Bedienungsanleitung Felisatti BSF100 (Seite 4 von 29) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

502505

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Follow very carefully the instructions in this manual, save it

and keep it close at hand, ready to carry out any inspection

of parts that may be necessary.

If the machine is used carefully and normal maintenance is

carried out, it will work well for a long time.

The functions and use of the tool you have bought shall be

only those described in this manual. Any other use of the tool

is strictly forbidden.

ILLUSTRATIONS

DESCRIPTION (See gures)

A Lever (Fig.1 & 3)

B Steel plate (Fig.2)

C Adjustment screw (Fig.2)

D Sawdust extraction tube (Fig.2)

E Dust bag (Fig.3)

F Zip fastener (Fig.3)

G Blocking button (Fig.2)

H Trigger switch (Fig.1 & 2)

I Speed control (electronic model only) (Fig.2)

J Brush holder cover (Fig.3)

K Belt direction indicator arrow (Fig.2)

EQUIPMENT

- 1 sawdust and shaving collector bag

- 1 sanding belt (610x100) 80 grit

- Operating instructions

- Safety instructions

- Warranty

BRIEF DESCRIPTION

Any use differing from the above is strictly forbidden. Belt

sanders are devices equipped with powerful motors and an

“endless” abrasive belt, which rotates at great speed over two

rollers. These tools are perfectly adapted for grinding large

amounts of material in a short time: for instance, they are

ideal for rough-grinding wood, for rough sanding, for stripping

painted wood... However, they are not at all suitable for

achieving a ne nish.

BEFORE USING THIS TOOL

Before using the tool, make sure the mains voltage is correct:

it must be the same as that on the specication label.

Machines with 230V can also be connected to a 220-V mains

TECHNICAL DATA

supply.

Before plugging in the tool, always make sure that the trigger

switch works properly and returns to the “OFF” position when

released.

FITTING AND REMOVAL OF THE ABRASIVE BELT

WARNING! Always make sure that the tool is switched off

and unplugged before tting or removing the belt.

Follow the steps below:

1. Pull out lever A completely and t the belt over the rollers.

2. Make sure that the arrow on the back of the belt points in

the same direction as indicator arrow K on the tool.

3. Once the belt is tted over the rollers, push lever A back to

its original position.

4. Adjust the belt tracking: switch on the tool and make sure

the belt is properly aligned.

5. If the edge of the belt sticks out beyond the edge of the

steel plate B or is more than 6 mm from its inside edge, adjust

the belt tracking with the adjuster screw C.

DUST EXTRACTION

WARNING! Always make sure that the tool is switched off

and unplugged before tting or removing the dust bag.

The dust (sawdust) produced while sanding is extracted

into a sawdust collector bag. To t the bag, follow the steps

below:

1. Fit the collector bag (dust bag) E on the sawdust extraction

tube D.

2. Push it rmly onto the sawdust extraction tube D has far

as it will go to avoid the bag E coming off during operation. If

the machine does not extract all the dust, this is probably due

to the quality or moist charac-ter of the material. Blow off the

moist dust particles.

TIP: For best results we recommend emptying the bag E

when approximately half full and shaking it slightly to remove

as much sawdust as possible.

ELECTRONIC SPEED CONTROL

(only mod. FBS100CE)

The electronic speed control I enables the speed of the

sanding belt to be adjusted in different positions num-bered

from 1 al 6. To increase the speed, turn the control I towards

number 6, to decrease the speed, turn towards number 1.

Select the appropriate speed for the nish required and the

part you wish to sand.

Belt sander BSF76/900 BSF100/1200E

Rated power W 900 1200

Sanding belt speed m/min 250 200-400

Sanding belt measurements Mm 76 x 533 100 x 610

Acoustic pressure dB(A) 91,0 96,7

Sound-power level dB(A) 102,0 106,7

Vibration acceleration m/s² 3,7 5,5

Approximate weight (without accessories) according

EPTAProcedure 01/2003

Kg. 3,3 5,3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti BSF100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info