383792
5
Zoom out
Zoom in
Vorherige Seite
1/76
Nächste Seite
GB
5
Ferm
cutinto existing walls or other blind areas.
The protruding blade may cut objects that can
cause kickback.
Safety instructions lower guard
a) Check lower guard for proper closing before
each use. Do not operate the saw if lower
guard does not move freely and close
instantly. Never clamp or tie the lower guard
into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the
lower guard with the retracting handle and
make sure it moves freely and does not touch
the blade or any other part, in all angles and
depths of cut.
b) Check the operation of the lower guard
spring. If the guard and the spring are not
operating properly, they must be serviced
before use. Lower guard may operate
sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
c) Lower guard should be retracted manually
only for special cuts such as “plunge cuts”
and “compound cuts.Raise lower guard
by retracting handle and as soon as blade
enters the material, the lower guard must
be released. For all other sawing, the lower
guard should operate automatically.
d) Always observe that the lower guard is
covering the blade before placing saw down
on bench or floor. An unprotected, coasting
blade will cause the saw to walk backwards,
cutting whatever is in its path. Be aware of the
time it takes for the blade to stop after switch
is released.
Before using the circular saw
Check the following points:
Does the voltage of the motor correspond •
with the mains voltage (appliances for a
mains voltage of 230 V
Are the mains lead and the mains plug in •
a good condition: solid, without any loose
ends or damage;
Is the saw blade missing any teeth or •
showing any cracks, it so must be
replaced immediately.
Make sure the blade is secure.•
Use this circular saw to saw only wood, •
wood-like products.
Do not use circular saw blades wich are •
deformed or damaged.
Do not use HSS blades.•
Only use blades meeting the required •
dimensions, as well as data and descriptions;
Never apply any blades of which the thick-•
ness is greater than that of the riving knife.
Do not stop the blade of a circular saw by •
pressing the blade from the side.
Check that the blade guard can freely move •
and fully closes.
Never lock-up the guard in the open position.•
Never put sideward pressure on the blade. •
This may cause the blade to break.
Be careful when cutting wood with knots, •
nails or cracks in it and/or dirt on it, as these
can cause the blade to get stuck.
Never leave the circular saw unattended.•
Use this circular saw to saw only wood or •
wood-like products.
Using the machine
Use clamps or a vice to hold the work.•
Never remove wood chips and saw dust that •
is close to the saw blade with your hands. If
there are small pieces of wood left between
the fixed and the movable parts, the circular
saw will have to be stopped. The plug needs
to be removed from the socket, before any left
piece can be removed.
Check that the blade is suitable for the spindle •
speed of the circular saw. Do not attempt to
cut before the circular saw has reached full
speed. Make sure the circular saw runs
without load (i.e. is not in contact with the
work) when you switch it on. The circular saw
must have reached its full speed first.
Never cut wood that is thicker than the depth •
of the saw blade.
When cutting in wooden walls or floors, check •
there is no wiring or piping where you intend
to cut.
Switch off the tool and wait until the blade has •
stopped completely before moving the saw
away from the work or putting it down.
Hearing protection should be worn when
using circular saw.
Safety tips for the laser beamer
Never look into the light beam of the laser.•
Never point the light beam of the laser at •
humans or animals.
Do not point the light beam of the laser at •
strongly reflecting material. Hazard from
reflected light.
Only have repairs made to the laser beamer •
by qualified personnel / professional repair
specialists.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ferm fdcs 185 l wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info