723661
2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Installation of Solid State Drive
1. Put the enclosure on a suitable mounting surface with the
LED-Opening pointing downward and the USB-Port to the
right.
2. If possible use a magnetic screwdriver. Loosen the screws on
the side of the USB-Port and remove the cover.
3. Hold the enclosure slightly at an angle and let the circuit
board slide out carefully.
4. If needed put the threaded piece into one of the recesses of
the circuit board to adapt to smaller SSD-formats.
5. Align the edge connector of your SSD on the socket and put it
in. The memorycard should now be angled upwards.
6. Press down the SSD and mount it on the back with the silver
screw.
Formatting the Solid State Drive
1. Right-Click on This PC” icon and select the “Manage column.
2. Select “Disk Management and you will see your SSD showed
“Not initialised” and “Unallocated”.
3. Right-Click on the red Symbol and select “Initialise Disk”.
4. Select “GPT mode. Then press OK button fi nish the initialising
procedure.
5. Right-Click on the “Unallocated” block and select “New Simple
Volume. Then follow up the dialogue box with pressing the
“Next” button until the “Finish” button will start the format-
ting procedure.
6. When formatting is completed, the external SSD will be recog-
nized as a “New Volume”.
7. Make sure that the enclosure is lieing the right way around
by looking at the L-shaped rails and the blue thermalpad on
the inside. Make sure the mounting screw is pointing upwards
and slide the circuit board in with the side with the screw fi rst
until it touches the opposite side. Be sure to have the rails
keep away the circuit board from the thermal pad.
8. Attach the cover with both screws until it sits fl ush.
9. Attention: If the data media is not recognized by your opera-
ting system after installation, it has to be formatted. Note that
in the process all data will be erased and create a backup if
need be.
Removal
1. Loosen the screws on the side of the USB-Port and remove the
cover.
2. Push the circuit board out of the rails so it loosens from the
thermalpad.
Attention: Do not try to remove the thermalpad and avoid
damaging it with the cicuit board or tools.
3. Now the cicuit board can be removed from the enclosure.
Fantec NVMe31
SSD-Memory-Enclosure
Installation Manual
Delivery
External enclosure
1× SSD-mounting-screw
1× Threaded piece for small SSD-Formats
Schraubendreher
Cable USB 3.1 Typ-C to Typ-C
Installation manual
Description
This enclosure supports the installation of a M.2 PCIe NVMe (Key
M or Key M+B) SSD in 2280, 2260 and 2242 format. The connec-
tion to a computer works via USB 3.1.
M.2 AHCI SSDs are not supported.
System Requirements
Windows 7/8.1/10 (32 or 64 bit)
Mac OS 10.14.3 or higher
USB Typ-C-port
Safety Instructions
Protect the product against moisture and direct sunlight
Avoid static discharge during installation
Adress for RMA Sending from Germany
For RMA-Service outside of Germany please contact your dealer!
Fantec GmbH
Department RMA/Service
Billwerder Billdeich 605 B
21033 Hamburg
service@fantec.de
www.fantec.de
Declaration of Conformity
www.fantec.de/unternehmen/bestimmungenrichtlinien/ce
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fantec NVMe31 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info