Bedienungsanleitung Felisatti JSF100-700 (Seite 6 von 40) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

502492

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

The saw blade can be directly inserted into the material (only

for wood work pieces), but this operation should only be

performed by operators with considerable work experience

and with the exclusive use of short blades.

With the machine running, the saw blade should be rested on

theworkpieceatanangleof55°-60°(g.4)inrelationtothe

front edge of the base, it should then be pressed, slowly and

carefully, onto the material.

Therstphaseoftheoperationshouldbeundertakenwith

great care: sudden counter-strokes and overloads during

contact between the blade and work piece, or excessively

rapid penetration of the material, can provoke blade

breakage.

Penetration should only be carried out at maximum speed.

45° ANGLED CUTTING

The straight blade should always be tted for angled or

shapedcuttingoperations(Felisatti000.512.054type).

For circular cuts, use the overturned side cutting regulating

device, with the end bit positioned at the center of the circle

that is to be cut.

For 45° angled cuts to the right or to the left, incline the base

plate.

SIDE GUIDE

If cutting operations need to be carried out at a preset

distancefroma90°rabbet,thespecialsideguideL(Fig.1-2)

(suppliedwiththemachine)canbetted.

The guide should be inserted sideways into the base plate

housing.Inordertoxthedistancefromthedesirededge,

tightentheatheadscrewslocatedonthebase.

ANTI-SHAVINGS PLATE (g.5)

The plate should be inserted into the machine base from

below,asshownintheg.

During cutting operations, the wood bers willbe pressed

against the plate, thus avoiding tears and snags.

The use of the plate is limited to right angle cuts.

SHAVINGS SUCTION UNITS

In order to keep working areas clean and dust free, the

machinehasbeenttedwithasuctionpipeunion.

To carry out this operation, connect a corrugated pipe to this

union.

IMPROPER USE

The functions and use of this tool are those exclusively

indicated in this manual.

Any other use of the tool is explicitly forbidden!

MAINTENANCE

Regular inspection reduces the necessity for maintenance

operations and will keep your tool in good working condition.

The tool bearings and gears are life-long lubricated, however

it is advised to check the condition of the grease in the head

every 100 hours, if necessary replace the grease (use GR-

MU-EP2AGIPgrease,orasimilarproduct).Themotormust

be correctly ventilated during tool operation. For this reason

avoid blocking the air inlets with hands.

The movable needle on the blade support should be

periodically lubricated with a few drops of oil.

After use disconnect the tool from the power supply and

clean carefully.

DISPOSAL

At the end of the machine’s working life, or when it can no

longer be repaired, ensure that it is disposed of according

to the standard regulations of the country in which it is

being used, and that the disposal operation is carried out by

specialized personnel following authorized guidelines.

In all circumstances:

- Do not abandon in the environment;

- Do not dispose of together with solid urban waste

products;

- Contact the special recycling centers.

PARTS REPLACEMENT

Attention! Disconnect the plug from the power supply socket

before replacing any parts.

BRUSHES

The brushes must be replaced after approx. 150-200 working

hours, or if they are less then 5-6 mm in length.

Attention! For correct tool operation always change

the brushes in pairs, not separately. The use of original

Felisatti spare parts is recommended.

Giventhedifcultyofthisoperation,itisadvisedthatitshould

only be performed by an authorized service center.

ATTENTION: After tting new brushes allow the motor to

run idle for 5 minutes.

REPLACING THE POWER SUPPLY CABLE

Check that the power supply cable is in good condition, if not

have it replaced by an authorized service center.

REPLACEMENT OF BLADES (g.6)

For perfect operation and optimal tool performance, only use

originalFelisattiblades.Inordertottheblade,insert the

shank of the saw into the slot located on the lower part of

the gauge block on the saw support shaft, push the blade up

into position, locking in place with the special spanner, the

hexagonal headed screw should be positioned on the side

of the block. The hexagonal key is provided with the machine

andisinsertedinaholeonthesuctionsleeve,ttedonthe

support plate.

WARRANTY

See general warranty conditions printed on the attached

sheet.

NOISE AND VIBRATION

This tool has been designed and made to reduce noise to a

minimum. However, in spite of this, in certain circumstances

the maximum noise level in the place of work could exceed 85

dBA.Inthiscase,theoperatorshouldwearearprotection.

The machine’s noise and vibration levels, measured in

compliance with EN 60745, usually reach:

Acousticpressure=90dB(A)

Sound-powerlevel=101dB(A)

Use ear protection!

Felisatti JSF100-700 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info