Bedienungsanleitung Fender KXR 200 (Seite 5 von 7) (Englisch)

607105

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

LINE OUTPUT JACKS - Signal from each of the chan-

nels are combined with reverb and effects to form the

input to the power amplifier stage. The Line Outs are

wired from this point. The 1/4 Jack (Item P) and the

XLR jack (Item Q) provide easy connection paths from

the KXR 200 to any external devices, such as a slave

amp or a mixer. It is also useful for recording live per-

formances. Note that inserting a plug into one of the

Line Outs jacks does not interrupt the normal internal

signal flow of the KXR 200.

EFFECTS SEND JACK - This jack is the output of the

effects bus, where all the channels Effects Send are

combined. The signal coming out of this jack could be

used to drive an effects device, a slave amp, or as an

input to a mixer . Note that the signal coming out of

this jack is reverb-free.

EFFECTS RETURN JACK - This jack inputs signal to the

master section of the KXR 200 through the Effects

Return control (Item J). This jack can be used with the

Effects Send Jack (item R) as a patch point for mono

effect devices. This jack can also be used as the input

jack when the KXR 200 is used as a slave amp.

CHANNEL INSERT JACKS - These jacks are wired

post-EQ and post channel volume control. By inserting

an external signal source into one of these jacks,

through a stereo jack wired to the tip and sleeve (with

the ring left floating), the appropriate channel’s EQ

and volume control are bypassed. By shorting the tip

of the inserting jack to its ring, the channel’s signal

and the externally input signal could be mixed togeth-

er. The channel inserts can also serve as effects loop

points by using a stereo jack wired tip=effects send,

and ring=effects return. Note that the layout of the

insert jacks on the back panel is the mirror image of

the channels layout on the front panel.

POWER CORD - This amplifier is equipped with a

grounding type supply cord to reduce the possibility of

shock hazard. Be sure to connect it to a grounded AC

receptacle. The line cord should be connected to a

suitable power source, in accordance with the voltage

and frequency as shown by the power rating on the

rear panel. DO NOT ALTER THE AC (MAINS) PLUG.

NOTE: DO NOT BLOCK THE AIR FLOW TO THE

REAR PANEL; FOR EXAMPLE, BY BACKING THE

AMPLIFIER UP AGAINST A WALL. The rear panel

contains a heatsink that needs air flow to cool off the

amplifier. Blocking the air flow may result in equip-

ment failure due to excessive heat building up inside

the chassis.

WARNING : THIS EQUIPMENT MUST BE EARTH

GROUNDED.

COVERING CARE - UNPLUG THE POWER CORD

BEFORE CLEANING - The exclusive vinyl covering on

your cabinet has been especially designed for years of

lasting beauty. A very light, soapy solution on a

sponge may be used to remove dirt and residue that

may accumulate in the texture. Be careful as not to let

any liquid get inside the chassis or contact the operat-

ing surfaces.

P,Q.

KXR 200 REAR PANEL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fender KXR 200 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info