).
alaRMs
upDate eXplanation solution
FUMES MOTOR
FAULT
Fumes motor fault Contact the after-sales centre
FUMES PROBE
Fumes probe fault Contact the after-sales centre
HOT FUMES
High fumes temperature
Check the pellet ow (see “Pellet load adjustment”). If the problem
is not solve, contact a qualied technician
NO
IGNITION
The pellet hopper is empty
Pellet feed calibration inadequate
Make sure there are pellets in the hopper.
Adjust the pellet ow (see “Pellet load adjustment”).
Check the procedures described in the “Ignition chapter.
NO
IGNITION
BLACK OUT
No current during the ignition phase
Take the stove to o conditions using key 1 and repeat the
procedure described in the "Ignition" chapter.
NO FLAME
The pellet hopper is empty
No pellet load
The auger motor is not loading the pellets
Make sure there are pellets in the hopper.
Adjust the pellet ow (see “Pellet feed adjustment”).
DEPR ALARM
The door is not closed correctly
The combustion chamber is dirty
The fumes exhaust pipe is blocked/dirty
Check hermetic door closure.
Check cleanliness of the fumes pipe and the combustion chamber.
AUGER CONTROL
ALARM
Abnormal pellet loading Contact after-sales centre
37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Extraflame INSERTO COMFORT P85 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Extraflame INSERTO COMFORT P85

Extraflame INSERTO COMFORT P85 Bedienungsanleitung - Deutsch - 40 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info