Bedienungsanleitung Felisatti DCF10 (Seite 5 von 32) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

500406

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

See general warranty conditions printed in separate.and drilling ceramics and for starting to drill brick without a

piercer.

• High speed (2) (lever forwards) (DCF10/10.8R) for

drilling brick, for drilling wood and derivatives, plastics and

metals.

The speed can be adjusted while the machine is run-ning.

However, this should not be done at full load. If, when the

machine is stopped, the selector C cannot be set in its nal

position, push the on/off E switch briey.

4. Attachment of bits in the keyless drill chuck

1. Open the drill chuck A and insert the drill bit or screwdriver

bit (in clamp H).

2. To block the bit or screwdriver tip, turn the drill chuck in

a clockwise direction, looking at the ma-chine from the front.

5. Torque adjustment

• For use as a screwdriver, the drill-screwdriver is equipped

with an adjustable clutch, operated by the torque adjustment

control B which has 15 settings. Once it has been correctly

adjusted, the friction clutch is released when the pre-selected

torque setting is reached, to avoid the screw penetrating too

far or damage to the machine. Adjustment depends on the

type and size of the screw used. It is advisable to always

begin in the lowest setting (1) and increase gradually until the

desired result is obtained.

• For use as a drill, set the torque adjustment control B to

the drill setting. The clutch is designed not to work in the drill

mode.

CHARGING THE BATTERY

To remove the battery F from the machine, press both side

buttons, G, situated on the handle, at the same time.

To charge the battery with a quick 45 minute charger, proceed

as follows:

1. Place the battery charger I on a at surface and plug the

charger into the mains.

2. Plug in the charger. the green light on

3. Put the battery in charger. If battery is in good condition,

the red light will be on. If the battery is in poor condition,the

red light will not be on. Please replace the battery.

4. The red light off when the battery is fully charged, ready

for use.

ACCESSORIES

Accessories and their corresponding order number can be

found in our catalogues.

MAINTENANCE AND CARE

Remove the battery before carrying out any opera-tion on

the machine.

- Clean the machine very carefully after each use. The air

vents should always be kept clear.

- Store in a dry place, away from cold .

- Use only Felisatti accessories and spares. These should

be tted in a Felisatti technical service centre (See Warranty/

Technical Service Centre address leaet).

- Brush replacement: The brushes disconnect auto-

matically and should be replaced after 80 - 100 hours use

or when they are less than 3 mm long. Have them replaced

by an Ofcial Service Centre. We re-commend that at every

second change of brushes, you take the machine to one of

our Ofcial Service Centres for general cleaning and oiling.

WARRANTY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti DCF10 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info