Bedienungsanleitung Fein asse 636 (Seite 16 von 113) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387996

Zoom out

Zoom in

Vorherige Seite

1/113

Nächste Seite

For your safety.

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the power tool:

Hand-held screwdriver for screwing in and unscrewing

screws and nuts in weather-protected environments

without water supply using the application tools and

accessories recommended by FEIN.

Special safety instructions.

Hold power tool by insulated gripping surfaces, when

performing an operation where the fastener may contact

hidden wiring or its own cord. Fasteners contacting a

“live” wire may make exposed metal parts of the power

tool “live”" and could give the operator an electric shock.

Beware of any concealed electric cables, gas or water

conduits; check the working area with a metal detector,

for example, before commencing work.

Secure the workpiece firmly. A work piece that is gripped

tightly in a clamping device or vice, is more secure than if

held by hand.

Hold the power tool firmly. High reaction torque can

briefly occur.

Do not machine any material containing asbestos. Asbes-

tos is cancerogenic.

Do not rivet or screw any name-plates or signs onto the

power tool. If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive

labels are recommended.

Do not use accessories which are not specifically

designed and recommended by the power tool manufac-

turer. Safe operation is not ensured merely because an

accessory fits your power tool.

Clean the ventilation openings on the power tool at regu-

lar intervals using non-metal tools. The blower of the

motor draws dust into the housing. An excessive accu-

mulation of metallic dust can cause an electrical hazard.

Before putting into operation, check the mains connec-

tion and the mains plug for damage.

Recommendation: The tool should always be supplied

with power via a residual current device (RCD) with a

rated current of 30 mA or less.

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Operating instructions.

Adjust the Rotation selector switch only when the

machine is at a complete stop.

For reliable working results, always carry out screwdriv-

ing operations using the depth stop.

SCU7-9: Use the auxiliary handle when working with the

torque level “Fix” (rigid through-drive), as torques in

excess of 28 Nm can develop. Do not use the depth stop.

Setting the torque (see page 6 –7)

The factory setting is for the small to mid-size screw

range.

The tightening torque also depends on the force with

which the power tool is pressed against the screw.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power tool.

The total insulation of the power tool can be impaired.

Blow out the interior of the power tool via the ventila-

tion slots frequently with dry and oil-free compressed air,

and connect a residual current device (RCD) on the line

side.

m/s

Vibrational emission value according to EN 60745

(vector sum of three directions)

m/s

Vibrational emission value (screwdriving)

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

Basic and derived units of measure from the inter-

national system of units SI.

Character Unit of measure,

international

Unit of measure,

national

Explanation

WARNING

OBJ_BUCH-0000000030-001.book Page 16 Tuesday, April 19, 2011 1:13 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein asse 636 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info