Bedienungsanleitung Fender Mustang I (Seite 5 von 12) (Englisch)

550707

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

MU STA NG

™

I II/ IV/ V

2. Press the SAVE button. The SAVE and EXIT buttons should

be illuminated. You can press EXIT at this point to cancel

the save process.

3. Turn the DATA WHEEL select a preset destination to

overwrite.

4. Press the DATA WHEEL if you want to edit the name of

your new preset. Use the buttons to perform the functions

listed along the bottom of the screen; turn the DATA

WHEEL to select characters.

5. Press the SAVE button a second time to confirm the save.

♫

Memory Lock must be OFF to save presets (see Utility

Menus, page 6)

Guitar Tuner

Your Mustang™ amplifier has a built-in Tuner mode that turns

the screen into a guitar tuner.

To use the Tuner:

1. Press and hold the TAP button. The TAP and EXIT buttons

will illuminate.

2. Strike any single string on your guitar and watch the

screen. The the note of the string being tuned is displayed

along with a fine tuning needle

3. Turn the tuning peg on your guitar until the fine tuning

needle indicates the string is in tune, as shown above.

4. Standard guitar tuning is as follows:

5. Press EXIT or TAP to exit from the Tuner.

Footswitches

Four-Button Footswitch (0080996000)

Connect a 4-button footswitch to your Mustang amplifier

(included with the Mustang IV & V, optional equipment for

the Mustang III) to enable remote multi-function foot con-

trol. The footswitch display and LEDs show you some of the

same information as the amplifier screen, so you can, for

example, tune your guitar and select presets by watching the

footswitch without ever looking at the screen onboard the

Mustang!

• Select Quick Access presets (QA1/QA2/QA3)

• Select presets (up/down/bank)

• Bypass effects

• Activate the Tuner

The footswitch has three modes that are identified by the

three LEDs labeled MODE 1, MODE 2 and MODE 3. The

footswitch also has a Tuner mode which is indicated when all

of the mode LEDs are off.

To switch between modes, press the MODE button. To acti-

vate Tuner mode, press and hold the MODE button.

Mode 1—In Mode 1 the footswitch is used to select one of

three Quick Access presets, using the buttons labeled: QA1 /

QA2 / QA3 (in line with the MODE 1 LED). When you select a

Quick Access preset, the number of the preset will appear in

the display of the footswitch.

♫

You can any assign any preset to be a Quick Access

preset in the Utility menus. (see Utility Menus, page 6).

Mode 2—In Mode 2 the footswitch is used to select presets

down/up, or in banks of 10, using the buttons labeled: DOWN

/ UP / BANK (in line with the MODE2 LED). When you select a

preset, the number of the preset will appear in the display of

the footswitch.

Mode 3—In Mode 3 the footswitch is used to bypass the

Stompbox, Modulation or Delay effects, using the buttons

labeled: STOMP / MOD / DELAY (in line with the MODE 3

LED). The footswitch button LEDs indicate the effects that are

active, just like the buttons on the amplifier.

Mode indicators

"In tune"

f e n d e r . c o m

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fender Mustang I Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fender Mustang I

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info