723651
12
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
21
22
1. Changing the RAID mode will cause data lost.
2. Please refer to the instructions when switching the RAID mode, otherwise the execution
might fail.
3. Interface of USB / eSATA can not be used at the same time.
4. When using RAID function, HDDs with the same brand, model and capacity is strongly
recommended.
5. When using RAID function, more than one HDD partition is not recommended.
6. Under Windows Vista / 7, users can enable GPT when initializing HDD with a total capacity
of more than 2TB.
7. Older OS may not recognize the device if you use a different operation system than
Windows Vista / 7. For more detailed information about GTP, please visit:
http://www.microsoft.com/whdc/device/storage/GPT FAQ.mspx
8. If users enable MBR by mistake, in order to clean the partition table, you have to switch to
another RAID mode and do the RAID mode switch all over again referring to Setup.
Then go back to the RAID mode you want, repeat the previous actions and enable
GPT when initializing HDD.
9. For Macintosh users: the total capacity of more than 2TB could be recognized only for the
operation system is 10.4.11 Tiger or later.
10. Do not connect the device to the SATA port on the motherboard.
Use SATA to eSATA PCI-Express or SATA to eSATA PCI add-on card, otherwise the
PC (Windows / Macintosh) may not recognize the device.
11. Rebuild time is based on the capacity, e.g. it takes about 1 hour for 200GB.
12. When the USB / eSATA cable is plugged out, the device goes to sleeping mode
automatically.
REFERENCES
Figure-1
14. If the noise is still present, you can change the fan with another identical fan
of size 80x80x20mm referring to Figure-1.
13. If there is noise with the fan, power off the device, unscrew the fan, take out the cover ,
clean the fan and assemble it back.
Black cableRed cable
Positive
(electrode)
Negative
(electrode)
15. Setting up motherboard's power management in S3 is recommended.
(For more details, please refer to the user guide of motherboard BIOS setting).
16. If the device takes too long to initialize, please check if the HDD is securely installed or
update the eSATA host driver version.
17. If the transfer rate is not normal, please check if the setting of SATA disk jumper
is 1.5 or 3.0Gbps .
18. If the fan stops working, turn off the unit and replace the fan.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fantec QB-X8US3R wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Fantec QB-X8US3R

Fantec QB-X8US3R Bedienungsanleitung - Deutsch - 13 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info