Bedienungsanleitung Felisatti DMF23 (Seite 3 von 36) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Finnisch)

502468

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

TECHNICAL DATA

Drill DMF23/1150VSE DMF32/1600VSE

Rated power W 1150 1600

No load speed r.p.m 120-480/255-970 130-280/240-510

Bit adaptation cone Morse 2 3

Maximum capacity in steel mm 23/13 32/16

Maximum capacity in aluminium mm 32/16 50/25

Maximum capacity in wood mm 60/32 80/40

∅ head setting neck

mm 43 63

pprox. weight Kg. 4.4 5.8

The instructions contained in this manual must be strictly

followed, it should be carefully read and kept close at

hand to use when carrying out maintenance on the

indicated parts.

If the machine is used carefully and normal maintenance

is carried out, it will work well for a long time.

The functions and use of the tool you have bought shall

be only those described in this manual. Any other use

of the tool is strictly forbidden.

ILLUSTRATIONS

DESCRIPTION (See figures)

B On-/off switch (Fig.1 and 3)

C Retainer button (Fig.1 and 3)

D Mechanical speed shift lever (Fig.1 and 2)

E Auxiliary grip (Fig.1)

SAFETY INSTRUCTIONS

• See “Safety Instructions” manual, supplied with this

instruction manual.

• Warning! When drilling in amianthus/asbestos

and/or silica stone, the dust produced is extremely

harmful to your health. Wear protection against

inhalation of this dust, in compliance with current

regulations on accident prevention. Follow the in-

surance company’s safety instructions regarding

the responsibility of employees.

• For your personal safety, always connect the machine

to a mains supply protected by a differential and ther-

mal cut-out switch, in accordance with regulations on

low-voltage wiring sitemaps.

• Do not perforate the machine casing, as this would

destroy the protective insulation (use adhesive labels).

• Always unplug the machine before doing any work

on it.

• Warning! Before each use, inspect the plug and lead.

Should they need replacing, have this done by an offi-

cial service centre. Only plug the machine in when it is

switched off.

• Always keep the lead out of the machine’s working

area.

• Only plug the machine in when it is switched off.

• Do not allow the machine to get wet, nor should it be

used in wet environments.

• When using the machine, always wear safety goggles,

gloves and non-slip footwear, and it is advisable to

wear ear protection.

• Do not touch the bit during or immediately after

working, as it becomes very hot and can cause

serious burns.

• Hold the machine firmly by the handle and the auxiliary

handle, otherwise the recoil produced could cause the

machine to work imprecisely or even dangerously.

• Always use the auxiliary handle.

• Never attempt to clean off dust or shavings resulting

from drilling when the machine is operating.

• Do not use diamond core bits.

• When drilling walls, ceilings or floors, take care to

avoid electric wires and gas or water pipes.

BRIEF DESCRIPTION (Mod. DMF32/1600VSE)

The machine is equipped with a safety clutch or mecha-

nism which operates when a bit seizes up, protecting the

user and the machine’s electro-mechanical parts. The

clutch is released automatically.

Warning! This machine must not be used with hole

saws, core bits, etc, as they tend to jam in the hole

easily. This would cause the safety clutch to trip out

too often.

BEFORE USING THIS TOOL

WARNING! Before carrying out any work, check, for

instance, using a metal detector, that there are no elec-

tric wires or gas or water pipes under the surfaces you

wish to work on.

Make sure the mains voltage is correct: it must be

the same as that on the specification label. Ma-

chines with 230V can also be connected to a 220-V

mains supply.

To turn the machine on, press the ON/OFF switch B and

keep it pressed down.

When the ON/OFF switch is released, the machine

stops.

For permanent operation, press the switch and lock it

(Fig.3) by pushing the retainer button C on the actual

trigger. For accurate drilling it is advisable no to lock

the switch.

WARNING! Always disconnect the plug from the socket

before doing any work on the machine.

Mains connection

Warning! Connect only to a single-phase AC current

supply and only to the mains voltage specified on the

rating plate. Connection to sockets without earth protec-

tion is possible as the appliance features protective

class II insulation according to European Standard EN

60745. Radio interference suppression complies with the

European Standard EN 55014.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti DMF23 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info