Ferm 91
omdrejningshastighed begynder at tage af, skal batteriet oplades. Når du fortsætter med
at bruge boret, og batteriet bliver helt afladet, kan den såkaldte ‘ombyttede poler’-effekt
forekomme. Batteripolernes polaritet bliver byttet om: ‘+’ bliver til ‘-‘ og ‘-‘ bliver til ‘+’. Er
dette først sket, vil polariteten stadig være byttet om under opladningen, og dette vil
skade batteriet uopretteligt.
Hvis akku-boremaskinen ikke skal bruges i en længere periode, skal batteriet lades
helt op forinden. Batteriet skal være opladet under opbevaringen.
Vedligeholdelse
Sørg for, at stikket til maskinen er taget ud af stikkontakten, når der skal udføres
vedligeholdelse på motoren.
Ferm maskiner er blevet konstrueret, så de kan arbejde i længere perioder med et minimum af
vedligeholdelse. Korrekt vedligeholdelse og rengøring af maskinen er en forudsætning for
lang tids tilfredsstillende brug.
Rengøring
Kappen omkring motoren skal rengøres med en blød klud, helst hver gang maskinen har været
brugt. Ventilationsrillerne skal holdes fri for støv og snavs. Hvis snavset ikke vil gå af, bruges en
blød klud vredet op i sæbevand. Der må ikke bruges opløsningsmidler som f.eks. benzin, sprit,
salmiakspiritus o.l. Sådanne opløsningsmidler kan beskadige dele af plastic.
Smøring
Maskinen skal ikke smøres.
FEJL
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på en
genbrugsplads.
Garanti
Garantibetingelser er beskrevet på det separat vedlagte garantibevis.
5. FEJLFINDING
DK
06 Ferm
Thermic protector
Faulty and/or discarded electrical or electronic apparatus have to be collected at the
appropriate recycling locations.
When using power tools, you must observe the follwing basic safety precautions in order to
ensure protection from electric shocks, injury and fire. Read and follow all the instructions
before using this power tool. Look after the notes on safety.
• Remove the battery block. When the power tool is not being used, prior to maintenance
and when changing tools such as the clamping chuck, and drill.
• The tool is suitable for use as a screwdriver and drill. Any other application is specifically
excluded.
Important safety notes on charger and battery block
If you come into contact with acid from the battery block, rinse it off with water immediately. If
acid gets into your eyes, rinse out your eyes at once with water and contact a doctor
immediately!
1. Read and note the operating instructions and safety notes for the charger and battery
block before use!
2. NB! Only use the charger and battery block that were supplied by the manufacturer -
otherwise you will risk an accident.
3. Protect the charger, battery block and power tool from moisture, e.g. rain or snow.
4. Always check that all cables are connected correctly before using the charger.
5. If you discover that a cable is damaged, you should not use the charger again. Have the
damaged cable replaced immediately.
6. When the charger is not in use, the mains plug should be removed from the power socket.
Do not pull out the plug by grasping the cable.
7. If the charger has been dropped or has otherwise been exposed to high mechanical
stresses, you should have it checked for damage by an authorised dealer before using it
again. Damaged parts should be repaired.
8. Exercise caution when handling the battery block and do not drop it or expose it to
impacts.
9. Never attempt to repair the charger or battery block yourself. Repairs must always be
carried out by an authorised dealer - otherwise you risk an accident.
10. Before cleaning or servicing the charger or battery block, always pull the plug from the
charger socket.
11. Never charge the battery block when the ambient temperature is below 10°C or above
40°C.
12. The air vents in the charger must never be blocked.
13. The battery block must not be short-circuited.
A short-circuit will cause a high current to flow. This may result in overheating, the
danger of fire or explosion of the battery block. This may damage the battery block or
the user may risk an accident.
UK
