646345
22
Zoom out
Zoom in
Vorherige Seite
1/23
Nächste Seite
SELF DIAGNOSTIC FAULT CODES
The FEB-20E has a built in self diagnostic fault finding system incorporated into the P.C.B. Should a fault
develop on the boiler which could cause a situation liable for the operation of the boiler to become unsafe, then
the boiler will fail safe by locking-out which is displayed via the 'red neon' on the control panel.
The fault can be identified by the different sequences in which the 'red neon' flashes and the duration that the
neon stays illuminated. The electronic fail safe is also backed by a mechanical means of protection, should the
electronics fail to detect a fault. These mechanical forms of protection will protect and ensure the safe shut down
of the boiler.
The software protection built into the P.C.B. will run a system check on components which are essential to the
safe operation of the boiler. This occurs before any ignition sequence takes place. If any component is found to
be faulty or out of a predetermined range, then lock-out will be displayed.
Each fault code begins and finishes with the 'red neon' illuminated for 5 seconds, the relevant fault is then
indicated by the number of 1 second flashes which occur between the initial 5 second flash and the closing 5
second flash. These range from 0 - 12. Please be patient when counting the sequence as the correct identification
of the fault will save time on isolating and rectifying the problem.
Eg: Fault 6 water overheating would display the following sequence of the red neon;
5 seconds 1 sec 1 sec 1 sec 1 sec 1 sec 1 sec 5 seconds
N.B. The sequence repeats until either the reset button is depressed or the fault rectified. Some faults require the
component temperature to return within operating range before reset, is possible also some sequences may take
up to 3 minutes before lock-out is displayed, e.g. air pressure switch failure fault 1 or water over heating fault 6.
FAULT CODES FAULT
Lack of gas or ignition problems
Minimum burner pressure set to low
Flame supervision failure
0 Repeating 5 second flashes
With no 1 second flashes
Burner on but flame indicator off
1 One 1 second flash Air pressure switch failure, crossed tubes or flue venturi blocked
3 Three 1 second flashes Low central heating pressure or Hi-limit stat failure
4 Four 1 second flashes Printed circuit board failure
5 Five 1 second flashes Flame supervision failure, indicator light on burner off
6 Six 1 second flashes Water overheating
7 Seven 1 second flashes Control panel failure
9 Nine 1 second flashes Gas valve control circuit failure
10 Ten 1 second flashes Domestic hot water thermistor failure
12 Twelve 1 second flashes Central heating thermistor failure
These fault codes are for the new type PCB with the part number MU0870700, this can be
found on the bottom right hand corner of the board. You can also easily identify this PCB
which has two blue transformers attached.
This is a direct replacement for the older PCB with the part number MU0868700, this can be
found on the bottom centre of the board.
Note: Fan wire will need threading down from the fan to allow the plug to reach the
repositioned J10 terminal.
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

fagor-feb-20e-uk-ecoplus

Suche zurücksetzen

  • Warum geht Brenner nach 1 Std Laufzeit immer aus. Eingereicht am 19-5-2021 08:47

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fagor FEB-20E UK ECOPLUS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info