Bedienungsanleitung Felisatti JSF100 (Seite 4 von 47) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Finnisch)

502488

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

• A protective face mask must be employed in any

work producing harmful dust. Material containing as-

bestos must not be worked.

• When working with the machine, always wear safety

goggles and ear protection. Other personal protection

equipment such as dust masks, gloves, helmet and

apron should be worn when necessary, along with

non-slip safety footwear. If in doubt, use safety

equipment.

• Never place hands or fingers in front of the saw when

working.

• Make sure the vents are free when working with dust.

If they require cleaning, first unplug the machine, do

not use metal objects and avoid damaging internal

parts.

• When the work is finished, the equipment should

be switched off and the saw blade must be al-

lowed to come to a complete stop before removing

it from the cutting slot and depositing it (danger of

kick-back).

BRIEF DESCRIPTION

This tool has been designed to saw aluminium, metals,

wood, gasified concrete, cardboard-plaster plaques and

similar.

BEFORE USING THIS TOOL

Before using the tool, make sure the mains voltage is

correct: it must be the same as that on the specification

label. Machines with 230V can also be connected to a

220-V mains supply.

Before plugging the tool in, always check that On/Off

switch A is functioning normally and returns to Off

when released.

INSTALLING THE SAW (Fig.2)

WARNING! Always make sure that the tool is switched

off and unplugged before carrying out any work on the

machine.

This jig saw is fitted with a “Quick fix” saw blade retain-

er. Saw blade installation is described below:

- Fully rotate retaining lever F and maintain it in this

position.

- Fully insert the saw blade, with the rear section

supported in wheel guide H.

- Release retaining lever F and press the saw

blade until retaining lever F returns to its original

position. Verify that the saw blade is correctly

fixed in place.

Important: It is essential to respect this instruction.

It is advisable to lubricate periodically the contact area

between the saw blade and support wheel (with a drop

of oil) and the support axle of the wheel itself. Use only

adhesive labels.

Pendulum mechanism adjustment

The pendulum mechanism provides blade swivel

motion with improved cutting and higher work speed

per material.

To adjust with of swivel, use control E (Fig.3). At 0

there is no swivel.

Pendular movement is increased from position 1 to

position 3.

Change of setting can be carried out with the machine

in motion.

Read the optimum operating conditions on machine

label O according to the specific material being worked.

STARTING THE TOOL

WARNING! Plug the machine in with the switch off.

Pressing On/Off switch A will turn the machine on and

releasing it will turn it off again.

For continuous operation, press On/Off switch A and

lock it in the operating position using button retainer B.

If the On/Off switch A is depressed and released once

again, the machine will stop.

Electronic speed regulation

The installed module D permits smooth start-up and

maintains the rated speed practically constant up to the

rated power. Regulator D is located in the upper sec-

tion of the handle (Fig.6).

Adjustment control D is used to set the required speed.

A number 1 corresponds to the minimum speed and

number 6 is the maximum obtainable by means of the

electronic circuit. Once number 6 is exceeded the

circuit switches off and the machine works at the max-

imum speed without regulation.

Electronic regulation can be carried out with the ma-

chine running.

The optimum number of strokes, depends on the

material and particularly on the working conditions

which can be achieved with practice.

If working with a reduced number of strokes for a

prolonged period of time, the machine should be

left at a no-load speed from time to time for a

period of 1 to 3 minutes to allow the motor to cool

down.

TYPES OF CUTS

WARNING! For safety reasons, the machine should

always be unplugged from the mains before changing

the disc or wheel.

Inclined cuts (Fig.5)

To work with inclined cuts, loosen screw I, and incline

the base according to the desired cutting angle, which

is indicated on graduated scale P on the base itself.

Firmly tighten screw I.

The base should be placed as far forward as pos-

sible to allow for unlimited saw blade inclination

(Fig.5 pos. 1).

Vertical cuts

The base is placed as far back as possible so that the

blade is centered at pos. 2 (Fig.5).

To start working on wood on inner cuts the assembly

car be beared through the front portion of the base

plate and slowly press until the saw blade has gone

through the material to be processed.

If there is no training or when working on other

materials it is necessary to make a previous ad-

justment hole.

To carry out this the pendulum mechanism should be at

position 0.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Felisatti JSF100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info