Bedienungsanleitung Fellowes Quasar E500 (Seite 5 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

502665

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

CORRECTING A BOUND DOCUMENT

REMOVAL OF WASTE CLIPPINGS

WARRANTY

Fellowes warrants all parts of the binder to be free of defects in material and workmanship

for 2 years from the date of purchase by the original consumer. If any part is found to be

defective during warranty period, your sale and exclusive remedy will be repair or replacement,

at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of

abuse, mishandling or unauthorised repair. Any implied warranty, including that of merchant-

ability or ﬁtness for particular purpose, is hereby limited in duration to the appropriate warranty

period set forth above. In no event shall Fellowes be liable for any consequential damages

attributable to this product. This warranty gives you speciﬁc legal rights. You may have other

legal rights that vary from this warranty. The duration, terms and conditions of this warranty are

valid worldwide, except where different limitations, restrictions or conditions may be required by

local law. For more details or to obtain services under this warranty, please contact Fellowes or

your dealer.

TROUBLESHOOTING

Problem

No Green power neon

Red standby neon

Punched holes are not central

Machine will not punch

Punch holes are not parallel to edge.

Partial holes

Damaged hole edges

Waste tray leaks

Cause

Machine is not switched on

Machine is overloaded when punching

Edge guide not set

Blockage

Debris is stuck below dies.

Sheets not correctly aligned to punch pattern.

Possibly overloading the machine

Waste tray is not correctly inserted or ‘burst

feature’ has activated

Solution

Switch on machine at rear next to plug inlet and at the socket.

Press the punch button. The machine will withdraw the punches

and re-set itself. Continue this process until the punch cycle is

complete

Adjust edge guide until hole pattern is correct

Check waste tray is empty. Check for blockage to paper entry.

Take stiff cardboard and slide into the paper entry. Move the

cardboard sideways to release any stray clippings into the

waste tray.

Adjust edge guide and test punch scrap sheets until correct

Punch plastic covers with paper sheets. Reduce number of

sheets being punched.

Check waste tray is empty and ‘burst feature’ is closed.

Additional sheets may be include or removed at any time by opening and then closing the comb as previously described.

The waste tray is located under the machine and is accessed from the right side. For best results empty the tray regularly.

STORAGE

Switch off the machine. Lower the lid. The Quasar-E comb binder is designed to be stored horizontally on the desk.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fellowes Quasar E500 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info