Bedienungsanleitung Fagor 3CFT-TILE (Seite 4 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

108594

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Mounting

Before beginning installation:

• Check that the product purchased is of a suitable size for

the chosen installation area.

• To facilitate installation, remove the fat filters and the

other parts allowed and described here, dismantle and

mount it.

To remove see also the relative paragraphs.

• Remove the active carbon (*) filter/s if supplied (see also

relative paragraph). This/these is/are to be mounted only

if you want lo use the hood in the filtering version.

• Check (for transport reasons) that there is no other

supplied material inside the hood (e.g. packets with

screws (*), guarantees (*), etc.), eventually removing

them and keeping them.

• If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall/ceiling. Otherwise put a thick, protective

covering over countertop, cooktop or range to protect

from damage and debris. Select a flat surface for

assembling the unit. Cover that surface with a protective

covering and place all canopy hood parts and hardware

in it.

• Disconnect the hood during electrical connection, by

turning the home mains switch off.

• In addition check whether near the installation area of the

hood (in the area accessible also with the hood mounted)

an electric socket is available and it is possible to

connect a fumes discharge device to the outside (only

suction version).

• Carry out all the masonry work necessary (e.g.

installation of an electric socket and/or a hole for the

passage of the discharge tube).

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

In the case of the presence of panels and/or walls and/or

lateral wall units check that there is sufficient space to install

the hood and that access to the command panel is easy.

Fig. 5

• Trace a central line on the wall in order to ease mounting

(1), position the hole template in a way that the middle

line printed on top corresponds to the central line marked

previously and the lower side of the mask corresponds to

the lower part of the hood once mounted. (2).

• Make 3 holes Ø 8 mm with a drill and fix the support

bracket with two dowels and screws to the wall (3), insert

the third dowel into the lower hole.

• Open the vapour scheme and remove the grease filters

(see relevant paragraph).

• Hang the hood (4), regulate the position (5-6) and fasten

it securely with one screw and washer(7).

• Carry out electrical connections (8), but leave the hood

disconnected from the general electrical main panel.

• Install the grille/deflector F (9).

• Mount the grease filters and close the vapour scheme.

Warning! Make sure that the carbon filter is already

mounted on the back of the grease filter, or in case it’s

missing, buy it and install it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fagor 3CFT-TILE Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info