Bedienungsanleitung Ferm ETM1003 (Seite 5 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510093

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

To load the tacker

Fig. 3 - 5

Unlocking slide

 Press the slide unlock (2) on both sides to

unlock the slide.

Placing staples

 Remove the slide from the tool.

 Place the staples or nails in the cartridge

Placing nails

 Replace the slide in the tool.

 Lock the slide by sliding the slide forward until

it locks into place.

Using the tacker

 Press the On/Off switch (5) to switch the

machine on

 Press the On/Off switch (5) to switch the

machine off.

Placing the tool

 Place the tool at the spot where the staple or

nail should be located.

 Press the tool down firmly.

Pressing safety catch

 Press the safety catch to the side to unlock

the safety.

Stapling

 Press the switch.

 When the work is completed, slide the safety

catch to the other side to lock the safety back

on.

The tool will cause a re bound because of

the force it operates with. Keep this in

mind.



Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.



Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

 In case a staple or nail is jammed in the tool,

follow the procedure below

• Disconnect the tool.

• Carefully remove the staple or nail from

the tool with a thin object (for example a

knife).

Repairs and servicing should only be

carried out by a qualified technician or

service firm.

Cleaning

Regularly clean the device’s casing with a soft

cloth, preferably after each use. Keep the fan slits

free of dust and dirt. Remove stubborn dirt using

a soft cloth, dampened with soapy water. Do not

use solvents such as benzene, alcohol, ammonia,

etc., which might damage the plastic parts.

Defects

If a defect appears due to a part wearing out,

please contact the service center on the warranty

card. At the end of these instructions there is

an exhaustive overview of the parts that can be

ordered.

Environment

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging.

Damaged and/or disposed of electrical or

electronic devices must be dropped off at

recycling stations intended for that

purpose.



Read the warranty conditions on the separately

supplied warranty card.

Our company policy is aimed at the constant

improvement of our products and we reserve the

right to change the product specification with prior

notification.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm ETM1003 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info