Bedienungsanleitung Faber Agio 30BK (Seite 7 von 13) (Englisch, Französisch)

752945

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Version 7/11 - Page 7

Three Screws

Rangehood Body

Front

Strip

CUSTOMIZING YOUR RANGEHOOD

The front strip of the rangehood can be customized. The

front strip is attached to the rangehood by three recessed

screws and three key hole slots on the back side of the strip

as indicated in FIGURE 15. It is necessary only to remove

the three lower screws to remove the front strip. The top

screws will slide out of the key holes once the three lower

screws are removed.



The front strip dimensions are given in FIGURE 16. If you

wish to keep the frame of the front panel and only replace the

glass panel, the dimensions follow: Height = 5 11/16", Depth

= 1/8", Width = 29 11/16" (for 30" model) 35 11/16" (for 36"

model) 23 5/8" (for 24" model).

FIGURE 16

WIRING DIAGRAM

• This rangehood uses Flourescent Lamp Type 18", 15W T8 and

Starter Type S2.

Rangehood Control Panel

All controls are located under the front panel and are shown in

FIGURE 17.



On/Off switch for the uorescent light. Moving the switch to the

1 Position turns the light On. Moving the switch to the 0 Position

turns the light Off.

FIGURE 15

FIGURE 17

FIGURE 18



Controls blower speed. Moving the switch to the 1 Position turns

the blower on LOW. Moving the switch to the 2 Position turns the

blower on MEDIUM. Moving the switch to the 3 Position turns the

blower on HIGH.



Red light will be on when the rangehood is operating.



When the front panel of the rangehood is closed, the rangehood

will turn off by a microswitch. This turns the rangehood On and

Off without adjusting the switches for the Light or Blower and it

remembers the last speed setting.

Cleaning

The metal grease lters should be cleaned frequently in hot deter-

gent solution or placed in the dishwasher. Clean exterior surfaces

with hot soapy water. Using abrasives and scouring agents can

scratch rangehood nishes and should not be used to clean nished

surfaces.

Replacing the Fluorescent Light

To replace the uorescent light, remove the retainer clips from both

ends of the glass diffuser as indicated in FIGURE 18. Carefully

slide the glass diffuser all the way to the left. Lower the right end

of the glass below the support ange, then remove the glass by

sliding it back to the left. Replace the diffuser glass by reversing

these directions.

23 5/8" or 29 15/16" or 35 15/16"

5 7/8"

13/16"

USE AND CARE INFORMATION

This rangehood system is designed to remove smoke, cooking

vapors and odors from the cooktop area.

For Best Results

Start the rangehood several minutes before cooking to develop proper

airow. Allow the unit to operate for several minutes after cooking

is complete to clear all smoke and odors from the kitchen.

Blower On/Off



On/Off switch for the

blower. Moving the

switch to the 1 Posi-

tion turns the blower

On. Moving the switch

to the 0 Position turns

the blower Off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Agio 30BK Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info