Bedienungsanleitung Ferm CDM1084 FDSD-1800NK (Seite 7 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

538824

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Ferm

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the

wall outlet.

Remove the battery block when the power tool is

not being used and prior to maintenance.

The tool is suitable for use as a screwdriver and

drill. Any other application is specifically excluded.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Inserting and removing bits

Fig. B

In addition to screwdriver bits with a hexagonal

shaft, this tool can also accommodate drill bits with

a hexagonal shaft.

The bits can easily be placed directly into the bit

holder or on the extension bit holder. The

extension bit holder can be used for screws that

are difficult to reach.

Bit holder selection (9)

Fig. B

With this slider it is possible to push one of the two

bit holders forward while simultaneously retracting

the other. Moving the slider downwards will push

out the lower bit holder. Moving the slider upwards

will push out the upper bit holder. Make sure the

slider is pushed fully to its outer position before

use.

If the bit holder selection knob (9) won’t

move any further, try pressing the on/off

switch (8) shortly while changing

positions.

With this system it will be easy to change quickly

between two different screw bits. Supplied are

short custom made drill bits. These drill bits are

designed especially for pre-drilling. When using

one of these bits together with a screw bit, it is

possible to change quickly from pre-drilling to

screw driving.

The custom made drill bits will have an active

length of 18mm. In forward position optimal length

will be reached.

In retracted position, the drill bit will stick out 5mm.

In some cases this can be problematic. It’s

recommended to remove the drill bit in such a

case.

After drilling holes, the custom made

drill bits can get stuck in the drilled

material. It is recommended to retract

the short drills out of the wood while

keeping On/off switch pressed. When

the drill bits are rotating, chance of the

drill bit getting stuck will be smaller.

When one bit holder is selected, the

other is retracted for 12 mm.

Connecting and removing the battery

Fig. C

Ensure that the exterior of the battery

block or tool is clean and dry before

connecting the charger.

Ensure that the direction reversing switch (5,

•

Fig. A) is in the central position in order to

prevent the appliance from being switched on

unexpectedly.

Insert the battery (7) into the base of the

•

appliance, as shown on the illustration. Push

the battery until it latches in.

Press the locking buttons (6) on both sides

•

before removing the battery, and disengage the

battery from the base of the appliance.

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Hold the appliance firmly and press the drill

steadily onto the workpiece. Do not overload the

appliance. Only use drills with no visible wear.

Worn drills will have a bad effect on the functioning

of the appliance.

Adjusting the speed

Fig. D

The appliance has two drill speeds.

For slow drilling or for driving or removing

•

screws, set the speed selection switch (3) to ‘1’.

CDM1084 # Ma 0807-16.1.indd 7 16-07-2008 11:43:59

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CDM1084 FDSD-1800NK Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info