Bedienungsanleitung Fakir BOSS (Seite 10 von 12) (Englisch, Türkisch)

566107

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Before using the hair clipper:

The hair to be cut should be clean and dry or

damp. Carefully comb the hair to remove any

knots. Place a towel around the neck to prevent

any trimmed hair failing down inside the collar.

To prevent the electric shock, never use the

appliance near water/liquids when it is connected

to the mains supply.

Adjusting the cutting comb length:

You could cut your hair in 14 different lengths

with adjustable cutting combs. Please place the

adjustable cutting comb to the appliance. With

small cutting comb you could cut your hair

between 2mm-20mm and with large cutting comb

you could cut your hair between 22mm-40mm.

You could easily adjust the cutting comb length

with rotate switch on your appliance. By pulling

the rotate switch to upwards will rise the cutting

comb. There is an indicator left side of the

appliance that shows the cutting comb length.

You could find a table as below that shows hair

lengths equal to the cutting comb position.

NOTE: Hair thinner mechanism defines hair

style without changing the length of adjustable

cutting comb. By sliding the blade length control

switch, Titanium blades will rise. Rising Titanium

blades will provide hair to be cut easily and

provide best cutting performance of your

appliance.

Instructions for Hair Cutting:

NOTE:

If you are cutting for the first time, start

with the maxi-mum comb length (40mm).

Nape of the neck (Diagram A): Set the comb

position between 3mm and 6mm.Hold the clipper

with the blade teeth pointing upwards. Begin

starting at the centre of the head at the base of

the neck. Slowly lift the clipper, working upwards

and outwards through the hair, trimming just a

little at a time.

Back of the head (Diagram B): Set the comb

position at 12mm or 17mm, cut the hair at the

back of the head.

Side of the head (Diagram C): Set the comb

position between 3mm and 6mm, trim sideburns.

Then change to the longer setting (12 or 17mm)

and continue to cut to the top of the head.

Top of the head (Diagram D): Set the comb

position between 17mm and 22mm cut hair on

top of the head against the direction in which

the hair normally grows. To make longer hair on

top, use the appliance without comb attachment.

Lift the hair on top of the head with a small hand

comb. Cut over the hand comb with the hair

lifted or hold the hair between the fingers to lift

it and cut it to the desired length. Always work

from the back of the head.

The finishing touches (Diagrams E, F & G ): Use

the clipper without an attachment comb for close

trimming around the base and sides of the neck.

To produce a clean straight line at the sideburns,

reverse the hair clipper. Place the reversed

clipper at right angles to the head, tips of the

blades lightly touching the skin and then work

downwards.

Comb

position

Small cutting

comb

2 mm

5 mm

8 mm

11 mm

14 mm

17 mm

20 mm

Large cutting

comb

22 mm

25 mm

28 mm

31 mm

34 mm

37 mm

40 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fakir BOSS Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info