539082
6
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
EN
6
Ferm
• To remove the bit, slide and hold the locking
sleeve to the rear.
Mode selection lever
Fig.B
• Setthemodeselectionlevertothehammer
position for hammer drilling in concrete and
stone. Do not use this selection for any other
applications.
• Setthemodeselectionlevertothedrilling
without impact position for drilling in wood,
metal, ceramic and plastic. This setting is also
used for screwdriving.
The On/Off switch
Fig. A
• Switch the machine on by pressing the
triggerswitch (2). When you release the
triggerswitch (2) the machine will turn off.
Switching the direction of rotation
• Direction of rotation counter-clockwise: shift
switchto“►”.
• Direction of rotation clockwise: shift switch to
“◄”.
Chuck
A chuck with SDS-10 shaft is shipped with
the product. Please note that the machine is
particularly suited for hammer drilling, the chuck
should only be used for occasional simple drill
work.
• To open the keyless drill chuck, rotate the
chuck body in a clockwise direction until the
jaws open wide enough to accept the bit.
• Insert the bit, over the full length of the jaws,
into the chuck.
• Tighten the chuck jaws onto the bit by turning
the chuck body in a counter clockwise
direction.
The bit must be properly inserted with all
three of the chuck jaws holding the bit
centred in the chuck. Make sure the
chuck jaws grasp the flat sides of a
screwdriver bit. Failure to do so could
cause the bit to be thrown from the
chuck, resulting in possible serious
injury or damage to the chuck
To remove a bit, open the keyless drill chuck by
rotating the chuck body in a clockwise direc tion
until the chuck jaws open and remove the bit.
The adapter can only be used for drilling/
screwdriving without impact. Never use the
adapter with the machine set to Hammer mode.
Hammer drilling in concrete or brick
Caution: Stone drills can get very hot.
It may be necessary to drill with smaller bits and
re-drill to nominal size so that later the plug is
firmly seated.
For large bores, for instance in very hard concrete,
use a smaller bit for pilot drilling and re-drill to
nominal size.
Do not apply a lot of pressure on the machine, let
the machine do the work, guiding the machine with
light pressure is sufficient.
Hold the machine with both hands. The bit can
jam, particularly with deep bores, and the machine
will turn. This can lead to serious injury.
Battery status indicator
The battery status indicator shows the charge
condition of the battery for a few seconds when
the On/Off switch is pressed fully or halfway.
• When 1 LED is lit, the charge is less than 30%
and the battery should be charged.
• When 2 LEDS are lit, the battery is charged
between 30 and 70%.
• When 3 LEDS are lit, the battery is charged
between 70 and 90%.
• When all 4 LEDS are lit, the battery is fully
charged.
Charging the battery
• Plug the adapter directly into the charger
connection (8). Charging will start when the
adapter is plugged into the mains supply.
Temperature overload protection
When using as intended for, the power tool can’t
be subject to overload. When the load is too high
or the battery temperature exceeds 70 ºC, the
electronic control switched off the power tool until
the temperature is within working range again.
The battery status indicator (4) flashes green until
the On/Off switch is released.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ferm CDM1094 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info