Bedienungsanleitung Felisatti RF67 (Seite 4 von 33) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

502507

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

 The operator should remain alert and keep the milling

head apart from all objects during operation.

 When the milling operation has been completed,

locking lever should be operated so that the machine

returns to its upper starting position.

 The motor must be allowed to come to completely stop

before being put to one side between uses.

 The milling heads should be protected from impacts

and knocks.

 The milling heads should not be touched after use

because they could cause serious burns.

BRIEF DESCRIPTION

This machine is designed for use with rotary milling heads

for milling slots, edges, profiles and rough-edged holes,

from a firm base, in wood, synthetic and light construction

materials, and for milling operation with a copier.

By employing the correct milling heads and using slow

speeds, non-ferrous metals may also be milled.

BEFORE USING THIS TOOL

Make sure the mains voltage is correct: it must be the

same as that on the specification label. Machines with

230-V can also be connected to a 220-V mains supply.

Press the locking button A, and squeeze the trigger in

the on/off switch A1. When the on/off switch is released,

the machine stops.

For safety reasons, it is not possible to lock On/Off

switch A1, instead it has to be pressed while the ma-

chine is being used.

Speed adjustments. Constant electronic performance

The control electronics allow continuous pre-setting of

the revolutions and impact frequency to adapt the ma-

chine to the type of material to be worked on. Adjust-

ment is made using the speed adjustment switch L,

which has 6 positions to regulate the speed.

The higher the number, the greater the speed and

impact energy. The range of settings from “1” (low

power) to “6” (full power) makes the tool very flexible

and adaptable to different applications.

The constant speed control maintains the pre-set num-

ber of revolutions and impact frequency.

Check the speed adjustment label for the desired work-

ing speed.

Revolutions table

Material

 milling

head

Revolution

stages

Hard wood (beech) 4-10 mm

12-20 mm

22-40 mm

5-6

3-4

1-2

Soft wood (pine) 4-10 mm

12-20 mm

22-40 mm

5-6

3-6

1-3

Plywood boards 4-10 mm

12-20 mm

22-40 mm

3-6

2-4

1-3

Synthetic materials 4-15 mm

16-40 mm

2-3

1-2

Aluminum 4-15 mm

16-40 mm

1-2

The values in this table are for guideline purposes only.

The required revolutions will depend on the material and

working conditions. It is recommended that these be

established by carrying out tests with the machine.

MILLING HEAD SELECTION AND INSTALLATION

1.1. Milling head selection

Depending on the materials to be worked, the following

milling head qualities may be selected:

 High-performance, fast-cutting steel milling heads

(HSS): suitable for soft materials, such as soft woods

and plastic.

 Milling heads with hard metal blades (HM): suitable

hard and abrasive materials, such as hard woods and

aluminium.

WARNING! The milling heads that are employed must

be officially approved in accordance with the maximum

revolutions defined for the respective tools. The milling

head shaft diameter should match the inside diameter of

the tool-holder (locking clip).

1.2. Assembly of the milling head option 1 (Fig.8)

WARNING! The mains cable must be removed from the

socket before any adjustments are made to the machine.

It is recommended that protective gloves be worn when

installing or removing milling heads.

1. To assemble the milling head, press the blocking

button of the clip-holder shaft B matching up the

pivot with the axis groove to avoid it from spinning.

2. A 22-mm spanner should be used to loosen clip

fixing nut D in an anticlockwise direction.

3. Insert the milling head so that the shaft enters the

clip by a minimum of 20 mm (shaft length).

4. Tighten the clip fixing nut D with the spanner and

release the clip-carrier shaft support lever B.

PRECAUTION: Do not tighten clip fixing nut D without a

milling head inserted into the clip.

1.3. Assembly of the milling head 2 auto-block

WARNING! The mains cable must be removed from the

socket before any adjustments are made to the machine.

It is recommended that protective gloves be worn when

installing or removing milling heads.

1. To assemble the milling head, move the fixing lever

H, lower the machine to the maximum point and set

the fixing lever H, turn the clip-holder shaft matching

it up the axis groove with the blocking button B.

2. A spanner should be used to loosen clip fixing nut D

in an anticlockwise direction.

3. Insert the milling head so that the shaft enters the

clip by a minimum of 20 mm (shaft length).

4. Tighten the clip fixing nut D with the spanner and

release the clip-carrier shaft support lever B.

PRECAUTION: Do not tighten clip fixing nut D without a

milling head inserted into the clip.

ADJUSTING MILLING OPERATION DEPTH

WARNING! The milling operation depth adjustment

must only be performed with the machine switched off.

The milling operation depth may be adjusted according

to the work to be carried out.

The machine is fitted with a depth stop E, the upper

surface of which is used in conjunction with the gradu-

ated scale Y fine control of the milling operation depth.

For deep cutting operations, it is recommended that

several passes be made, with a reduced chip thickness.

Operate the fixing lever H and slowly push the upper

section of the machine against the depth stop E. Lock

the machine by releasing the fixing lever H.

Felisatti RF67 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info